Lynn's First SAK Mod Build
-
Thanks all.
I THINK the end result is going to be a Master Craftsman.
Not anything terribly exciting from this morning's work. I tore down the two Huntsmans.
The older one...
<a href="https://flic.kr/p/24v9zzm" target="_blank" rel="noopener noreferrer"><img src="https://farm1.staticflickr.com/819/40367615074_27c2a6f4ac_z.jpg" alt="banner" style="max-width: 100%; height: auto;" /></a>The newer one...
<a href="https://flic.kr/p/24v9zuG" target="_blank" rel="noopener noreferrer"><img src="https://farm1.staticflickr.com/818/40367614804_da7f96efbe_z.jpg" alt="banner" style="max-width: 100%; height: auto;" /></a>Four of the 5 liners on the older Huntsman are broken. Not only broken, but extraordinarily brittle. I broke one while taking the tool apart. I don't know what the deal is. However, the stainless steel parts seem mostly in good (not corroded) condition.
The donor Huntsman, the newer one, is in good shape.
I still have to take the Automobile Special apart. I found out this morning that I hadn't drilled out one of the pins sufficiently. It's the small one with no bushings.
I have a set of hardened steel punches I got to do some work on firearms, and those helped immensely. I took the tools out into the garage, and used a center punch to put a starting guide mark on the pins. For the most part, this kept the drill bit in place while i drilled the pins out. When I messed up, either from putting the mark on the pin off center, or the bit wandering, things rapidly got nasty. I'm kind of surprised I didn't screw up worse than I did. Once the pins were drilled out, I used another punch to drive them out, slightly. Enough to be sure they'd move. BUT... I forgot to check one, and have to go back out in the garage, when I get a moment.
After I've gotten these things apart, there is going to be a LOT of part cleaning/polishing to do before assembly, so this isn't getting completed today.
I have an idea for peening, and want to throw it out there to see if it sounds reasonable. What i think I'm going to do on the first peens is the clamp the pin stock between two pieces of wood, then put an old spacer (probably one already broken) on top of the wood, then an old bushing. Then, peen the head into shape, and file flat. The wood 'should' hold the pin from slipping down. The old spacer is just there to support the bushing, and the bushing acts as the form into which the head is peened. If I break the bushing, meh. Get another used one. This should end with a pin head that is peened to the shape of the concave portion of the bushing. If anyone sees anything ludicrously wrong with this, please let me know. I'm really kind of winging it here. The pin in the pic below is not shown actually against the bushing, which is where it would be when shaping. Imagine this is after forming, and the pin has been raised.
<a href="https://flic.kr/p/24vbgzE" target="_blank" rel="noopener noreferrer"><img src="https://farm1.staticflickr.com/798/40367944764_0b0302fae3_z.jpg" alt="banner" style="max-width: 100%; height: auto;" /></a>
-
Interesting idea... go for it and see what happens! :D
The suggested method is to put the SAK together with the unpeened pins, THEN file down to size and peen, so that the head sits nicely in the brushing.
Why not try both ways?
Here’s an informative quote about assembling and peening from tattoosteve:@tattoosteve99 said:
I’ll interject some wisdom. The pins are surely bent. You need some sort of jig for assembly. If you can’t make one use a stack of liners taped together. The pins need to be longer than the finished knife.
The springs are also slightly wider than the tools so they will work.
Here’s my advice.
Hard to explain but I’ll try.
Put pins in jig first.
Outer liner first, then the tool spring, followed by the tools but don’t force them in just yet. Do the non corkscrew or backside philips layer last not this layer. One side of the tools will go in and one side won’t. That’s what you need in order for this to work.
Add a liner and push it down tight as you can. Then use and small pin punch and load the other tool. This will support the pins as you assemble.
After all is together all the tools should still be in the open position. Hold it tight or tape the knife up so it don’t blow apart, not fun if it does.
Then pin the outer pins first, then one with the tools. Don’t hammer them closed just yet, just enough to hold the knife together for now
Next donthe center pivot pin. Then the backside tool pin. This should hold the knife together. Now you can check to see if the tools work correctly and that the pins aren’t bent. Don’t let them snap shut as they can damage the liners
After that’s done and everything looks good. Start pinning it tools side first. They should be very slightly loose. That’s normal. Then do the backside tool pin.
After that the middle pin. This is the tricky one. It’s only purpose is to help support the springs. It should be tight enough to barley spin. Then check snap on each tool separately one at a time. They should all fall correctly in place.
That should correct any issues you have. Hope this all makes sense and is helpful.Sent from my iPhone using Tapatalk
-
What's with the liners on those older SAKs? It seems to be a major issue with SAKs from the '50s and '60s. I had a late 1950s Ranger which all of them were cracked. After about two weeks carry, I noticed a further crack had developed on the back liner closer to the corkscrew pivot.
-
It’s either what happens to the aluminium in old liners when not taken care of, or bad aluminium?

