Noa's fixed blade challenge
-
Day6
So today I decided to do a cut test. In particular I decided to use the push knife as intended on a cardboard target. The result is 5 layers of penetration and skinned knuckles.
This highlights an inherent problem with the design. When you punch even with light force this type of knife torques in your grip causing the shoulder of the blade to impact the back of your knuckle.
Very few manufacturers bother to smooth out the tang or that back shoulder. I already knew this cheap one was sharp as a cheese grater, but I've seen expensive ones just as bad.
All that said this is a "get off me" knife for when you already have lost the fight. Busted Knuckles probably aren't your biggest concern compaired to a busted head.Please note that cut doesn't look near as bad in the pic as it did in real life. It hasn't really started bleeding, I took about a 1/4in slice out of the top of my finger. But I knew this would happen and have had much worse from these. The worst one I've had skinned both knuckles and inbetwene the fingers on ether side of the tang

-
@Noa Isumi said:
Day6
So today I decided to do a cut test. In particular I decided to use the push knife as intended on a cardboard target. The result is 5 layers of penetration and skinned knuckles.
This highlights an inherent problem with the design. When you punch even with light force this type of knife torques in your grip causing the shoulder of the blade to impact the back of your knuckle.
Very few manufacturers bother to smooth out the tang or that back shoulder. I already knew this cheap one was sharp as a cheese grater, but I've seen expensive ones just as bad.
All that said this is a "get off me" knife for when you already have lost the fight. Busted Knuckles probably aren't your biggest concern compaired to a busted head.Please note that cut doesn't look near as bad in the pic as it did in real life. It hasn't really started bleeding, I took about a 1/4in slice out of the top of my finger. But I knew this would happen and have had much worse from these. The worst one I've had skinned both knuckles and inbetwene the fingers on ether side of the tang
yeah cheap push knives do that. I have had a few with design issues, all were crappy cheap blades. 
The only one I know for sure that is extremely comfortable in the palm, fingers and has nice corners is the real deal, that is, the Cold Steel

-
Day7
Cardboard cutting....FAIL
Anyone who's seen my 30 days cutting this single cardboard is daily task for me, and I do it every challenge. This is the first time I have ever had truly fail in cutting this stuff no matter how cheap it may be. As you can see it didn't really cut so much as it ripped. I could honestly get cleaner cut folding and tearing it.

-
cute little knife, but not really a cutter, designed for poking, plunging and twisting.
But, then to be fair, I got hung up in post cutting a roast beef sandwich for the dog. What did the dog do to upset you. That isn't actually roast beef, and then the bread is not the best for dog's diet either.

Your challenge is a tough one, carrying a fix blade for 30 days has my respect. All the best.
-
Day8
Carrying a fixed blade was a lot easier when I lived in the country. Now that I'm in an urban environment I have to be a bit more careful lest I offend someone.
It used to be nothing for me to walk around with a Buck on my hip. The only time I ever got looks was when I walked into a gas station with a Cold Steel kukri machete on a drop leg.
All that said; I regularly carry a 4in RCF Hunter on my days off and my Glock 81 is always in my edc backpack.
Truth is I'm probably going to switch out to that RCF Hunter here in a few daysAs for the sandwich: yeah I know junk food generally isn't good for them but a half a plain sandwich as an occasional treat is ok. ( provided you avoid certain foods and sauces that are actually harmful or poisonous)

-
Day9

-
Been meaning to keep up with this better
been so busy the last while :ahhh Great pics Noa

-
Day10...oops put 9 origonaly

Ok so today is more kitchen prep. Today I am using the RCF. The 1/4in thick blade is a bit chunky for fine slicing but the hollowgrind helps.
Unfortunetly I am still experimenting with this little grill, havent used a Lodge Sportsman in years. Too many coals last time, not enough this time. I got the franks and chops done (barely) but the chicken had to be baked. It is odd downsizing from my old pit to a cast iron hibachi like I used 15-20y ago. Mabey next week I will get it right.
I will proabably finish out the month switching back and forth between this and the glock knife.



