Lynn's First SAK Mod Build
-
Okay, so... long post coming.
This morning, i started off by lopping off the peening I'd done to the larger pins. Then I tried to assemble the tool, and got it about 95% assembled, was checking the functions and...
Heh... I put the scissors in upside down.

Fine... took it apart and ... couldn't get it back together. I was incapable of getting a tool in to snap the pieces under the spring after another spacer was in, so had been putting the tools in, with spring in place, layer by layer. First, the tools kept popping out from their tensioned position AND the center pin kept just falling out.
I gave up.
For a couple hours.
Then i had the idea of using a piece of wood as a sort of jig to hold the pins. THEN I had the idea of using binder clips to hold the tools together.
And...
<a href="https://flic.kr/p/24WVkA9" target="_blank" rel="noopener noreferrer"><img src="https://farm1.staticflickr.com/818/40659260464_408da3a546_z.jpg" alt="banner" style="max-width: 100%; height: auto;" /></a>
Then the tool started to come together.
Layer by layer... After the opener layer was the scissors...
<a href="https://flic.kr/p/25Y9C4h" target="_blank" rel="noopener noreferrer"><img src="https://farm1.staticflickr.com/816/41329525582_6e3fb6386f_z.jpg" alt="banner" style="max-width: 100%; height: auto;" /></a>
Then the file...
<a href="https://flic.kr/p/HUdvSQ" target="_blank" rel="noopener noreferrer"><img src="https://farm1.staticflickr.com/895/27501527128_7cafe16030_z.jpg" alt="banner" style="max-width: 100%; height: auto;" /></a>
And (not pictured), the blade layer.
From there, I had a firm hold on all the tool layers, and wrapped it in electrical tape to hold everything together.
<a href="https://flic.kr/p/25Y9BXf" target="_blank" rel="noopener noreferrer"><img src="https://farm1.staticflickr.com/799/41329525232_45dc0336be_z.jpg" alt="banner" style="max-width: 100%; height: auto;" /></a>
I cut off the pins with the wire cutters of a Gerber MP600. Once out in the garage, I placed the bushings on the first pin and started peening.
<a href="https://flic.kr/p/HUdvLY" target="_blank" rel="noopener noreferrer"><img src="https://farm1.staticflickr.com/889/27501526788_fe63201822_z.jpg" alt="banner" style="max-width: 100%; height: auto;" /></a>
I peened all the pins just to the point where it was holding the tool together, and then started checking side to side play in the tools as I went.
<a href="https://flic.kr/p/25Y9BSA" target="_blank" rel="noopener noreferrer"><img src="https://farm1.staticflickr.com/819/41329524962_09a04ae4b5_z.jpg" alt="banner" style="max-width: 100%; height: auto;" /></a>
There were several instances where I didn't cut the pins short enough (I guess better that than too short, huh?) and had to go back with the cutting wheel of my dremel to adjust and repeen.
I filed down the rough remains. I also tried using a hardened punch to dimple the ends of the pins, hoping to seat them better, but if this actually accomplished anything, I couldn't tell.
Finally, back in the house, and pressed the scales back on. When i removed them from the original knife, I bathed the knife in as hot of water as I could stand, hoping to soften the plastic of the scales to do minimal damage and allow them to just be press fit back on, and I don't know if it was that or just luck, but it worked. They are on solid with no wobble just from a press fit.
And here is it... A one-of-a-kind 'Grand Prix'.
<a href="https://flic.kr/p/HUdvHb" target="_blank" rel="noopener noreferrer"><img src="https://farm1.staticflickr.com/787/27501526568_7cb038cc44_z.jpg" alt="banner" style="max-width: 100%; height: auto;" /></a>
It has the opener layer of an early 70s Huntsman, including '+ PAT' on the can opener, awl with no sewing eye, and inside sharpened edge on the cap lifter. It has the newish scissor layer, still has a screw at the pivot, but has backside parcel hook. I decided to use the newer scissors because they were the best available, and replacement springs are easier to find (and replace). It has the file layer from the Automobile Special, which also donated its scales. And it has the newer blade layer of the same Huntsman that donated its scissors, except I swapped the Corkscrew for the square shanked phillips with tin key of the Automobile Special.
I would have loved to keep the small clip-point blade of the older Huntsman, but I didn't want to go messing with mixing parts from different blade layers. I seem to recall Gareth mentioning that it's a BAD IDEA (tm).
So...
SMURF YEAH! I DID IT! :ahhh

-
Looking good! And that awl that work paid of [emoji854] nice work
[It's not failure if you learn something from it]
-
Great WIP pictures Lynn

Nice job

-
Nicely done Lynn !

-
Thanks all.
I think I managed to find every conceivable way to screw up at every single step, ruining a few liners during disassembly, failing on the initial peening, so wasting precious pin stock, assembling wrong.

It was absolutely a learning experience.

