The Great Multi-Tool Restoration Thread!!!
-
Oooh my kind of thread

Okay, here is a Gerber (I don't even know what model it is) that I got off ebay for next to nothing.
The seller was very honest about the state of it, and when it arrived, the blade was swinging loose, and the the pliers and many of the tools were seized and very difficult to open.
So I stripped it down, and was very impressed at how easy that was to do, using bits that I actually had in my bit set for a change, and a driver I got from some place on the net ;) The following picture shows the tool in the latter stages of reassembly, I didn't think to get any "before" pictures, but it was horrible.

I used various methods to get the thick gunge out of every nook and cranny, including immersing in coca cola (it really works as a degunger), and reassembled with a bit of care as to tension of screws to give a tight, but not over tight resistance to each of the components. Obviously, there wasn't much I could do about the "missing" BO coating, but a few strokes of the blade on the sharp maker, and it turned out like this:


This little tool has had a tough life, but for light duties around the house, it will live a little longer. I even managed to clean up the sheath

-
Awesome, this thread is going to be fun! :D Nice job on the restoration, Dave!

-
is this for tools that we fix or can we add ones that we send out and bring back to life?
-
Good idea for a thread
Great job on both the Gerber's guys 
-
@RaptorMan said:
is this for tools that we fix or can we add ones that we send out and bring back to life?I think it should be for all restoration projects.

-
Great work boys :tu
-
Great thread GG

-
Looks like another multiplier that Dave.
I agree, great idea John.

-
In the words of the great Des Lynam:
"Niiiiiiiiiiiiiiiice"
-
According to this thread, it looks like mine is a close match to a "type 3" on the Bob scale!
-
nice thrad
I took the broken serrated blade out of a gerber and replaced it with a bear jaws lanyard, I figured it was better than nothing -
@DaveK said:
According to this thread, it looks like mine is a close match to a "type 3" on the Bob scale!Maybe actually a "type 4" Dave? (due to the round nuts on the blade pivots)
-
Yup, I think you're right actually, in fact that's the pic I copied initially, before losing the plot somewhat :P
-
-
Lol. That is dangerously close to the truth actually.
-
I dismantled a Gerber MP600 yesterday, on the thinly veiled premise that it needed restoring ;)
It did have a bit of gunge and rust though, and it cleaned up easier and better witht the pliers removed. I couldn't figure out how to remove the handle tools though, so I might go back and do that again at some point.
Looks good now and I'll post some pics later.
-
@DaveK said:
I dismantled a Gerber MP600 yesterday, on the thinly veiled premise that it needed restoring ;)It did have a bit of gunge and rust though, and it cleaned up easier and better witht the pliers removed. I couldn't figure out how to remove the handle tools though, so I might go back and do that again at some point.
Looks good now and I'll post some pics later.
There should be one side of the handle where the "blot" head sticks up more, grab this with a pair of pliers and turn. Simple as that :) The other side shouldn't move as it is recessed into the handle :)
-
Maybe not a restoration , but a good tune up :D :D. My terrific Kershaw A100 that I got from Neil in a 3 way trade , was 95% perfect , it's only blemish was the main blades linerlock did not fully engage properly :(. I tried hard too ignore it , but in the end I could not help my self ::) :D :D.
[(http://i291.photobucket.com/albums/ll287/multimat426/vise/c6ee18f6.jpg)]
](http://
[(http://i291.photobucket.com/albums/ll287/multimat426/vise/418da612.jpg)]
](http://The Confined Nut(No not me :D :D)[(http://i291.photobucket.com/albums/ll287/multimat426/vise/446e9ae3.jpg)]
](http://
Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login