-
I think in the case of mine, it was certainly that the knife had spent some (probably fairly long) amount of time in water.
I think that ate the Aluminum due to Galvanic Corrosion (sometimes called 'electrolysis', incorrectly)
This happens when two different metals touch each other under water that is an electrolyte, like salt water, but will even happen (more slowly) in brackish and fresh water.Here's the kicker. If you want to prevent corrosion on metals around brackish water, Aluminum is your best material to make an Anode out of. The Anode is a piece of sacrificial metal used to take the corrosion, to prevent it on another metal object.
I remember watching a show, maybe an episode of 'Dirty Jobs', where the folks had to crawl down into the steel pylon of a bridge or pier and replace all the zinc anodes. Somewhere in the back of my brain, it got stored that mixing metals in an underwater environment was a 'bad thing', at least for one of those metals. And when pulling the knife apart, I wouldn't have thought about it, except the aluminum was BRITTLE, which I found very very strange.
My six seconds of exhaustive research came up with this...
https://www.westmarine.com/WestAdvisor/Preventing-Galvanic-CorrosionOh... and it wouldn't help to replace the aluminum liners with brass, because then the stainless steel would be less noble than the brass, and the corrosion would most likely affect the stainless steel. So...

Some of this is my speculation as to what happened to my knife, but I think I'm on the right track.
-
Hi Lynn,
I have found it usefull when peening to put little 'shims' between one of the layers
This gives you a little room to play with without over tightening
You can use bits of tin can for shims
But the clever SAK modders on here might have better advice


-
Great read so far
Can't wait to see what you get done next
Good luck and try not to feel overwhelmed as it really isn't that overly complicated of a task
Once you get going it is a lot easier than one would first think 
-
So, a bit more progress...
First, what will probably come as a shock to no one, I ended up cutting myself on the sharp end of a cut pin...
<a href="https://flic.kr/p/FWn4pp" target="_blank" rel="noopener noreferrer"><img src="https://farm1.staticflickr.com/877/26213113537_2677c43e99_z.jpg" alt="banner" style="max-width: 100%; height: auto;" /></a>
While taking the Automobile Special apart. Here it is, though, the last of the three knives to come apart for the build.
<a href="https://flic.kr/p/22QCQ4J" target="_blank" rel="noopener noreferrer"><img src="https://farm1.staticflickr.com/878/39275426840_125a70302d_z.jpg" alt="banner" style="max-width: 100%; height: auto;" /></a>And the new bushings and pins just waiting for me to clean parts up and assemble...
<a href="https://flic.kr/p/FWn4dx" target="_blank" rel="noopener noreferrer"><img src="https://farm1.staticflickr.com/889/26213112907_9280f1e545_z.jpg" alt="banner" style="max-width: 100%; height: auto;" /></a>Thanks again to Syph007 for the bushings, and 50ft-trad for the pin stock.

-
This is interesting to follow.

