Access to Power -SOG 30-day Challenge! Starting June 1st! Access & Access Deluxe
-
I'm pretty well along on my list too

Haven't done the tasks with the can opener, the second ones with the bit grip and driver, the large, small and eyeglass screwdrivers, the wire cutting and the ruler yet, the rest is checked off.
-
Day 11 - continued
Decided to check some more tasks off the list. In sequence:
Had a cable with a cigarette lighter plug with a blown fuse. Used the appropriate bit in the plier grip to open the plug.
While I was at it, I decided to test the wire cutter on some chicken wire I had lying around, no damage to the cutters, then to bend it at a pretty sharp angle, where the compound leverage helped a lot. (Pics are swapped around, sorry...)
In the last pic I cheated by using the medium Phillips bit via a bit driver extender on the adaptor and bit diver stub to fit a maglite clamp. The 90° position is great and the amount of torque you can bring to bear is a pleasant surprise.




-
The list is going well got about 10 tasks left

Going to test the can opener tomorrow
I did some research and found a few canned products with small circumferences. Just got to go buy them.

I found some old style cans today
Bought 3 cans 2 normal size and 1 large size
And will open all 3 tomorrow and use
the contents of the tins for pudding

-
You guys are well ahead of me........ :-\
But I'll catch up!

-
Day 06:
Used the PAD's medium driver (cap lifter) to remove and replace a light switch cover with a solid cover. No issues with the driver for this light-duty task.

For the checklist, I used the serrated blade to cut through some webbing. This webbing is 5cm wide--according to the PAD's ruler--and is doubled over. The serrated blade cut this fairly easily, but I had a bit of a tearing impression. I cut it a few times just to test it out. The width of the material makes this a bit of a difficult task, but I think the SOG did well here. I have the impression that the serrated blade would make a good emergency rescue tool for getting out of a seat-belt or harness.

-
I'm going to be doing some car camping up in Glacier National Park and/or northern Montana over the next couple of day. So, I may be a bit tardy posting up my required photos for the next few days.
But, rest assured, the PAD is going along and will continue to serve as my primary tool (Vic Classic is back-up). Hopefully I'll have some decent photos to share from the trip.

-
Sounds fun Nix
Hope you have a good time
-
**Day 06 **(continued):
I'm taking a small daypack on the trip. I decided to attached the SOG sheath to the pack using MOLLE attachment points.
The Blackhawk clips make attaching it quick and simple. And I think a bit more secure than just the one snap. The Blackhawk clips can fail, but I've never seen them do so. I do have some more secure MOLLE attachment clips, but they tend to be a pain to use, so the Blackhawk clips make a good compromise.

You can see the tip of the clip peeking up in this next photo. And you can see how the velcro closure flap on the sheath sits off at an angle when the bit set is also stored in the sheath.

-
Looking forward to seeing how the PAD does for you out there, Nix!

-
I am not, usually, one to rock the boat. But, curiousoty got the best of me today.
I made a crappy video (three parts, because I suck at youtube) about the file. If you dare to see what happens with the file, please feel free to watch. :)
Part 1:
https://m.youtube.com/watch?v=ls5kkgQ_RKY
Part 2:
https://m.youtube.com/watch?v=p_muxRa6jXE
Part 3:
https://m.youtube.com/watch?v=mYvZ5EsPaA4Apologies for the video being crappy. I am not a youtube person. :ahhh
Edit: I think that qualifies as using the file. One more checked off. And I just realized I hadn't used the medium driver yet! Will do that one tomorrow.

-
Nice test GLBM

I will try that and use the file from the LM Supertool
For comparison and take some pics
-
@Nix said:
You guys are well ahead of me........ :-\But I'll catch up!

have a very nice trip!

Thanks GLBM

The cutters still work perfectly
I haven’t had any problems with cutting
not that I didn't tell you, before cutting the nail, that your cuters would probably be damaged like my SOG PL suffered, and I even provided pics of the damage on mine!
which was very similar to what happened in your PAD cutters.As a side note, I watched some reviews on the PowerPint and it looks like the same problems (semi bad locks with wiggle, horrible scissors as typical from SOG, etc.) that other modern SOGs have are still there, :P
but surprisingly the blade on it seemed very good compared to that of the PAD,

and the file seems to be excellent!! :ahhh :D So it seems that even newer Chinese SOGs can have good, working files and not this pseudo-nail scraping implement ::) As to why SOG didn't put it in this tool, who knows ??? -
@Wspeed said:
Nice test GLBM
I will try that and use the file from the LM Supertool
For comparison and take some pics
Thank you, W! I look forward to reading your report.

As far as the file on my particular PAD goes, I have had to admit that I stuck my foot in my mouth in public. It is pretty embarrassing.

It is in no way a "good" or even "mediocre" file, but (at least in my case) it did work. :ahhh -
Nice test GLBM

I will try that and use the file from the LM Supertool
For comparison and take some pics
Thank you, W! I look forward to reading your report.

As far as the file on my particular PAD goes, I have had to admit that I stuck my foot in my mouth in public. It is pretty embarrassing.

It is in no way a "good" or even "mediocre" file, but (at least in my case) it did work. :ahhhI am really surprised that you got the file to work
And I want to test the file on aluminium
As you tested mild steel and wood with ok results
I will see if I can do the test tomorrow
-
Spoiler:
I am not, usually, one to rock the boat. But, curiousoty got the best of me today.I made a crappy video (three parts, because I suck at youtube) about the file. If you dare to see what happens with the file, please feel free to watch. :)
Part 1:
https://m.youtube.com/watch?v=ls5kkgQ_RKY
Part 2:
https://m.youtube.com/watch?v=p_muxRa6jXE
Part 3:
https://m.youtube.com/watch?v=mYvZ5EsPaA4Apologies for the video being crappy. I am not a youtube person. :ahhh
Edit: I think that qualifies as using the file. One more checked off. And I just realized I hadn't used the medium driver yet! Will do that one tomorrow.
Thanks for taking the time to record and upload these.

-
Great challenge and pics guys [emoji16] And good idea with the checklist [emoji106]
Sent fra min FRD-L09 via Tapatalk
-
Spoiler:
I am not, usually, one to rock the boat. But, curiousoty got the best of me today.I made a crappy video (three parts, because I suck at youtube) about the file. If you dare to see what happens with the file, please feel free to watch. :)
Part 1:
https://m.youtube.com/watch?v=ls5kkgQ_RKY
Part 2:
https://m.youtube.com/watch?v=p_muxRa6jXE
Part 3:
https://m.youtube.com/watch?v=mYvZ5EsPaA4Apologies for the video being crappy. I am not a youtube person. :ahhh
Edit: I think that qualifies as using the file. One more checked off. And I just realized I hadn't used the medium driver yet! Will do that one tomorrow.
Thanks for taking the time to record and upload these.


@Wspeed said:
I am really surprised that you got the file to work
And I want to test the file on aluminium
As you tested mild steel and wood with ok results
I will see if I can do the test tomorrow
I look forward to reading about your experience with SOG-filing aluminum. Primarily, because it clogs(for my lack of a better term) even the best files in short order. :ahhh
Whatever the results, please don't <u>file</u> them away. :D
-
Yes this could be interesting to see what will happen
I am going to use the LM Supertool file for comparing
The SOG PAD file on the same aluminium
This way I will have a better idea if the file works or not
Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login