Skeletool owners club
-
-
Thank you gentlemen!

-
@JustinCase said:
Got the Damascus blade in trade for one of my flashlights so I decided to do some mix and match between the CX vs REI and this is what eventually happened at the end of a process.. :D

a most excellent shot!!
And that Skele is no slouch either

-
SkeleCool ! 8)

-
Thank you Peacent and Steve

-
Well, got a new Skeletool CX.
Used to carry one from ~2010 as my main EDC - until I gifted it (a spur of the moment kind of thing); held out for almost 3 years, but going about without an MT by my side got to be too much in the end, so I finally ordered a new one from leatherman.ca.
Got it three days later (VERY fast, by Canada Post standards - probably because it was shipped with Purolator :)), and got to fixing the obvious faults; you must know what I mean - when you get a tool you intend to carry with you every day, you want it to be as close to perfect as possible.
So, filed off the imperfections in pliers casting (there was some flash left over that interfered with the springs on the bit driver side when opening/closing pliers; made blade OHO hole smoother (I think the die they use is past its prime). Left alone the 'pliers don't meet at the very tip' issue (they meet at the third micro-serration instead) - though annoying, I doubt it will be an issue in actual use.
BUT.
I'm looking at the thing, and it just looks wrong. Took a while to figure it out, but I got there in the end - turns out they did away with those huge countersunk washers and screws arrangement that attach handles/blade to the plier head; it's just screws with large heads now, instead. I only noticed it because they're not polished (looks dull, almost like aluminum). I never imagined that hardware could change the look of the finished item so much, but here we are.
My explanations are usually crap, so here's a picture:

I sure do wish I had my 2010-dated skeletool CX now... Of course, this won't affect functionality in any way, but, man! the tool sure does look cheaper for it.
BTW, the one I just received is stamped 0817.
(I also ordered a Crunch - always wanted one, and finally decided to get it; and since I've nothing to compare it to, I'm sure it'll be fine... Right?)
-
Welcome to
Sorry to hear it isn't as nice as the older ones :-\ but the Skeley CX and Crunch are 2 very great (completely different) tools and I am sure you will love the Crunch 8) 
-
Thanks, Poncho65 :) I'm sure Crunch will not disappoint.
-
Thanks, Poncho65 :) I'm sure Crunch will not disappoint.
well, one thing I know for sure about the Crunch, both its blade and its jaws have no point :D
Nothing's quite like a pun to get your point across :)
-
Had to send of my Skeletool for repair. The actual frame broke at clip. (Wish I had pictures, I was in a rush and just wanted it back since it is EDC). The actual blade also had chipped a few millimeters after the serration started. I use it to cut open boxes and light use so I was a little disappointed. I picked it up a Home Depot for $15 and another for $8 (a week later) on clearance so I can't complain too much. (Gave the second to my brother). Love the weight and the size. Thought about getting the bit pack for it, but for now just waiting for it to be sent back to me...lol. Wearing my GI Gerber 600 for now. About kills me because you have to open the Gerber for EVERYTHING. I could access the knife from the skeletool without opening the pliers which is a must for me.
-
Welcome to
JS
Sorry to hear that about he Skeley :-\ I am sure LM will take care of you and turnaround time is usually pretty good from them as well 
-
Bummer! :P
sorry about your Skele, but what were you doing to break it? ??? I ask because the Skele is known to be weak and a light use multitool, and if you're used to the MP6000 by Gerber they are in no way similar as to what they can handle and the forces you can apply to them

But at $15 or $8 I'd have bought **all **the Skeletools in the store!! :ahhh
-
On my job i pickup a ton of heavy products. I actually had it clipped inside my jeans and picked up about 100lbs of product held it at my waistline.. I felt a pop when I lifted it, but didn't think nothing of it. So later on I pulled it out of my pocket and thought the clip seemed really loose. So I thought it just needs tightening.. I went to tighten it and a piece of frame when with it.. Not sure about the chip out of the blade..I use it to cut nylon straps. I mostly use it as a knife, but I started using the bits more and more..
I guess this is the MP600 Not really sure. (I am not a huge fan of Gerber). I was issued it while I was in Okinawa back in 1996. It kind of didn't get turn back in :) when I came back to the states. .It is really well made, but weighs on the heavy side for me to EDC.
-
So the Skeletool broke and fell apart on you :ahhh That is awful :-\ You need to get the pieces together and send it back to LM and tell them what happened
There warranty is superb 
-
I think that is a MP but I always forget what is what with Gerbers
Cool that it is one that was issued and even cooler it was issued to you 8) 
-
20180701_090138 by Poncho 65, on Flickr -
I decided to give the Skeletool another try. I sold my CX to Nate a while back but lately I've been thinking about picking up another one. Well, I won a nice used CX on the Bay tonight and it will be on it's way soon

-
What did you not like about it last time?
Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login