The Wingman has been shot down!
-
I, uh, need a sacrificial Wave too... :D
No problem, just move to the North Atlantic, get an outdoor job on the docks, and it will be in the mail

:D
I live in the north, does that count for anything??
-
Actually, I only have one Wave, and it's an original. It also belonged to my good friend Dave Bowen, and I promised I would keep it in good shape for him as it does have some personal significance to him.
I'll keep the CRKT Tool going for a bit longer as I do like to get some significant use out of them before writing a review, but when I've done that I'll give a Wave a shot.
Def
-
I am suprised about the Leatherman...I will say this and I wish I had taken Pics..It took quite a bite to get some rust on my SwissTool..I literally used it hard and put it away wet while re wiring a Plug on the side of the road when my trailer lights went out in a rainstorm..then a few weeks in my Jack Pack..and even then the grease and crud that normally accomapnies Semi Trailers was more of an issue than the Rust..Maybe Leatherman is using cheaper materials or finish on the Wingman..Never had a prolem with my Wave or Supertools..
Dtrain
-
A couple months after I got my Wave, it developed rust. It wasn't alot, but it was little specks of rust spread out over the entire tool. It was the height of summer and hot and pretty humid, plus I have sweaty hands. The tool was getting a fair amount of use, too. Anyways, I took the green scratch pad to it with some soap and water, then coated it in WD40. No rust since then, that has been a year ago, now.
I think Leatherman just uses a metal it feels allows them to keep their tools more affordable than a Swisstool or SOG. The WM/SK metal seems to be lower quality than the other Leatherman's I have experience with, but the tools are even less expensive.
I have had a Skeletool for a few months now, and it has not developed any rust at all so far. I have had a Wingman since January that has not developed any rust at all so far.
-
Since I just linked to this thread in another thread I figured it might as well be today's Official Dirty Dozen Thread Necro. It's a good thread for everyone to be aware of whenever we get into the Rusty Leatherman discussion.

Def
-
So did you ever get to carry a wave and test it out ?
-
I never did get a newer Wave. I still only have the original, and I'm not going to ruin that one. It is valuable to a good friend, and therefore valuable to me. :D
I also haven't done that job in a couple of years, since I left it after getting hurt.
Def
-
Don't know if it is still relevant, but what I always do when I come home on a friday after a whole week of putting my leatherman to heavy use, both indoor and outdoors, is to give it an over night bath in WD40....sometimes I even leave it all weekend soaking in WD40, then the night before I go back to work, I get it out of the WD40 bath and wipe it down and oil it back up with 3-in-1 oil.
Been doing this for the last 3 years, never had a problem with rust, even after it has been with me out on the ocean fishing or hiking / camping all weekend as well.
That works for me at least.
-
*What MMR said!
I skip a step and have converted to the new 3-1 drying silicone oil. I use a paint brush to wipe the tool down in a thick coat and leave it out on the table over night. The oil dries to a non-slime film that prohibits rust. I have had a pinchy in my back pocket for months without rust, because of the silicone oil treatment. I had a Wingman in my pocket for six months last year (through 98f temps and 100% humidity) and had no rust. My Spirit had rust forming on the pliers and sharpened edges as well. One silicone oil treatment and it stopped. I do this to all of my MTs. The oil dries and doesn't attract dirt/dust like non-drying oils do.
-
I have a very rusty juice I put into use and it lasted a it a month. Rusted so bad now it won't open. Yes I will take pics.
-
Seems a bit silly for a tool to require nightly application of an oil coating. :P
And I hate fondling oily metal! :ahhh -
@Don Pablo said:
Seems a bit silly for a tool to require nightly application of an oil coating. :P
And I hate fondling oily metal! :ahhhI do the silicone DRYING oil treatment once every 6-8 weeks, depending on the weather. No oily metal and no rust.

Gotcha.

-
I live in a pretty dry environment now, at least in the summer, but in winter it's snowy and rainy. I hardly EVER clean my Rebar. Even after dropping it in the snow while working on my snowblower, I just dried it off with a paper towel and put it back in it's leather sheath. I think I might have cleaned it once or twice in the last 2 years.
-
Given I live in Scotland (obviously known for it's aridly dry atmosphere ::)) I'm pleasantly surprised by the fact I've never had a rusting issue with any of my LMs. Nor do I take any preventative measures other than wiping them dry when they get wet.
Mind you, I don't normally spend any time near salt water either. -
For the record, I still have the Wingman and I have never cleaned it up nor have I ever used it for anything ever since. It is safely tucker away in a drawer along with some other great multitool failures, like my "new" Pulse.

Def
-
Grant, sounds like a LM you could spruce up and do a GAW with. :)
And I feel your pain on the Pulse. I paid $65 for one in "near mint" condition. I spent 6hrs making it "acceptable". Buyer gave a smallish partial refund, but wow.

Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login