Gerber MP400 refreshed version.
-
Nicely done as always

-
@Sam Lim said:
@Sam Lim said:
A little how-to on installing the clip.
Its a standard Wave/charge clip with a little modification. Somewhere in the middle of the screw post, u will need to cut out a groove for the pocket clip to slide in. See pic and you will get it. A little precision cutting. Go slow. A proper nice cut will minimize any side to side play. On the clip, ground off any excess on the sides and leave some allowance on the bottom 2 "feets". Now side to side is settled if you have done the cut nicely.
Red is the area you need to cut groove. Green is the position of the pocket clip

Next you have prevent it from moving up and down or sliding off. What I did was, I torch the "feets"one by one. When it hot/soft enough, I hammer the buggers to wrap it around the pivot.
See, you are done. Easy as pie.


Nice! Some good thinking there [emoji16]
Sent fra min FRD-L09 via Tapatalk
:)
Just happened that that particular side of the pivot is in a fixed position. That helps alot. And because that clip is already jammed between the frame and post screw, you will be able to still do some adjustment to the tightness of the implements without much affecting the clip.

Great idea!
Sent fra min FRD-L09 via Tapatalk
-
Thanks for the very clear and clever explanation Sam
Great work. -
Are you planning to do anything
else to your MP400 Sam Lim

-
@Sam Lim said:
Thanks for the very clear and clever explanation Sam
Great work.
There's still a little problem though. The gap at the top the clip is a little roomy. It hangs alright but goes not grip tight in the pocket. I snapped one clip before this trying to close the gap.
You can anneal, bend, heat treat the pocket clip pretty easily. I've done a few of them now.
-
@Sam Lim said:
Thanks for the very clear and clever explanation Sam
Great work.
There's still a little problem though. The gap at the top the clip is a little roomy. It hangs alright but goes not grip tight in the pocket. I snapped one clip before this trying to close the gap.
You can anneal, bend, heat treat the pocket clip pretty easily. I've done a few of them now.
Thanks, another quick question, do I really need to heat treat it after annealing? Thought without doing it, it will keep it softer. Lesser chance of breakage? I have almost zero knowledge in these things.
-
Need to find nicer screws at work and tidy up of some corner..



-
That is a nice touch

Can you use it one handed?

-
@Sam Lim said:
That is a nice touch

Can you use it one handed?

Not quite possible.. The back spring on this is rather strong... But then again.... :D
what about a thumb stud
Than you should be able to open one handed
Like in the pic
I.. dun have the capability to drill...
But at the moment I am happy enough.. as long as the blade is outside, I am good. I think. . lets see if I miss OHO.. :)
-
@Sam Lim said:
@Sam Lim said:
That is a nice touch

Can you use it one handed?

Not quite possible.. The back spring on this is rather strong... But then again.... :D
what about a thumb stud
Than you should be able to open one handed
Like in the pic
I.. dun have the capability to drill...
thats a shame Sam
Have you got any engineering shops near you
That you could use
-
Awesome job!

-
:D
Some minor changes to the toolset. Threw the file and can opener back in.

Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login