@Lynn LeFey said:
Oh... and it wouldn't help to replace the aluminum liners with brass, because then the stainless steel would be less noble than the brass, and the corrosion would most likely affect the stainless steel. So...
Brass contains significant amounts of zinc, so chances are that the zinc in the brass would be eaten away first. Hence the general rule to avoid using brass submerged in seawater. (As opposed to some bronzes which are very good for just that).
With galvanic corrosion the relative surface sizes of the metals matter a lot too in practical terms. So you can for instance use stainless steel nuts and bolts to hold together aluminium constructions, but the other way around would be bad.
-
@Sparky415 said:
But the clever SAK modders on here might have better advice
Dunno about clever, but my advice would be to go slowly with a light touch and check often. I've never felt that shims are necessary.
-
@Vidar said:
This is interesting to follow.
@Lynn LeFey said:
Oh... and it wouldn't help to replace the aluminum liners with brass, because then the stainless steel would be less noble than the brass, and the corrosion would most likely affect the stainless steel. So...

Brass contains significant amounts of zinc, so chances are that the zinc in the brass would be eaten away first. Hence the general rule to avoid using brass submerged in seawater. (As opposed to some bronzes which are very good for just that).
With galvanic corrosion the relative surface sizes of the metals matter a lot too in practical terms. So you can for instance use stainless steel nuts and bolts to hold together aluminium constructions, but the other way around would be bad.
According to https://en.wikipedia.org/wiki/Galvanic_corrosion#Galvanic_series, brass has a lower anodic index than aluminium so the aluminium will corrode more/faster. I believe that the liners on older knives were not anodised, which would mean they're more susceptible to corrosion too. There may also be differences in the composition of the alloy.
-
@Lynn LeFey said:
I have an idea for peening, and want to throw it out there to see if it sounds reasonable. What i think I'm going to do on the first peens is the clamp the pin stock between two pieces of wood, then put an old spacer (probably one already broken) on top of the wood, then an old bushing. Then, peen the head into shape, and file flat. The wood 'should' hold the pin from slipping down. The old spacer is just there to support the bushing, and the bushing acts as the form into which the head is peened. If I break the bushing, meh. Get another used one. This should end with a pin head that is peened to the shape of the concave portion of the bushing. If anyone sees anything ludicrously wrong with this, please let me know. I'm really kind of winging it here. The pin in the pic below is not shown actually against the bushing, which is where it would be when shaping. Imagine this is after forming, and the pin has been raised.<a href="https://flic.kr/p/24vbgzE" target="_blank" rel="noopener noreferrer"><img src="https://farm1.staticflickr.com/798/40367944764_0b0302fae3_z.jpg" alt="banner" style="max-width: 100%; height: auto;" /></a>
Just peen the pins into the bushes on the assembled knife. Build the knife onto over-length pins, then when it's fully assembled, position the bushes over the pins. You can use a spare liner to keep the bits in position while you work. Trim the pins with snips/pliers, then file flat leaving yourself 1-1.5mm of exposed pin on each side above the top surface of the bushing. Hammer away from there.
-
@hiraethus said:
According to https://en.wikipedia.org/wiki/Galvanic_corrosion#Galvanic_series, brass has a lower anodic index than aluminium so the aluminium will corrode more/faster. I believe that the liners on older knives were not anodised, which would mean they're more susceptible to corrosion too. There may also be differences in the composition of the alloy.The question then is what brass? There are so many alloys called brass. What they have in common is that they contain copper and zinc. And zinc is the most common material for sacrificial anode use. (Just think of everything that is galvanized).
Brass is suspectible to dezincification where the zinc is selectively eaten away. There are differences between brasses - some additives help reduce the issue, and brasses with little zinc also have less issues. But unless one knows the exact brass alloy used, and the environment it will be used in, it might be safer to just use some better alternative.
Not many will store their SAKs in salt water anyway :)
-
Very interesting reading I might learn
how to do this properly with all these handy tips

-
This is interesting to follow.

@Lynn LeFey said:
Oh... and it wouldn't help to replace the aluminum liners with brass, because then the stainless steel would be less noble than the brass, and the corrosion would most likely affect the stainless steel. So...

