Need to understand "Rebar Love"
-
Day 9
Near the end of the first third of this - a little bit challenged - challenge, I present a shot of two Rebars for the price of one.

-
@Dutch_Tooler said:
Day 9Near the end of the first third of this - a little bit challenged - challenge, I present a shot of two Rebars for the price of one.
:ahhh the Chess Rebar team :D

-
Rebar Chess
you'd need 32 LMs - Micras as pawns etc. :DDay 10
After a recent, not too emboldening experience with the sheath that comes with the SOG Power Access Deluxe, it is now time to extol the largely unsung virtues of the sheath that came with the (BO part of the) Rebar VX, although I bought this one used, so no idea if it is stock.
The LM sheath features a velcro fastener worthy of the name, Molle attachment and an internal separate nylon pocket into which one can wriggle an entire bit set (nice for the bit driver I incorporated in the Rebar VX), while still leaving enough space for the Rebar. I still need to experiment with storing a bit driver extender though.
Less bulk could be achieved by storing the bit set in a separate pouch, of course, at the cost of space as measured along the belt ;)




-
Nice ones DT
I have the molle sheath with the bigger grommet and I have been using it for close to a year now and except for adding a snap it is holding up very well

-
Nice set up there D_T. I really like your VX mods, they seem to step up the Rebar to a new level.
-
Thanks gentlemen

Yup, I'm pretty happy with how the VX has turned out. I might need to trim down the thickness of one tool in one handle a little - the hold of the pivot in its holes in that handle is a little bit marginal, although in practice this doesn't show yet. Otherwise, it packs a lot of punch for its size.
Day 11
None of the above would have been possible without a good basis in the original Rebar. Arguably this is the current LM offering that comes closest to the original PST, in construction, size and intent. I invite all to take a look below, where I show off the VX's counterpart in colour, that has the original tool loadout (albeit in BO here). LM even managed to recreate the feel of the PST's original sheath, although they did change the material from real leather to synthetic (pity, that). The sheath looks and feels solid enough, but the tool rattles slightly, and of course the sheath's form factor and choice of material makes it bulkier than strictly necessary for the Rebar.

-
Yes I do prefer the old school leather sheaths
Excellent pics today of the SS on BO

-
Or is this BO on SS
??? :ahhh:D
-
Dunno, I get confused myself at times :ahhh :ahhh :ahhh but thanks

-
@Dutch_Tooler said:
Yup, I'm pretty happy with how the VX has turned out. I might need to trim down the thickness of one tool in one handle a little - the hold of the pivot in its holes in that handle is a little bit marginal, although in practice this doesn't show yet. Otherwise, it packs a lot of punch for its size.Is it the handle with the bit holder, and if so what have you thought about trimming down. How about some close ups of the issue while you're at it.
@Poncho65 said:
Or is this BO on SS
??? :ahhh:D
I don't know either but I
it.

-
Thanks! Well, it's not actually an issue in practice. Also, I can't show you without taking the thing apart, if even then (the pivot is just a little bit too short to accommodate all the tools and still fully extend into the holes in the handle in locking engagement with the latter - the engagement is only partial). It's in the handle opposite the large bit holder - see pic. I have thought of thinning the awl and/or the large screwdriver. Probably only the awl, by a tenth mm or so - that shouldn't impair its function.


-
Day 12
Comparing sizes today. Size does matter, after all, if not always in the way you think when reading this first line :D
Pitting the Rebar against the ST300 is somewhat akin to comparing a mouse and an elephant. However, for all its relatively diminutive size, the Rebar already in its original version comprises all essential tools in a relatively compact, pocketable package. (I have been known to pocket a Rebar. This is not possible with an ST300, unless you wear cargo pants/shorts or dungarees, which I avoid at the office).

@Poncho65 said:
Nice ones DT
I have the molle sheath with the bigger grommet and I have been using it for close to a year now and except for adding a snap it is holding up very well

Thanks Ponch -I take it you mean the 2nd sheath in the pic?

The last pic shows how the sheathed ST300 is comparable in bulk to the sheathed Rebar WITH bit set. Goes to show how compact a Rebar is.

-
@Dutch_Tooler said:
Thanks! Well, it's not actually an issue in practice. Also, I can't show you without taking the thing apart, if even then (the pivot is just a little bit too short to accommodate all the tools and still fully extend into the holes in the handle in locking engagement with the latter - the engagement is only partial). It's in the handle opposite the large bit holder - see pic. I have thought of thinning the awl and/or the large screwdriver. Probably only the awl, by a tenth mm or so - that shouldn't impair its function.l had this issue as well and it was bugging me. l solved it by replacing the pivot with a longer one from a Fuse - it's about 1 mm longer and allowed me to use the anti clump washers between all the tools.
-
Thanks george1, that is a tip I might be following up

-
Thanks for the photos D_T it helps to see how the mod works and a great size comparison. george1 sounds like the perfect solution to D_T's issue.
-
Great pics DT the close ups are great
and yes like the 2nd sheath in the pic
I have been known to pocket a Supertool :o :D -
D_T you're going to have company again thanks to Gerleatherberman.

Another package arrived at my place today, ??? unfortunately delivered by the Postman not Chuck Norris (what a great guy).

I managed to snag my Mora back from Danni
and opened it up only to find a heavy bundle of ... 

After getting through all that I found myself face to face with a Rebar
and G-man's sense of humor.



and best of all

.Showed all this to Danni and she responed with now you'll have to get a chain for the chain.

Now that's a real

-
THANKS
GERLEATHERBERMAN -
Wow very cool Doug
Very nice of GLBM as well and a
to him 
-

Douglas,
I'd shake your hand, but my arm isn't long enough to reach Texas. Your friendship is very much appreciated.

I may have gotten carried away with the engraving tool.....and chain.

But, nobody will have to ask, "is it yours, Douglas?" :)Danni,
Your response was perfect! Thank you. Now to find Douglas a chain for his chain.
Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login