Side-by-Side Comparison Photo Request Thread - Ask for them here
-
-
@hiraethus said:
My Cybertool collection:I need a 41.
Nice collection hiraethus!

-
Victorinox 74mm comparison:
* Prince with Stainless Scales * Prince with Cellidor Scales * Ambassador * ExecutiveThe Prince and Ambassador are single layer. The Executive is two layer.
The Prince is an Escort with several tools added:
* Small blade opposite the large one * Key ring * Toothpick and tweezersAn Ambassador is a Prince with swapped out tools:
* Small blade replaced with short non-SD nail file used on 58mm Classic * Long nail file on back replaced with scissorsA look at the four from their sides . . .

A look at the four from their edges . . .

The main blade tang width on all is 2.2mm. The width of both the long nail file and the scissors at the pivot are also 2.2mm.Added arrows to show how Victorinox made room for the second blade on the Prince and short nail file on the Ambassador opposite the large blade, without increasing width between the liners. That means all the Cellidor single layer should be the same overall width, including the Escort which isn't shown. Likewise, the Windsor which is an Ambassador with stainless scales, also not shown, should be the same width as a Prince with stainless scales. The difference between the measured width of the Cellidor Prince and Ambassador had me puzzled for a while until I measured their widths at three points: key ring end above the pivots (concealed by the scales), middle, and T&T end above the pivots. Some bulge in the middle of the scales is normal and to be expected.
* Cellidor Prince: 8.3mm - 8.4mm - 8.2mm * Ambassador: 8.5mm - 8.7mm - 8.3mmThen looked at the two using 10x magnifier glasses. That is when I noted the larger liner bulge in the middle of the Ambassador. The only rivets are the pair of pivots at each end, similar to the 58mm. It's the same design concept. There are no riveted pivots or pins in the middle of the 74mm SAKs. The photo shows some of it. Conclusion regarding single layer 74mm SAKs: the width between the liners at the pivot points is the same on all of them, 2.2mm. The different single layer with stainless scales are essentially the same overall width and the different single layer with Cellidor scales are essentially the same overall width. Differences between specific examples are attributable to scales thickness variation and variation in how much the liners bulge in the middle of the SAK.
John
-
Does anyone have a Kershaw Skyline? If so, would you be willing to post a picture of that next to a 91mm SAK. The picture I am looking for is each with the main blade extended and looking from the back of the blade. I am trying to get a good feel for how much thicker the Skyline blade is to the SAK's main one. Thanks!
-
@evh said:
Does anyone have a Kershaw Skyline? If so, would you be willing to post a picture of that next to a 91mm SAK. The picture I am looking for is each with the main blade extended and looking from the back of the blade. I am trying to get a good feel for how much thicker the Skyline blade is to the SAK's main one. Thanks!I did find this article showing a Kershaw blade next to a SAK blade, but not the spine.
I wish I could help, but I don't currently have any Kershaw, I have Chris Reeve, Emerson, if that is of any help.
The link:
http://www.swissarmyknights.com/articles/2010/may-2010/241-kershaw-sak -
A side-by-side of 93mm, 84mm and a 75mm Alox showing their scales thicknesses. The difference between the 93mm and 84mm is quite dramatic. Nevertheless, the 84mm remain quite rigid.

From left to right:
93mm:* Pioneer X * Pioneer (for this purpose it's same as the 1961 Soldier and Wenger Standard Issue) * Pioneer Solo84mm:
* Cadet * Bantam * Excelsior * Sentry75mm:
* BeginnerJohn
-
1974 Wenger Soldier vs 2006 Victorinox Soldier








-
Wenger with reshaped awl




-
New layer index format
Very nice new pic at the bottom - Thanks Jalind :salute: :D
-
WorkChamp next to WorkChamp XL

-
The XL's and their counterparts:

Top:
SwissChamp XL and SwissChampBottom:
MiniChamp XL and MiniChampRight:
WorkChamp XL and WorkChamp -
@FolderBeholder said:
WorkChamp next to WorkChamp XLNice comparison pic FB!

-
@FolderBeholder said:
The XL's and their counterparts:Great XL comparisons FB!

-
That WorkChamp XL looks huge next to the WorkChamp!

-
@FolderBeholder said:
The XL's and their counterparts:Really great pic FB - Yep the Workchamp is big but the XL is a monster
So you have the slide-lock versions - Better get the liner-lock versions now!!
:D -
Great thread with pics of blade, saw and scisssor comparisons for pretty much all SAK model sizes from Echotech
/post/2197772
-
Some really nice comparison shots from Pietervn of the Victorinox 111mm Master RT vs the Vic Soldier in this thread:
/post/2356449
-
Nice comparison shot of Wenger vs Delemont scales
@Bunk Tuppins said:
I got a Wenger S101 today. I had the Delemont version of this in red and was looking for one with Evogrip scales and came across this Wenger version on ebay new for quite a reasonable price and picked it up, In the comparison, the Wenger is on the right and Delemont on left. Note how the Wenger scales cover the aluminum liners.
Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login

