Show off your Sak mod's!
-
Hi guys!
A minor mod on my Electrician. I love having a small blade, but I miss the Phillips of the Pioneer. So I took my Dremel 3000 and turned the big flat driver into a 2d Phillips/small flat.
It works nicely. You can see the result compared to the original, and to the can opener / driver.
I'll do the same on my Rancher and Harvester.


Στάλθηκε από το HUAWEI VNS-L31 μου χρησιμοποιώντας Tapatalk
-
My bladeless B&B SAK got some new clothes

[It's not failure if you learn something from it]
-
@kottskrapa said:
My bladeless B&B SAK got some new clothes
[It's not failure if you learn something from it]
Lots of forest in Sweden.... don’t lose it. :ahhh :D
-
Did this (screws and epoxy) but it don't stick. Second try I made the glue area folder with dremmel. Still no luck. Any advice is welcome!

~ i love whittling and SAK's ~
-
@Don Pablo said:
My bladeless B&B SAK got some new clothes

[It's not failure if you learn something from it]
Lots of forest in Sweden.... don’t lose it. :ahhh :D
Im living in the middle of it. But this is for those times Im going to town to get some beers with friends and a blade are not appropriate [emoji5] but barbecue in a park might be dangerous
[It's not failure if you learn something from it]
-
Well this is awkward...
I had finally decided to buy some pivots and screws from Alpha Knife Supply, but due to the whole GDPR deal, EU residents, without a previous account in the site, are banned...[emoji36]Anyone from that side of the pond would be willing to make a purchase for me? Please contact me by PM.

Sent from my Mi A1 using Tapatalk
-
@FInixNOver said:
Well this is awkward...
I had finally decided to buy some pivots and screws from Alpha Knife Supply, but due to the whole GDPR deal, EU residents, without a previous account in the site, are banned...[emoji36]Anyone from that side of the pond would be willing to make a purchase for me? Please contact me by PM.

Sent from my Mi A1 using Tapatalk
Ended up going with the pivots and screws from KnifeKits...
I know the tolerances are not as good, but I want to upgrade my daily SAK to pivots/screws.
Now, to complete this upcoming mod, I'm searching for a magnifying glass layer, but would like to avoid having to buy an Explorer just for that.
Anyone have these parts for sale?And to finish, one question...
What's the thickness of the magnifying glass layer? The idea is to incorporate it in an Alox SAK, therefore, I need to find out which backspring I need to use to make this happen.Sent from my Mi A1 using Tapatalk
-
@FInixNOver said:
What's the thickness of the magnifying glass layer? The idea is to incorporate it in an Alox SAK, therefore, I need to find out which backspring I need to use to make this happen.It's the same thickness as a Pioneer blade layer, whatever that is.
-
What's the thickness of the magnifying glass layer? The idea is to incorporate it in an Alox SAK, therefore, I need to find out which backspring I need to use to make this happen.
It's the same thickness as a Pioneer blade layer, whatever that is.
Nice! And thanks for the answer!!
I have a spare of those.Sent from my Mi A1 using Tapatalk
-
What's the thickness of the magnifying glass layer? The idea is to incorporate it in an Alox SAK, therefore, I need to find out which backspring I need to use to make this happen.
It's the same thickness as a Pioneer blade layer, whatever that is.
So you don’t need two of those blade springs?
Today I learned.
-
For just the phillips/magnifier in a single layer, no. If you're putting the phillips opposite the can opener/cap lifter pair then you need 2 x opener layer springs.
-
My configuration will be the following:
Layer 1 - Blade and Awl
Layer 2 - Scissors
Layer 3 - Magnifying glass and Phillips driver
Layer 4 - Cap lifter and Electrician bladeSent from my Mi A1 using Tapatalk
-
Remember that you will have to drill out the tool pivots to fit the thicker alox rivets. :ahhh
-
@Don Pablo said:
Remember that you will have to drill out the tool pivots to fit the thicker alox rivets. :ahhh
Already have ordered carbide drill bits for that. [emoji16]
Sent from my Mi A1 using Tapatalk
Mag glass will sit really high if you dont make a small recess in the spring for it to fit into. You dont have to do it, but it fits so much better that way.
-
@Don Pablo said:
Remember that you will have to drill out the tool pivots to fit the thicker alox rivets. :ahhh
Already have ordered carbide drill bits for that. [emoji16]
Sent from my Mi A1 using Tapatalk
Mag glass will sit really high if you dont make a small recess in the spring for it to fit into. You dont have to do it, but it fits so much better that way.
That's actually a great tip!! I'll keep that in mind.

-
@Don Pablo said:
Remember that you will have to drill out the tool pivots to fit the thicker alox rivets. :ahhh
Already have ordered carbide drill bits for that. [emoji16]
Sent from my Mi A1 using Tapatalk
Mag glass will sit really high if you dont make a small recess in the spring for it to fit into. You dont have to do it, but it fits so much better that way.
That's actually a great tip!! I'll keep that in mind.

Mail call today.
Received the donor Explorer for the mag/phillips layer and the pivots and screws from KnifeKits.
Taking into account what I've read in the past, I was quite surprised to see that the pivot's tolerances we spot on.Now I have another question... Would it be acceptable to use 3.2mm (0.126in) drill bits, which are available in my local hardware store, to enlarge the tool/backspring holes, or will I be better off with the 0.125in drill bits that I've already ordered?
About the Explorer SAK, there's an engraving in the main blade "Arnaud B."
Does this mean anything to anyone, or can I go ahead and disassemble it?

Sent from my Mi A1 using Tapatalk
-
Finally received the carbide drill bits.
After receiving the wrong product from one seller and placing a new order to a different seller, here they are and I'll be able to resume the pivots/screws conversion!

Sent from my Redmi Note 5
-
Wenger Compact Motorist (original plan was to make a Wenger Trail Guide...)
-
That's a cracker mate.

Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login