And so it begins.... (My adventures into Alox!)
-
I really love that SAK with the Maple Leaf...now you are pulling my heart strings... :)
-
Me too ....
Must have some Canadian in me somewhere
??? :D -
Super busy Sir?
I am going to need a drawer mod knife.
Please take my monies.
-
Would be cool to buy spring plus scissors for 84 mm that you planned on tuning from 91 mm. That and two liners (I'm thinking of getting a cadet 2017 LE and add the scissors and upgrade the liners). That anything you'd be willing to do.
Just thought of the holes. You be willing too sell pivots and screws too? I realise this pretty much ends up with a lot of work but if you're willing then I'm interested!
- stoneshank
-
@HarleyXJGuy said:
Super busy Sir?I am going to need a drawer mod knife.
Please take my monies.
I'm building a dozen pioneer x with drawer this week if you want one of those?
-
So. First off I'm a fan of your mods. Both the 93mm and the 91. All very nice and excellent craftsmanship.
I decided after reading most of this section of the forum to try to make an alox exlporer. After finally getting all the parts and tools I got some time in the shop last night. I present my version of an alox explorer (based off lots of input gleaned from this site. It's not perfect, but I'm happy.
2 alox pioneers
1 celidor explorer.I used the scissor rest from the 91mm explorer and a blade spring to make the scissor layer. I also used one of the 91mm liners with a new hole drilled. The pivots are the 1/8in.
I'm pleased with the result. But there is an issue. The snap on the spring is weak, and the opener layer sits a bit low. I've been playing with this for most of the morning and i think with a little more tension in the spring it would all work.....any suggestions how to accomplish this?


-
Super busy Sir?
I am going to need a drawer mod knife.
Please take my monies.
I'm building a dozen pioneer x with drawer this week if you want one of those?
Silver?
Bah who am I kidding.
Yes I would love one of them.
-
Ok. Quick update.
Problems solved. The scissor rest on the spring was a little loose. I adjjsted the backspring by about 2 degrees. All fit tight. Snap is perfect.Thanks for the inspirarion.
Cheers,
-
@armi101 said:
So. First off I'm a fan of your mods. Both the 93mm and the 91. All very nice and excellent craftsmanship.I decided after reading most of this section of the forum to try to make an alox exlporer. After finally getting all the parts and tools I got some time in the shop last night. I present my version of an alox explorer (based off lots of input gleaned from this site. It's not perfect, but I'm happy.
2 alox pioneers
1 celidor explorer.I used the scissor rest from the 91mm explorer and a blade spring to make the scissor layer. I also used one of the 91mm liners with a new hole drilled. The pivots are the 1/8in.
I'm pleased with the result. But there is an issue. The snap on the spring is weak, and the opener layer sits a bit low. I've been playing with this for most of the morning and i think with a little more tension in the spring it would all work.....any suggestions how to accomplish this?
Nice job. Its such a pain to fit tools on that frame that dont belong. I dont do that kind of work at all anymore. As soon as someone wants Mag/phillips or pliers its 91mm for sure.
Super busy Sir?
I am going to need a drawer mod knife.
Please take my monies.
I'm building a dozen pioneer x with drawer this week if you want one of those?
Silver?
Bah who am I kidding.
Yes I would love one of them.
I'll pm you.
-
What tools would you need to cut out and finish some brass liners by hand, besides patience and practice?
Was thinking of trying my hand at it... have some Al liners to use as a template. -
Fret saw and a plentiful supply of very fine pitch blade (I used 59 TPI :o), files and sandpaper. If you can stack the liners and rivet them together while you work it's easier to cut they'll all be the same size.
-
@hiraethus said:
Fret saw and a plentiful supply of very fine pitch blade (I used 59 TPI :o), files and sandpaper. If you can stack the liners and rivet them together while you work it's easier to cut they'll all be the same size.Yup exactly. Make a liner sandwich with the stock liners on the outside. Then you can just file and sand away. When I used to hand form scales, I'd put them in there too so everything was guaranteed to all match.
-
@stoneshank said:
Would be cool to buy spring plus scissors for 84 mm that you planned on tuning from 91 mm. That and two liners (I'm thinking of getting a cadet 2017 LE and add the scissors and upgrade the liners). That anything you'd be willing to do.Just thought of the holes. You be willing too sell pivots and screws too? I realise this pretty much ends up with a lot of work but if you're willing then I'm interested!
- stoneshank
So far I have 5 cadets I am converting to Ti frame with scissors added. The cost to make these is going to be more than a standard 91mm. So its kind of a test to see if all the people asking for one of these really wants them or not. Just making the scissors layer mods alone would be close to 100 in labor.
Nothing Im making or working with will work on alox scales.
-
@hiraethus said:
Fret saw and a plentiful supply of very fine pitch blade (I used 59 TPI :o), files and sandpaper. If you can stack the liners and rivet them together while you work it's easier to cut they'll all be the same size.Fret saw and a plentiful supply of very fine pitch blade (I used 59 TPI :o), files and sandpaper. If you can stack the liners and rivet them together while you work it's easier to cut they'll all be the same size.
Yup exactly. Make a liner sandwich with the stock liners on the outside. Then you can just file and sand away. When I used to hand form scales, I'd put them in there too so everything was guaranteed to all match.
Ok, thanks. :)
I think I have a source of some K&S engineering .032x2”x12” brass strip, three should cost about €10.
This is what K&S engineering says about the brass specs: Alloy 260 1/2 hard ASTM B36.
No idea what that means.
Is it an appropriate alloy?Fret saw, files and sandpaper should be easy to get... will look in boot sales. And if I have to buy new a saw, plenty of <€15 budget choices to choose from, 5” depth should be more than enough.
That leaves those ultra fine blades to figure out.

-
The thicker the material (or the more liners you cut at once), the lower the TPI count you need. You won't be able to cut very thin material with a coarse blade, as the teeth just catch. Ideally, you need a few teeth in contact with the material at any one time. I think my liners were either 0.7 or 0.8 mm brass.
260 half-hard brass will be just fine, and 0.032" is 0.81 mm, so the thickness is about right too.
You'll find the blades at any fine woodwork or marquetry supplier. I think mine were Pegas brand.
-
Would be cool to buy spring plus scissors for 84 mm that you planned on tuning from 91 mm. That and two liners (I'm thinking of getting a cadet 2017 LE and add the scissors and upgrade the liners). That anything you'd be willing to do.
Just thought of the holes. You be willing too sell pivots and screws too? I realise this pretty much ends up with a lot of work but if you're willing then I'm interested!
- stoneshank
So far I have 5 cadets I am converting to Ti frame with scissors added. The cost to make these is going to be more than a standard 91mm. So its kind of a test to see if all the people asking for one of these really wants them or not. Just making the scissors layer mods alone would be close to 100 in labor.
Nothing Im making or working with will work on alox scales.
Ok, thanks! [emoji9]
- stoneshank
-
Hoping someone might be able to help me out with this. The can opener sits just a hair too low. I can just barely get the nail nick if my nail is long enough, and it hasn't been a problem. But if it was a little higher it would work much better. ...any thoughts on how to raise it?

-
@armi101 said:
Hoping someone might be able to help me out with this. The can opener sits just a hair too low. I can just barely get the nail nick if my nail is long enough, and it hasn't been a problem. But if it was a little higher it would work much better. ...any thoughts on how to raise it?Weird. Did you accidentally out the backspring in backwards? The smaller pivot end goes to the bottle opener. That the only thing I can think of as to why it would sit weird.
Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login
