Someone gave me a puzzle
-
I have cleaned it up as best as I can:
- Soaked in white vinegar (didn't seem to remove much rust), scrubbed with a toothbrush.
- Sprayed with CRC (similar to WD40), scrubbed with a toothbrush.
- Sanded with 1200 grit sandpaper. The insides of the handles were hard to get at properly.
- Polished with 0000 steel wool.
Here's a dry fit:

I hope I have everything in the right position.
-
This is looking pretty darn good.
As for having trouble getting into the handles to sand, I had best luck with using a small block of wood that was a bit narrower than the inside handle slot, when i did my Micra clean-up. It worked wonderfully. That was with 600 and 2000 automotive wet/dry sandpaper wrapped around the block of wood.
It would still be hard to get into the area around the hinge on the handles, but would save SOME time, I think.
It looks like one of the plier jaws is broken off a bit? You plan to cut the other one down to match?
-
@Lynn LeFey said:
It looks like one of the plier jaws is broken off a bit? You plan to cut the other one down to match?Yes, and I will also see what I can do with the blade.
I thought about using sandpaper around a small block of wood for the inside of the handle but couldn't be bothered! I just used folded sandpaper.
What's the best way to tighten up the pivots (without getting one of Loki's wonderful wrenches)?
-
I should have a PE blade here somewhere and a wrench.
-
@Syncop8r said:
What's the best way to tighten up the pivots (without getting one of Loki's wonderful wrenches)?I just used pliers and vice grips.
As for the blade, I personally recommend if you have a dremel, using a metal cutting wheel to cut down the backside of the blade to the point, like a clip-point or almost wharncliff. I've tried reshaping the tips, and I've tried just cutting the blade down from the back, and cutting it from the back is much faster. Guess it depends on the shape of the tip you want, though. If you DO cut it down with a metal cutting wheel, take care not to overheat the blade to mess up the temper though. I did a little at a time, maybe 2mm, let it cool, then cut more.
Also... nice of you, zoidberg!

-
@Lynn LeFey said:
As for the blade, I personally recommend if you have a dremel, using a metal cutting wheel to cut down the backside of the blade to the point, like a clip-point or almost wharncliff.That was my thinking too. I don't have anything like a dremel so I might try with a half-round file.
-
Some progress.... I started with an angle grinder (slowly with a cut-off disc) and finished with a file.
Not quite the shape I wanted on the pliers but better to quit while I am ahead:

I gave the blade a rough sharpen to get the nicks (nearly) out. Trying to get a concave shape on the back is harder than I imagined:


Perhaps I just go for straight on the back.

-
That's looking pretty good mate.

-
Thanks. I just did a little nibble at a time and it didn't look like heating up.
I happened to have one of these discs on: https://www.georgehenry.co.nz/shop/Abrasives/Cutting+&+Grinding/Norton+115x1x22+Cut-off+disc.html -
Glad to see this little guy brought back to life.

-
Oops.... I meant to post some more "before" pics before the last ones... so here they are:
Pliers:


Blade:


Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login