DIY diamond file?
-
The tungsten carbide alternative was interesting. It is so heavy that one might possible just submerge the surface in question horizontally, dross on some carbide, plate some, dross some more, plate some and so on.
-
This might sound stupid but how hard would it be to mod a file from a Wave? There's a guy on here who sells parts from LM. Might be a lot easier way of doing it.
-
@Vidar said:
The tungsten carbide alternative was interesting. It is so heavy that one might possible just submerge the surface in question horizontally, dross on some carbide, plate some, dross some more, plate some and so on.I was thinking keeping the steel horizontally with diamond dust sprinkled on during the elekctroplating process. Though, how to make sure that the diamond particles simply do not fall down and are embedded, held firmly in the steel?

-
@ddogu said:
Well, I wanted to go that way, too but you know Vidar. He and his watermelon shells got me...Again, I'm sooo sorry! I didn't even know me and my melons had such impact.. :D
@ddogu said:
I was thinking keeping the steel horizontally with diamond dust sprinkled on during the elekctroplating process. Though, how to make sure that the diamond particles simply do not fall down and are embedded, held firmly in the steel?
I don't think there are any risks of the diamonds or tungsten getting into the steel itself? And hopefully the plating will attach only to the steel and other plating, so the diamond or tungsten particles will be surrounded but keep sticking up. If not one might have to use a file to get to the file? :ahhh
I think I have most of the stuff needed to try laying around here somewhere. Should have an acid bath for cleaning too, but not quite sure where I put it. Plating to hold stuff might need to be thicker and stronger than plating just for weather proofing or decoration, so that might require some differences in approach. I guess spare time and some nickel anodes or ready nickel solution is what I miss to be able to try.
-
A little water melon shrinking update. After some more research into this it seems to be a fair chance that diamond files in multi-tools are made by vacuum brazing rather than electroplating. (Electroplating giving more aggressive files, but are also more prone to wear while filing metals and the like).
I have a vacuum thingy, and a brazing capable oven, but not a vacuum brazing oven... :-\
I might still get some diamond powder and try electroplating it just for the smurf of it. If it is 70-90% as good as bought that might be nice enough - especially as one should be able to redo the diamond layer many times as it gets worn. I'll put it on the rather long to do list.
-
There is more than a fair chance this will be an spectacular failure but I've gone ahead and ordered some tungsten carbide file grit material. It should have a few less worries than diamond grit. My first (very) basic plan of attack is to just have it in a little bath of melted nickel on a suitable piece of steel. Cleaning and surface tension might be issues, as might adhesion between both steel and nickel, and nickel and tungsten, but I'm hoping this is one those things that just magically works out great! ::) (Someday something has to - right?)
Time will tell. Worth a shot I figure :)
-
Lowes used to have a set of hobby files (half were diamond files, the other half regular) with 1/4 hex shafts so that a screwdriver handle could be used as the handle for them. I suspect you could use that with a multitool with a 1/4 driver on it. Maybe grind them down for Leatherman flat bits.
-
Sorry for not reading every single word on this thread... time is of the essence :D
But did someone mention the replacement kit for the LM Surge blade exchanger already?
It's a woodsaw and a two sided file (diamond and normal).
Greets,
Matt
-
@MTMatt said:
Sorry for not reading every single word on this thread... time is of the essence :DBut did someone mention the replacement kit for the LM Surge blade exchanger already?
It's a woodsaw and a two sided file (diamond and normal).
Greets,
Matt
Well, I did.. It's $5 replacement a pop.. But the something to do with Melons got over them.. Hey but here is all about experimentation right?

-
Okeedokee... seems the melons passed me with no harm :D
-
@Sam Lim said:
Well, I did.. It's $5 replacement a pop.. But the something to do with Melons got over them.. Hey but here is all about experimentation right?
There were some monkey brains too? Of course if one simply wants a file the very rational choice is just buying one.
Either way I figure it might be interesting to try a bit of a DIY angle. Having the option of putting tungsten carbides on steel surfaces might come in handy in a few ways, and not just for files. On the flip side I guess the potential downsides are limited to setting fire to myself or the workshop, catching a sputter boiling nickel ball in the eye, breathing poisonous heavy metal gases, wasting some time and money on this.. If it goes amazingly wrong I might at least learn something. Time will tell.

Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login