Brass contains significant amounts of zinc, so chances are that the zinc in the brass would be eaten away first. Hence the general rule to avoid using brass submerged in seawater. (As opposed to some bronzes which are very good for just that).
With galvanic corrosion the relative surface sizes of the metals matter a lot too in practical terms. So you can for instance use stainless steel nuts and bolts to hold together aluminium constructions, but the other way around would be bad.
According to https://en.wikipedia.org/wiki/Galvanic_corrosion#Galvanic_series, brass has a lower anodic index than aluminium so the aluminium will corrode more/faster. I believe that the liners on older knives were not anodised, which would mean they're more susceptible to corrosion too. There may also be differences in the composition of the alloy.
I thought that the only anodised liner is the one beside the corkscrew/backside philips (but not the one on the scale side).

-
Found info regarding this business of anodizing liners:
@MiniChamp said:
This is my first real post here on the MTO forum. I collect SAKs and I'm very interested in their evolution. I know this place for quite a few years and I learned a lot from reading posts here. Although I usually prefer to just read and learn, this thread touches something that I researched a little bit (by observing the SAKs in my collection), so it seems appropriate to point out what I know.While we are on the subject, I used to think that none of the liners on a standard cellidor were anodized, but the liner adjacent to the blade for sure is clear anodized (you can tell with conductivity test). No other liners are, but why did they do just that one liner and still do it currently? All current cellidor blade liners are indeed alox.
According to my observations, it's indeed true that recent (since some point in the late 1980's) regular-line 91mm Victorinox SAKs have exactly one anodized liner as Syph007 describes. It's the internal liner of the blades layer (namely, the central liner on a Spartan). The full picture, however, is more complex and is part the SAK evolution.
Victorinox used to anodize all aluminum liners of their 91mm and 84mm SAKs since around their official switch to aluminum liners in the very early 1950's (I'm not sure what was before then) to some point in the early 1970's (1973?). Then they completely stopped anodizing the liners of SAKs in the Elinox/Economy/Ecoline line. This change may have coincided (at least roughly) with the other changes that were made to this line around that time (change of tang stamps from big ELINOX over a crossbow to small ELINOX-SWITZERLAND-STAINLESS-ROSTFREI, change of corkscrew to a special economy version, change to polished openers, etc.). It persists to this day, so that except for the use of nylon scales, current ecoline/II versions of 91mm Victorinox SAKs differ from their regular-line versions also by lacking the anodized liner.
Anodizing of all liners persisted for regular-line SAKs until sometime in the late 1980's (1988-89?), at which time Victorinox stopped anodizing all of their liners except for the above mentioned single liner that still gets anodized on regular-line 91mm SAKs.
The next change involved only 84mm knives. They stopped anodizing all liners on all 84mm knives, so that current 84mm SAKs have no anodized liners at all. I don't really know when this happened. Possibly 2005, but for all I know it may have been several years earlier or later (I simply don't have enough 84mm SAKs to determine this at present).
As far as I can tell, Wenger never anodized any liners in their SAKs. This seems to persist for the Victorinox Delemont line.
I have no idea what happens with other sizes (like 111mm) of Victorinox knives that have some aluminum liners.
Finally, while I don't really know why they keep anodizing the particular single liner that they do on 91mm SAKs, my personal theory is that this is due to this liner having an exposed portion (next to the corkscrew/Phillips SD) that is visible and also tends to get easily scratched. Anodizing the corresponding liner usually helps to make this exposed portion look a bit nicer on used SAKs.
-
Thanks Pabs; I stand corrected.

-
No problem.

-
Awesome progress Lynn... can’t wait to see the finished project...
Hope you remembered to take pics of the parts?
Couldn’t find the pics I took for my master craftsman build, but here’s a pic of th parts that went into the Master Ranger build... just ignore the inline phillips layer...

Sent from my iPhone using Tapatalk
Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login