-
great mod Lynn
I like your jig. -
Nicely done Lynn

And some excellent jig work

-
Looking good :) I'm getting all inspired here :)
After witnessing all your peenful experiences I thought I'd finally get around to try some threading instead. I expect that will cause issues with the handles of course, but that is another bridge to kick down the road. Or something.
Anyway, the nearest thing to a standard nut size for a 2.25mm rod would be M2.2. That is kind of rare though, so I have no such nuts around here. So instead I figure going up to M2.5 make more sense. That is a common size for both rods and nuts. The rod I found is copper, but that will do just for testing I figure.
This was more nimble work than I thought. After filing the rod end slightly pointy to get an easy and straight start it worked out fine. So under are pictures of the threaded rod and nut, nut on rod, and finally a tube with internal ø2.5mm diameter sliding freely on just to check for straightness. A 91mm SAK tweezer added for scale along with a MultiTool.org sticker as background. (And note to self; clean off threads before taking pictures
)Not really easier than peening, but maybe more adjustable and flexible for later changes. Maybe better for Wengers - I think I remember the handle being fastened differently than for Victorinox, so nuts might not be an issue for Wenger?



-
Great work on your first mod [emoji106] Congrats!
Sent fra min FRD-L09 via Tapatalk
-
Nice work Lynn !
I followed this thread with interest.
Just enough drama and suspense to think " is she gonna stick with it, or abort the mission " ?
Happy to see you stuck with it and succeeded !
No quit in this Lady!
-
@Vidar said:
This is interesting to follow.
@Lynn LeFey said:
Oh... and it wouldn't help to replace the aluminum liners with brass, because then the stainless steel would be less noble than the brass, and the corrosion would most likely affect the stainless steel. So...

Brass contains significant amounts of zinc, so chances are that the zinc in the brass would be eaten away first. Hence the general rule to avoid using brass submerged in seawater. (As opposed to some bronzes which are very good for just that).
With galvanic corrosion the relative surface sizes of the metals matter a lot too in practical terms. So you can for instance use stainless steel nuts and bolts to hold together aluminium constructions, but the other way around would be bad.
I wanted to come back to this point.
Right. For some reason, even KNOWING they were brass, my brain was saying 'bronze'. They're not bronze. So... What Vidar said.

-
@Marcellus said:
No quit in this Lady!Actually, I have a whole pile of 'never finished' projects. But THIS one was done to completion. Thanks for the kind words, though.

-
Very nice work, Lynn!

I have yet to get into SAK modding, but this thread has a lot of tips and tricks that inspires confidence with SAK modding!
Vidar,
Please keep us up-to-date on your threaded rod progress!
-
@gerleatherberman said:
Very nice work, Lynn!
I have yet to get into SAK modding, but this thread has a lot of tips and tricks that inspires confidence with SAK modding!

Honestly, a big thing that pressed me toward doing this was to encourage others to give it a try. I am BY FAR not the most skilled person at this kind of crafting. And I think if I can do it, most anyone with some effort and patience can.
And a dremel... and a hand drill, and files. Oh, and hardened metal punches.
Jeez... come to think of it, it's not just my collection of multitools that has grown since joining this forum. I have a pretty big collection of hand and power tools for working on MTs now.
What I'd recommend is go on ebay, and look for those SAKs that beg to be saved/rehabbed. Get a couple for cheap(ish), and go for it. Absolute WORST case is you mess up already-messed-up tools. That was my plan, and it seemed to work out. I'd have to check but I think the three donor tools and additional parts cost me maybe $40 total.
You can do it! It's like lego for MT addicts. :D
-
@Lynn LeFey said:
Very nice work, Lynn!

I have yet to get into SAK modding, but this thread has a lot of tips and tricks that inspires confidence with SAK modding!

Honestly, a big thing that pressed me toward doing this was to encourage others to give it a try. I am BY FAR not the most skilled person at this kind of crafting. And I think if I can do it, most anyone with some effort and patience can.
And a dremel... and a hand drill, and files. Oh, and hardened metal punches.
Jeez... come to think of it, it's not just my collection of multitools that has grown since joining this forum. I have a pretty big collection of hand and power tools for working on MTs now.
What I'd recommend is go on ebay, and look for those SAKs that beg to be saved/rehabbed. Get a couple for cheap(ish), and go for it. Absolute WORST case is you mess up already-messed-up tools. That was my plan, and it seemed to work out. I'd have to check but I think the three donor tools and additional parts cost me maybe $40 total.
You can do it! It's like lego for MT addicts. :D
Thank you for that! This has me on the prowl for donor SAKs!
I know exactly what you mean about the tools. I never had much experiece with metal working, but MT repairs and light modding have introduced several tools needed. I only have a $50 drill press from Harbor Freight, but it is leaps and bounds better than using a hand drill. I have a "1 small belt sander for knife work from there as well ($60 I think). I got a small 6 & 1/2" metal cut off saw as well at a yard sale.
Now I need to find out where I can buy a cure for my laziness.
-
Awesome work there Lynn... I knew you could do it... The first one is always the hardest... the next ones will be easier...

-
I had both fun and learning interest in this thread. :D
Good for you Lynn, and thanks for sharing this little modding adventure!!

-
Really good job! Informative and motivational for all us "wanna-be-modders-who-have-lots-of-ideas-but-never-gets-around-to-realize-them" (or is that just me?)

Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login