-
Day11
A size comparison.
Vic Trekker, RCF Hunter, Glock81 Field knife, LM ST300The RCF is 1/4in thick D2 with Micarta and a hollow grind. It came with the leather pouch and the kydex one was the 1st Kydex I did a couple years ago. I like the high ride and teclock on the kydex, but it is a bit tacticool; so if I cant cover it I use the leather one.
The Glock is the field knife varient of the sawback AUG bayonet. From what I understand the rear lug is still there, they just press a cap over it. This one rides in my edc bag.

-
nice to see you're still going strong
-
Day12
Today I was wearing the RCF in the Kydex. One thing that I'd like to point out is that this knife is actually just small enough for me pocket carry too. And that's one of the beauties of the way I have two kayaks setup with a tek-lok. I can pop it off my belt and just drop it in my pocket when I need to have it concealed, like at work.
This works with any pants that have reasonable pockets. On pants with the short trouser cut pockets such as Dickies the top inch of the handle sticks up.
You may also notice I have to knife flipped edge forward instead of back, this is just to make sure it stands upright in my pocket rather than tip back and have the handle exposed.

-
Stupid voice type
"The kydex" became a pair of boats"And that's one of the beauties of the way I have two kayaks setup with a tek-lok"

-
Day13

-
Day14

-
Day15
Cutting down a cheap yoga mat to use as a pad under the guest kennel/crate to keep it from scratching the floor.Edit:
I didn't realize just how bad the color was in this photo. No flash and the only light source is a LED mock Edison bulb. We all know the Glock fde and that yoga mat is supposed to be a fluorescent Green
-
More great pics and uses Noa

-
Day16
Starting to organise...barely make a dent.Pics
Before
After
After
AfterIts a start




-
@Noa Isumi said:
Day16
Starting to organise...barely make a dent.Pics
Before
After
After
AfterIts a start
very cool start!!
Regarding the last pic, may I ask you a few questions about the collection?
Ignore them if you don't have time or patience :DSpoiler:
- Is that a Lighting OTF that I see sandwiched between the orange and wooden handled folder?

- And the one with "camo inlays" on the bottom box? It has the glass breaker of Microtechs but doesn't look like one to my eyes

- All to the bottom right, next to the blue stiletto, is that an Emerson?
- on top there is a Gerber mini box and an orange folder, does that foder have a "wave hook"? ???
- on the far right there appears to be a Svord folder, a Piranha multitool and a small KaBar neck knife,

you have interesting pieces there!

- Is that a Lighting OTF that I see sandwiched between the orange and wooden handled folder?
-
I need to get more boxes and something for my fixed blades. Right now I have a lot of coppies and counterfits which is kind of amusing. I actualy need to seperate the real from the fakes. I have no clue how many knives I actualy have here let alone in storage with my shop equipment. I know MrPinchy, Gerber Bolt Action, and some swords are there.
1&2 the "lightning otf" and the camo "microtech" are both low quality knockoffs(compleatly diffrent but we'll use knockoff). All the knives in those 2 compartments are autos; except that orange handled 2blade hacksaw
3 the Emmerson is a counterfeit of a Comander 1 and is actualy really good quality. As far as a build grade I would say it is as good as the Kershaw production models.(I have a cqc6k) I got this as part of a bulk lot in '02 and cant find another or who made it. It has no markings other than "made in china"
4 the orange folder has a double guard flipper. It is one of TacForce's little spear point rescue knives.
5 yes that is a piranha, svord peasant in black plastic, and MTech mini-Kbar neck knife(dont buy knives drunk kids)
I got the piranha intending to remove the blade and have a cheap TSA safe multi, but never did.Edit:
Well I think I just found the limit of the springs in the camo otf. It went out and is not just derailed but compleatly dead. Actualy thinking about it the locks should still engage even if the drive springs are messed up. This will be intresting to take apart and see what happened. That is what I bought it for in the first place, to see the guts of a DAOTF.


-
I need to correct myself on the "emmerson" clone;
That grip is diffrent. I remember looking it up years ago and thinking it was a dead ringer for one of the comanders varients, now I look them up again and nothing looks the same.
Of course its too late to edit again.

Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login