Gerber Mr. Pinchy Multi Plier Club
-
It is the plain blade. I don’t see any wear on the ”bump” on the blade, and I don’t see any wear inside the handle where the ”bump” is supposed to touch. The tool had no washers at all between the implements when I got it. But I’m sure this is not the first time someone took it apart

The first picture shows where the edge hits the inside of the handle, and the second picture shows the ”bump” on the plain blade. It looks intact in person


-
I took two pictures of mine to show how far it is supposed to go before touching the handle.
I would bet your multi-plier came from the factory with that issue. The only thing I can think of to fix it would be to reshape the blade to a point the edge is not rubbing on the handle.
Although, based on gow often you'll carry/use, the blade would still be fairly useful without reshaping it.

-
I see
It’s not that big of a deal, I was just curious if all tools had the same issue 
-
I wish every MT was as user serviceable as the Multi-Plier.

-
Oh yeah. Pinchy V.3 was out to play today.


-
@gerleatherberman said:
Oh yeah. Pinchy V.3 was out to play today.
stainless trio!

-
Not quite sure which version I have here. But I just couldnt resist taking things apart.
Initially wanted to remove the super wicked awl for something else but realised its a different size pivot hole.But what I found out contrary to the above posts, the pivot screw at the tools are actually barrel pivots. Not sure if I got the correct term for it. Its one threaded post, with 2 screws on each side. Meaning I have to remove both screws before I can remove any of the implements. Its a bit of a challenge to remove the other end of the screw as theres nothing to hold on to properly.
Being the usual itchy hand here, I added 2 tiny washers to the screw at the sliding part, opening up the splay a little. One side of the lock is disabled. With one side, it locked up still fine. Just for a bit of fun and messing around. Not too keen to get the Coveted Blood Blister Badge...


-
Thanks, ThePeacent!

Sam,
Version 2 right there. Probably my favorite of the pinchy types. Version 3 went to the more common screw through barrel with the captive nut on the other side.
The V1 and V2 had the threaded barrels with a screw on each side.
The awl is also indicative of the V2. The V3 replaced the awl/reamer with a file.
Nice job on opening the splay. Probably the best thing I ever did on my original pinchy. :) -
@Sam Lim said:
Being the usual itchy hand here, I added 2 tiny washers to the screw at the sliding part, opening up the splay a little. One side of the lock is disabled. With one side, it locked up still fine. Just for a bit of fun and messing around. Not too keen to get the Coveted Blood Blister Badge...You chicken ! ....

-
@Sam Lim said:
Being the usual itchy hand here, I added 2 tiny washers to the screw at the sliding part, opening up the splay a little. One side of the lock is disabled. With one side, it locked up still fine. Just for a bit of fun and messing around. Not too keen to get the Coveted Blood Blister Badge...
You chicken ! ....

Yes I am! And I am proud of that!

Hey Greg, have u receive your stuff yet?
-
@Sam Lim said:
Hey Greg, have u receive your stuff yet?
Yes thank you, and very happy with it too

I've sent you two emails so far, have you checked your junk folder ?
Hmm. I cant find those emails. But good to know that it have reach u safe and sound. Thanks again!

-
I'm gonna pinch ya..five times. :ahhh

-
@gerleatherberman said:
I'm gonna pinch ya..five times. :ahhhNice older Gerbers

-
@gerleatherberman said:
I'm gonna pinch ya..five times. :ahhhThe 2nd row, 3rd and 4th doesn't look so pinchy. Did you do something or are they stock? I bet your blood blister badges are piling up..

-
I'm gonna pinch ya..five times. :ahhh
Nice older Gerbers

Thank you, gregozedobe!

@Sam Lim said:
I'm gonna pinch ya..five times. :ahhh
The 2nd row, 3rd and 4th doesn't look so pinchy. Did you do something or are they stock? I bet your blood blister badges are piling up..

Good eye, Sam! The 3rd has little washers I installed between the handles and plier body. 1/16" extra gap, so the bite isn't so bloody. :ahhh
The 4th is a version 4 needle nose with rivets holding in the pliers. I guess by version 4 they designed the plier head to give the handles some splay. Which is nice.
-
I'm gonna pinch ya..five times. :ahhh
Nice older Gerbers

Thank you, gregozedobe!

@Sam Lim said:
I'm gonna pinch ya..five times. :ahhh
The 2nd row, 3rd and 4th doesn't look so pinchy. Did you do something or are they stock? I bet your blood blister badges are piling up..

Good eye, Sam! The 3rd has little washers I installed between the handles and plier body. 1/16" extra gap, so the bite isn't so bloody. :ahhh
The 4th is a version 4 needle nose with rivets holding in the pliers. I guess by version 4 they designed the plier head to give the handles some splay. Which is nice.
I have a version 2 ( I think).. I tried to install a washer inbetween where you mentioned but it's not exactly working. The spring and the buttons are rather short.. Not enough to lock up the pliers when extended.. I ended up only doing on one side only..
-
@Sam Lim said:
I have a version 2 ( I think).. I tried to install a washer inbetween where you mentioned but it's not exactly working. The spring and the buttons are rather short.. Not enough to lock up the pliers when extended.. I ended up only doing on one side only..It takes quite a bit of fiddling to get it perfect. Mine has washers on the "top and bottom" screws on one side and a washer in the "bottom" of the other side.
I carried a v.3 pinchy for over a decade before I got into Multitools as a hobby. At some point, using one everyday, you learn how to use it without getting pinched. Unfortunately I got my badge when I started putting the pinchy back into my edc rotation(and had forgotten the muscle memory to avoid putting my palm close to the handle gap) and got bit.
-
Finally got a good deal on a V.4 BN. The other photos show it with the other Pinchy tools.

Left to right: V.1, V.2, V.3(small plier pivot), V.3(large plier pivot), V.4 BN, and V.4 NN. Please forgive the little piece of tissue in the V.3(small pivot) pliers.





-
Apologies for the bad photos earlier. Hope these are a bit better. :)
Gerber Multi-Plier 1 by None, on Flickr
Gerber Multi-Plier 2 by None, on Flickr
Gerber Multi-Plier 3 by None, on Flickr
Gerber Multi-Plier 4 by None, on Flickr
Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login