Access to Power -SOG 30-day Challenge! Starting June 1st! Access & Access Deluxe
-
@Dutch_Tooler said:
I am almost dreading my nail cutting test now... :oThen don't do it. :D It is not on the challenge sheet. Nor is cutting hardened steel nails listed as a function of the PAD.
-
@Dutch_Tooler said:
On that last pic GLBM, how solid was the sensation you got from the PAD when tightening the bolt? Haven't tried that yet...The only thing I wasn't too thrilled about is the slight looseness of the tool inside the socket. But, that is not a problem with the tool, it is just an issue with having 1/2 of a 1/4" driver to do it. :)
-
@gerleatherberman said:
don’t know how Powernoodle got away with cutting that nail he did
Skill. Talent. Good looks. Its all part of the same continuum.
In Nutnfancy's Youtube review of the Swisstool several years ago, he cut a nail in half too with no damage.
PN shouldn't have done it either. Makes little to no sense.

Now, you know that MTO is not about making sense. A bunch of semi-grown men posting pictures of MTs on the internet makes no sense.

For one, I did not care if I destroyed the PAD because I just didn't like it, and because I own more MTs than I can ever use. That is to say, I was prepared to totally destroy the hard wire cutter. And, its fun to cut a framing nail. We do this stuff for fun. Further, it like what "Tim" does on the Military Arms Channel on Youtube. He dunks a gun in water, dirt, sand and mud, and then sees if it still goes bang. That's not the intended usage of a firearm, and not really "fair" to the maker, but that's how you see where its failure point is. You do what's not fair.
Fair or not, its just a data point. You might remember that I've buried more than one MT in the ground for a year to see if it will rust.
/topic/61008 Again, that's outside the MTs design parameters, just like cutting a 10-penny nail may be, but this is not about being fair to SOG. Its about having fun, and maybe learning what your MT can do and what it cannot. My PAD would cut a big, fat nail in half, but that is something I would never do for real. -
powernoodle,
I cannot disagree with your excellently written reply. However, with that said, I should restate my assertion to make more sense.
I should have been clear with my original comment. In essence, regarding the current thread, this particular challenge is about seeing if the PAD can handle routine multitool tasks. Cutting big-smurfin' nails IS fun to try an MT on, but isn't something a majority of us will EVER need to do.
-
**Day 11 continued **
Here are some close ups of the damage
I don’t know how Powernoodle
got away with cutting that nail he did
I gotta call ya out on the nail thing, W.
PN shouldn't have done it either. Makes little to no sense.
That is not a fair test to be honest. SOG doesn't advertise the cutters as "hard nail cutters".
That will not likely be covered under warranty. It is basically abuse.
Edit: For the record, and I emphasize this, I am not cutting hardened nails with my PAD. I don't do it with any other MT, so why ruin my PAD warranty? I urge anyone to NOT void their warranty by cutting hardened nails.
I was in no way trying to test the cutters to their limits
I just wanted to test the cutters with the nail
As Powernoodle cut that large nail
After his test I thought it would
be no problem to cut a 2.5 mm nail
I also tested this with my LM Supertool
And no problems or damageI will say that it’s only a small bit of damage
As I made close up pics to show the damage
I tested the cutters again with the bit of damage
And they still cut everything I used for the test
Just didn’t try a nail again as I now know it’s limitI am not saying that the cutters are no good
As they work and cut everything I tried and still work
I am more a bit surprised after
Powernoodle cutting that large nail
That my cutters got that bit of damageBut I totally agree don’t try and cut nails with the hard wire cutters

-
On that last pic GLBM, how solid was the sensation you got from the PAD when tightening the bolt? Haven't tried that yet...
The only thing I wasn't too thrilled about is the slight looseness of the tool inside the socket. But, that is not a problem with the tool, it is just an issue with having 1/2 of a 1/4" driver to do it. :)

-
@Wspeed said:
I don’t know how Powernoodlegot away with cutting that nail he did

I honestly did, though. I would lie to you about most things
, but not that. I could not take a pic of the actual cutting because it took two hands to bear down on the PAD.I believe that you cut that nail
I was more surprised that a
2.5mm nail would of been a problem
I didn’t even use a lot of force to cut the nail
This is why I said I don’t know
how you got away with no damage
-
@Wspeed said:
I was in no way trying to test the cutters to their limits
I just wanted to test the cutters with the nail
As Powernoodle cut that large nail
After his test I thought it would
be no problem to cut a 2.5 mm nail
I also tested this with my LM Supertool
And no problems or damageI will say that it’s only a small bit of damage
As I made close up pics to show the damage
I tested the cutters again with the bit of damage
And they still cut everything I used for the test
Just didn’t try a nail again as I now know it’s limitI am not saying that the cutters are no good
As they work and cut everything I tried and still work
I am more a bit surprised after
Powernoodle cutting that large nail
That my cutters got that bit of damageBut I totally agree don’t try and cut nails with the hard wire cutters

Fair enough. I had misread your point earlier. Apologies for that. Now I understand you were curious as to why someone else did the cut w/o issue and you had slight damage cutting a nail.

