Access to Power -SOG 30-day Challenge! Starting June 1st! Access & Access Deluxe
-
Excellent looking mushroom soup Nix

-
Day 17
Today I am removing my old bike battery
As over the winter the battery stopped working completely
So I used the 1/4 inch driver with the adapter
and the largest cross head screw driver from the bit kitNo problems undoing the battery terminals
I really lik the PADs 1/4 inch driver and bits set
And it looks a nice quality toolNow I am waiting for the new battery to fully charge
Before I can fit it to the bike



-
Great use, Wspeed.
I had a bike's battery die on me whilst I was on a road trip. I was in a remote area and it was quite a bit of work to get back to a town where I could order a new battery. I was sure glad to havve a few tools with me that day!
Once a bike's battery gives up the will to spark, there is no bringing it back. :(
-
I had a bike's battery die on me whilst I was on a road trip. I was in a remote area and it was quite a bit of work to get back to a town where I could order a new battery. I was sure glad to havve a few tools with me that day!
Once a bike's battery gives up the will to spark, there is no bringing it back. :(
I am glad my bike was in the workshop
when the battery stopped working
More money spent this month :ahhh
I would not be happy if that happened when out on the bike :ahhh
Lucky that you could order a new battery Nix
-
It looks as if we are <u>pad</u>ding the results here. :D
O.k. I'll go back to my <u>pad</u>ded cell now.

-
@gerleatherberman said:
It looks as if we are <u>pad</u>ding the results here. :DO.k. I'll go back to my <u>pad</u>ded cell now.


-
Day 12:
Checklist challenge!

Show yer checklists today:

-
Checklist Day 17


-
Most excellent progress on your lists, gentlemen!

I am fairly close to completion. But, I am dreading the can opener testing. I can buy my diet Coke in the old-style glass bottles to try the cap lifter on though. :ahhh

-
Day 12 (continued):
Used the PAD and bits to tighten up a loose drawer handle in the kitchen. Worked well!


-
D_T.......checklist?......

-
Checklist? What checklist?
Just kidding... pretty well along actually, only have a few items left, including the small screwdriver and all the can opener actions (for lack of suitable cans). I have the checklist at the office so can't show y'awl right now.
On Day 17, again, not much use, although the PAD has been in my pocket all day. So here's a beauty shot with a somewhat recognisable theme. I'll do better soon, I think, some days off coming up.

-

....but don't wear out that cap-lifter too quickly!

-
At this point, D_T has used the cap lifter so much, it may qualify as abuse.

J/K :PDay 17. Thought the #1 phillips in the handle would wotk, but it was actually too big for these screws. Used the adapter and mini phillips bit to tighten the hinge screws on the doggie barrier to the dining room. They get loose from moving the barrier around fairly often.

-
**Day 12 **(continued):
Another little bit of disappointment.....
I wanted to cut a small length of hi-vis mono-filament line this afternoon. I thought nothing of opening up the PAD to use the wire snips to cut this 30# mono. The mono is fairly stiff and resembles fine wire, so I expected the PAD to snip it easily.
But....NO.
I was a bit surprised that the PAD merely folded the mono, and didn't cut it.
What? I tried again. And again. Same result. The mono just folded up.
Now, I thought I had snipped mono in the past using the wire snips on a multitool, but, you know, I may have forgotten the truth. Still, I was a bit freaked out that I may have had a false memory.
Could I really be that wrong?!?
So, I rummaged around and dug out some other multitools to test:

As you can see (look carefully now), my Charge, Rebar, and Spirit all cut the mono cleanly and easily. If pressed, I'd say the Rebar did the best job. The Spirit was a bit fiddly because the run of wire cutting edges is small and required more focus. However, if aligned properly, the Spirit did the job easily and precisely.
The PAD, not at all. See the photo above where the mono is just folded up in the PAD's jaws.
Not shown: I also tested a LM Skeletool. Yes, it also snipped the mono easily. I used the mono to fashion a short lanyard on the PAD in anticipation of going fishing. I'd like a very positive attachment to avoid losing this PAD. I think.

The Skeletool was super-useful for snipping the mono after tying knots in order to remove the tag ends.
Good thing I didn't need the lanyard attached to the Skeletool........... >:(
-
Guess I should add a shot of the new lanyard:

If you look closely, you'll see a small snippet of mono that the Skeletool cut off the final knot.
Yeah, I said 'Skeletool'.
-
:o
It is disturbing to learn about the cutter issue, but that isn't uncommon for a lot of MTs, from my experience. Will it cut small steel wire or electrical cord?
I would have expected this on Wspeed's and powernoodle's PAD(nail abuse test) to be more likely to have this issue.
Is the inability of the cutter consistent for the length of the cutters? Or just a portion(#edit: exactly where you pictured it)?
Sorry to ask so many questions, but your experience has me curious as to my PAD cutter's abilities. I do intend to check mine for issues at some point.
Now, with that said, I have experienced this issue with fine electrical wire on; one of my old(USA) SOG PowerLocks, one of my two Waves, my supertool 300, my swisstool, and several Gerber's(the replaceable cutter kind). The Wave being the worst of them(it couldn't even cut 18-2 lamp wire properly). LM did fix it with a new plier head, but dang, it was a brand new wave. While a majority of my MTs have little to no issue cutting fine electrical wire, I am not really surprised anymore when I encounter it. :P
To be honest, I am not familiar with the material you are cutting. Where about does it land in a chart between basic fishing line and thin string trimmer line(#80 or so)?
Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login
