IDL Tools T5 (Lynn's $10 Challenge)
-
I went looking for other reviews, and was a little surprised that I could only find mention here and there, never a review. The IDL T10/SeberTool M4 has a lot more out there on it.
I'm happy to give this little tool some attention.
And so, some 'final thoughts'. This is really simple. It's going into my Everyday Carry. I HAD been carrying the IDL T10. Now, it will be the IDL T5. Smaller, lighter, and I was carrying it almost solely for the pliers. But it also has two great essentially full-size drivers. That will free me up to swap out my Super Tinker Swiss Army Knife with other SAKs, to try neat combinations. Although... probably it's gonna be an Explorer, because my eyes are just getting worse every day.

This tool is not going to win the $10 Challenge. I really think it's too limited, but it PAIRS with other tools fantastically. As I pointed out, it works well paired with Swiss Army Knives. I didn't say it above, but this tool weighs almost exactly the same as adding a plier layer to a SAK, and except in some VERY specific cases, I think these pliers are night-and-day better. Certainly up to more difficult (but admittedly less precise) work.
Against the Leatherman Squirt... again, they're 'tougher', but less versatile, particularly for wire cutting.
I generally think of the single most often used function of pliers as granting superhuman grip strength on very small items, and for that, these pliers beat pretty much every other small plier I stacked them against, including the Juice line.
It only has a few functions, but does most of them extremely well, for low weight, and in a small form factor. Complete win as an 'additional' tool.
But I think I can do better for $10.
-
@Lynn LeFey said:
The drivers....
As a Phillips Driver: SOLID Pass.
As a Flathead Driver: SOLID Pass.
As a Pry Tool: Pass for light duty, at very least.Excellent review Lynn - thanks!

-
I have two of these, one is Craftsman branded. They're quite nice.

-
-
as we've been saying for decades now, any "dedicated tool" beats a Multitool on their specific use(s), and this one tiny pliers tool seems like the "dedicated pliers" of the keychain size.

Limited in diversity of functions, but not matched in its design oriented taskI also had trouble bending pretty thin metal wire with small MTs, I bent and misaligned the pivot and head of a Juice with minimal fore and completely trashed a Gerber DIme's jaws twisting thin copper lines

these one are thicker and noticeably tougher,
good review as usual! -
Absolutely, ThePeacent. These things would even bend that heavy 12-gauge copper wire nose-on, and didn't feel like they were straining. They are AMAZINGLY robust. I guess that shot showing the thickness of the various pliers pretty much says it all. In this specific case, there is simply no replacement for more metal.
-
That is what I like about that one. It is inexpensive, but it doesn't feel cheap in any way.
It is good quality, with what I suspect is better quality steel than most, and while it just has a few functions it does them well. That is a lot more useful and reliable than cheap tools that try and fail to do lots of stuff. (Usually discovered when you need them and think you have brought a solution).
Great little SAK companion.

-
Great review, thanks Lynn.

I might just mention the T7 variant of the T5 tool. It is basically the same tool, but adds a small philips and flat driver that fold out from each handle, so you get 4 different screwdriver ends. There are also versions of these tools marketed by SeberTool (the orginal manufacturer), Craftsman and Harley Davidson.
-
@gregozedobe said:
Great review, thanks Lynn.

I might just mention the T7 variant of the T5 tool. It is basically the same tool, but adds a small philips and flat driver that fold out from each handle, so you get 4 different screwdriver ends. There are also versions of these tools marketed by SeberTool (the orginal manufacturer), Craftsman and Harley Davidson.
Right. The SeberTool version of the IDL T7 is known as the M3. I mentioned in the first post about the link to the SeberTech/IDL explanation in the multitooltool wiki. In it, it explains that American made SeberTech was the original manufacturer, and was later bought out, moved to China for manufacturing, and rebranded IDL.
Also, looking for a pic of the tools together, I found Chako's review of the tools. I missed it on a search, because he had 'Serber' instead of 'Seber'. He has a pretty in-depth review of all three models with lots of good side-by-side pics. Here's a link to that thread.
</topic/21516Based on Chako's comparisons, it appears that Seber made the Craftsman and Harley branded versions.
-
Great review
I really like the T5 and to be honest most of my uses of pliers involve small appliance repair for which the T5 works well. Things like removing a few screws, phillips usually, cutting some wires, pulling off a clip. I could probably "survive" just fine with only a Vic Manager and an IDL T5.
Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login