Powerlock 30-day challenge
-
+1.

-
Day 07:
Did a little cut testing today:

The Powerlock's blade did a nice job with all these cuts. However, when I examined the edge afterward, I noted that the edge had rolled, quite significantly. Not good.
I re-cut the same materials with a Buck 110 with a 420HC blade and got similar results, but WITHOUT edge rolling.
This suggests to me that while the SOG's blade geometry is good, they haven't made the most of their blade materials and heat treatment.
sigh

-
The good side of soft steel is that it sharpens up easily.
This blade is ground thin and is very flexible. It's not a 'hard use' blade to be sure. Feels like I could snap it easily (with my gorilla-strength grip
).So, I suspect that's why the steel is soft and the edge rolls: a harder steel would be more prone to snapping. (And more returns to the warranty department.)
I'm going to keep an eye on the knife blade, here. Right now, I'm a bit underwhelmed, despite some decent cutting test results.
-
In my experience yes,
SOG's multitool blades have very soft steel :ahhh :P -
Day 08:
No uses today....so far. I will say that at this point in the challenge I have become quite used to having the Powerlock on my belt. It does not feel as big or heavy to me as a Leatherman ST300.
Maybe that just means I need to do a ST 300 challenge......


-
I've had similar experiences with SOG MT blade steel. It is about as soft as Vic blade steel. I don't mind though, because like you said, less likely to snap. And, like a SAK, it is crazy easy to sharpen. :)
LM and Gerber blades are not forgiving at all when flexed. I know this the hard way.
-
Day 09:

Explanation: I was transferring some lentils from a bag to a better storage system (recycled jar). I used the Powerlock's scissors to snip off the corner of the bag, so as to use the clipped corner as a funnel. Scissors (now peened) worked fairly well and cut through 98% of the bag before it folded over. Last 2% was torn off with the bag clamped in the scissors.
Not perfect, but OK-ish.
-
That’s a bit disappointing

Are the scissors sharp enough
-
In my view, nothing is ever sharp enough.

These seem decently sharp, but there is still a hint of wiggle in the scissors, even with my peening. Might be an indication to peen a bit more.

-
If you still have play than yes I would

-
The ST-300 is just a tad thicker than the powerlock. I've pocket carried both and don't notice much difference in how they carry. The scissors in my powerlock don't seem to have any issues. They're sharp and tight. I might have just gotten lucky and got the one that was assembled perfectly, right after the coffee break at the factory.
-
Day 10:
I'm off on a short overnight trip. Of course the Powerlock is coming along. I'll post up any pictures or stories when I get back. Until then, here's a morning glamor shot to tide me over:

-
Have a good and safe trip Nix

-
Day 11:
Back home now and no significant adventures. I was really happy to see there is still some snow lingering up on the peaks of the taller mountains. Snow is water, and water is life. So snow in July means water in the creeks and streams, and life in the rivers and lakes. And that puts a smile on my face.

I did struggle a bit with the scissors again. I'll try to peen them some more in the next day or two. Otherwise, the Powerlock just rode along for the journey. Awlways nice to have a multi close at hand.
Time for a G&T now, so......

-
Oh, here's another funny thing:
SOG sent me a second Powerlock with scissors. I'm not sure how that happened. Maybe when I returned my PowerAccess Deluxe it triggered an exchange that resulted in my being sent a second Powerlock (w/scissors).
As a result of this fiasco I'll be doing a GAW of a NIB Powerlock with Scissors at the end of this challenge. I'm going to keep this GAW quiet and just limit it to those MTO'ers who comment in this thread. So, if you've commented here already, you are in. If you would rather not have a NIB Powerlock, don't comment in this thread. If you want to give a Powerlock with scissors a try, make at least one post in this thread: anything from a popcorn smiley to a lengthy discourse on your love of SOG Powerlocks. No need to keep a list, I'll figure it out at the end of the challenge.
This has just been too funny.


-
Nice one Nix that’s funny

And how did the knife do with the cutting

-
Excellent job on the lime slice.
Hey, I resharpened it after the last cutting trials. ;)
-
If you break your current PL, you won't need to send it in for replacement.

Not sure how I feel about them sending two PLs out though. Only because it seems as if one hand doesn't know what the other is doing. That sort of thing ends up costing the consumers from what I've seen. One of the possible reasons SOG's MTs are more expensive than the U.S.A made LMs and Gerbers(in general regarding staple-models).
It worked out since the PAD was quite a bit more expensive than a PL though. Definitely got your money's worth.
Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login

