108mm Knifes Owner's Club!!!
-
Thks Barry. Here is eye candy for you : two recently acquired knives. The Safari is very hard to come by these days and fetches around $50. The Hunter is still available from a reputable tobacco supplier in Britain. But it was much more fun to source a gently used one at a good price.


-
Got a Safari for €20 last month :D
Where can I find that new Hunter??
-
@Mechanickal said:
Got a Safari for €20 last month :DWhere can I find that new Hunter??
-
Thanks!
Seems reasonable...
-
!! -
@Mechanickal said:
Got a Safari for €20 last month :DWhere can I find that new Hunter??
1/ Some guys get all the breaks. You lucky devil you. It's not fair, you already got so many..... leave a few for the small guys (like me)
2/ Where to ? You already got your answer. Bond's of...... they are also present on the Bay.
-
The new kid on the block raises two issues in the same post.
1/ do you consider the Swiss Shark as legitimate ?
2/ a few 108's were issued by Victorinox with a clip point blade. Who has one ? Can you show us pictures ? The picture below is borrowed from Sosak member Cliosguy without his permission.

-
I've got a Mauser, which has a spear point AND clip point blade.
I got that one mint for €35


-
@Ptisuisse said:
1/ do you consider the Swiss Shark as legitimate ?Who dares to question my legitimacy ??

-
I do too. It's a gorgeous knife that needs more attention from me, as does my well worn 108 GAK.
@Mechanickal said:
I've got a Mauser, which has a spear point AND clip point blade.I got that one mint for €35


-
@Barry Rowland said:
I do too. It's a gorgeous knife that needs more attention from me, as does my well worn 108 GAK.
@Mechanickal said:I've got a Mauser, which has a spear point AND clip point blade.
I got that one mint for €35



-
.

-
@Ptisuisse said:
2/ a few 108's were issued by Victorinox with a clip point blade. Who has one ? Can you show us pictures ? The picture below is borrowed from Sosak member Cliosguy without his permission.Mausers are nice, I own one I paid too much for considering its condition, but what interests me are the Solos that went out the factory with a non-etched Mauser blade, so to speak. Who has one ? who has a spare one (a "spear" one) ?
-
Left to right : Mauser, Trooper, Safari, Gak 1, Solo Plus, Solo.
-
Not shown : Safari Hunter.
[li]On the way in : Pathfinder.
- Worth mentioning on the grounds that they are assembled out of Victorinox-made parts : three Adler GAKS. Much rarer than the Vic ones.
[/li]

-
-
From what I heard those are the ones that came back from repairs at Vic.
Looks like they ran out of pen blades and started placing clip point blades instead.
-
I sent in a handful of 108mm gaks to Vic USA earlier in the year for blade replacement and they all came back with clip blades without any etching on them.

-
WOW
amazing news Simyo - it means two things :
1/ VIC is slowly running out of parts for this 40-year old series, it is quite likely they have no more spear point blades.
Here too in France, they are running out of red scales.2/ So, VIC US has actually accepted maintenance work on military issued knives ?
To me, it is not obvious these knives should be covered by their lifetime warranty.
May I ask if they charged you for service ?You have no idea how bad I would want one. What do you want for it ? (never ask this question to an american) (this is humor).
This news made my day :-)
-
Dear Simyo, can you confirm they re-fitted your original german army scales ? How solid is the fit ?
Here in France, scales are scarce, and some guys re-mold them out of poly-urethane resin.
This design below is a bit wild, (for sale on the Bay) but more sedate colours are also available.

-
They did charge I think it was about $12 us for the blade replacement and next day shipping back. Vic US is also running out of parts, the last one had the poorest repair since they had run out of springs and liners. They just reused the scales I sent. They fit alright, not as tight as original but still tighter than reusing celidor scales. At some point I want to build plus scales for mine, but that will have to wait until I get moved and my mini mill set up.

-
Simyo, thanks for this very interesting info. Liners, springs, even scales in good nick are not that hard to find, at least in Europe.
For metal parts you just break down an old GAK, and for scales, check out this guy on EPrey France :
https://www.ebay.fr/itm/Plaquettes-Victorinox-D-origine-Pour-Couteaux-Victorinox-108mm/232826718271?what the text says is easy to figure out : scales pried off new knives (the guy is an inveterate modder who can afford to open up a $50 new knife)
they have the cutouts marked for the "plus" versions. a llittle dab of epoxy glue in the holes and you're set. But they"re bloody Xpensive if you ask me.How about selling/trading a clip point bladed GAK ?
Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login