I don't know how it will affect the cutters, but if it does affect the performance, there is a solution. A flattened diamond coated needle file works well at fixing the deformation in the cutters. It may at least prevent any "catching" when the jaws close. That is, of course, if an issue with the cutters were to arise. :)
-
I was in no way trying to test the cutters to their limits
I just wanted to test the cutters with the nail
As Powernoodle cut that large nail
After his test I thought it would
be no problem to cut a 2.5 mm nail
I also tested this with my LM Supertool
And no problems or damageI will say that it’s only a small bit of damage
As I made close up pics to show the damage
I tested the cutters again with the bit of damage
And they still cut everything I used for the test
Just didn’t try a nail again as I now know it’s limitI am not saying that the cutters are no good
As they work and cut everything I tried and still work
I am more a bit surprised after
Powernoodle cutting that large nail
That my cutters got that bit of damageBut I totally agree don’t try and cut nails with the hard wire cutters

Fair enough. I had misread your point earlier. Apologies for that. Now I understand you were curious as to why someone else did the cut w/o issue and you had slight damage cutting a nail.

I don't know how it will affect the cutters, but if it does affect the performance, there is a solution. A flattened diamond coated needle file works well at fixing the deformation in the cutters. It may at least prevent any "catching" when the jaws close. That is, of course, if an issue with the cutters were to arise. :)
Thanks GLBM

The cutters still work perfectly
I haven’t had any problems with cutting
-
Glad the damage didn't have any negative effects, W!
So how are you all doing with your checklists? :)
I have the can opener, cap lifter, plain blade carve/food/rope/eyc, ruler, and final task left. :ahhh
-
The list is going well got about 10 tasks left

Going to test the can opener tomorrow
-
I'm pretty well along on my list too

Haven't done the tasks with the can opener, the second ones with the bit grip and driver, the large, small and eyeglass screwdrivers, the wire cutting and the ruler yet, the rest is checked off.
-
Day 11 - continued
Decided to check some more tasks off the list. In sequence:
Had a cable with a cigarette lighter plug with a blown fuse. Used the appropriate bit in the plier grip to open the plug.
While I was at it, I decided to test the wire cutter on some chicken wire I had lying around, no damage to the cutters, then to bend it at a pretty sharp angle, where the compound leverage helped a lot. (Pics are swapped around, sorry...)
In the last pic I cheated by using the medium Phillips bit via a bit driver extender on the adaptor and bit diver stub to fit a maglite clamp. The 90° position is great and the amount of torque you can bring to bear is a pleasant surprise.




-
The list is going well got about 10 tasks left

Going to test the can opener tomorrow
I did some research and found a few canned products with small circumferences. Just got to go buy them.

I found some old style cans today
Bought 3 cans 2 normal size and 1 large size
And will open all 3 tomorrow and use
the contents of the tins for pudding

-
You guys are well ahead of me........ :-\
But I'll catch up!

-
Day 06:
Used the PAD's medium driver (cap lifter) to remove and replace a light switch cover with a solid cover. No issues with the driver for this light-duty task.

For the checklist, I used the serrated blade to cut through some webbing. This webbing is 5cm wide--according to the PAD's ruler--and is doubled over. The serrated blade cut this fairly easily, but I had a bit of a tearing impression. I cut it a few times just to test it out. The width of the material makes this a bit of a difficult task, but I think the SOG did well here. I have the impression that the serrated blade would make a good emergency rescue tool for getting out of a seat-belt or harness.

-
I'm going to be doing some car camping up in Glacier National Park and/or northern Montana over the next couple of day. So, I may be a bit tardy posting up my required photos for the next few days.
But, rest assured, the PAD is going along and will continue to serve as my primary tool (Vic Classic is back-up). Hopefully I'll have some decent photos to share from the trip.

-
Sounds fun Nix
Hope you have a good time
Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login