Supertool 300 VX upgrade (Mod badge request too)
-
So here is a pic with new CF scales, epoxied on. Found out I only need glue on the central ridge of the scales - in fact not on the side ridges as then the little bit of give necessary to provide spring action to hold the T&T would be inhibited completely. But the upward splay is considerably reduced. I can live with this setup. The outside has added roughness as well.

Sent on my SM-G930F with Tapatalk
-
Cool 8) Hope that the epoxy holds
I have held many things together with epoxy and have faith in it so you should be good 
-
Thanks. My experience too tells me it should work out just fine...
Now, to apply something roughly similar to Rebar VX...

Sent on my SM-G930F with Tapatalk
-
@Dutch_Tooler said:
Thanks. My experience too tells me it should work out just fine...Now, to apply something roughly similar to Rebar VX...

Sent on my SM-G930F with Tapatalk
:o

-
Nice !

-
@Dutch_Tooler said:
Thanks. My experience too tells me it should work out just fine...Now, to apply something roughly similar to Rebar VX...

Sent on my SM-G930F with Tapatalk
Having trouble getting my head around this task. Rebar handles have much less space, the spring slots are skewed and there's a rivet in the way. Also, the VX now has BO handles; I have some qualms about epoxying anything onto them. And although the rulers have limited use at best, I'd still like these accessible so those surfaces are out of the question for any around-the-handle-edges clipping solution

Sent on my SM-G930F with Tapatalk
-
Back to the ST300VX scales.
I was planning to also carry a Firefly ferro rod in one of them. Unfortunately, the tool slots are too narrow, seems the Fireflies are wider than the T&T by quite a margin, and I used the T&T as templates for the design of the scales. Will have to redesign them (again sigh)...
-
@Dutch_Tooler said:
Back to the ST300VX scales.I was planning to also carry a Firefly ferro rod in one of them. Unfortunately, the tool slots are too narrow, seems the Fireflies are wider than the T&T by quite a margin, and I used the T&T as templates for the design of the scales. Will have to redesign them (again sigh)...

-
gonna Add firefly and pen to ULTRATOOL THANKS DT


-
Good idea Obi, just take care when trying to fit the Firefly as it is quite a bit wider than tweezers or toothpick.
As to the pen, I think the long model may be too long. I've thought about using the short MiniChamp model, maybe with some kind of holder/extractor stub added...
But those are for dark winter nights.
-
Rainy day today... a modifed handle scale has just rolled out of the 3D printer. This is intended to hold a Minichamp pen and Firefly ferro rod. It's a prototype, but looks OK after some filing, and the epoxy is setting

-
Very interesting

-
I can't see any pics...

-
So this is the rough idea, shown with a placeholder ballpoint pen. Tolerances are too tight though and I'll have to redesign the scale with a tad more generous tolerances

The second pic shows the Minichamp type ballpoint pen that is going to be used, mounted in D-T's advanced lo-rev rotary epoxy setting gravity action compensator during the first few hours of setting of the blob you can see at its end. This blob will be cut and filed down to a small handle nub.


-
Nice first attempt D_T can’t
wait to see the finished product

-
Take 2:
-
Great first attempt DT
can't to see the next design and model 
Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login