September Storm: 30 days of Waves
-
The Wave is lookin’ good, peeps!

Glad I got my image hosting working well

-
Unfortunately Zed won’t be able to do the
challenge with us as he is very busy at the moment
Good luck Zed
Nix
Wspeed
gerleatherberman
Antti Lammi
LoopCutter
Poncho65
Pacu
Jaypeebee
Sam
LanWolf
Obi1shinobee
Sean24
CallsignBadger
Douglas
SteveC (I'll give you a definitely for sure maybe)
MTMatt
aolmos
eamo
Dutch_Tooler
italophil
Glockfan
ReamerPunch
Thegreatdane -
Awww..... that's too bad.
@ Zed, we'll save a spot for you, in case you can make it. Even if you can't do the full challenge, pop your head in and share a thought or two.

-
I had some time today so I decided to put a S30V blade into the Wave+. I also switch the positions of the SE and serrated blades, so my thumb rests on the SE blade when I pull it out of the pocket using the clip.
The obvious choice would have been a vise and two bit holders, but where is the fun in that. Instead the two predecessors and LM support gear stepped in and excelled at their task!
Please excuse the pic quality; my basement doesn't have the best lighting for taking photos.
-
Nice job italophil

-

Using MT’s is awlways more fun

-
-
@italophil said:
I had some time today so I decided to put a S30V blade into the Wave+. I also switch the positions of the SE and serrated blades, so my thumb rests on the SE blade when I pull it out of the pocket using the clip.The obvious choice would have been a vise and two bit holders, but where is the fun in that. Instead the two predecessors and LM support gear stepped in and excelled at their task!
Please excuse the pic quality; my basement doesn't have the best lighting for taking photos.
Does those blades lock correctly, if im not wrong blades have desing that they goes only right way or did you grinded bit those bottoms
Only Tools Matters
-
@italophil said:
I had some time today so I decided to put a S30V blade into the Wave+. I also switch the positions of the SE and serrated blades, so my thumb rests on the SE blade when I pull it out of the pocket using the clip.The obvious choice would have been a vise and two bit holders, but where is the fun in that. Instead the two predecessors and LM support gear stepped in and excelled at their task!
Please excuse the pic quality; my basement doesn't have the best lighting for taking photos.
Nice job! You'll have it just right when we start the challenge.

-
@Antti Lammi said:
Does those blades lock correctly, if im not wrong blades have desing that they goes only right way or did you grinded bit those bottomsOnly Tools Matters
Yes, the blades lock up is great. They lock in the open position for the knife and lock closed in the plier position. The two knife blades are interchangeable with each other, as are the saw and file; but you can't switch a blade with either of the other tools, neither the lock-up in the plier position nor the cut out for the OHO match.
-
Forecast is for high surf. I'm stoked!
-
+1

-
It's so close! :ahhh
-
has anyone tried cutting network cables with the Wave+ and compared it to Wave, Spirit and Rebar (since those are the usual competitors)?
-
ReWaveR reports stashed in checked luggage for Transatlantic trip to be at hand when the challenge starts

styx, not tried that yet but let's see if I can sneak a piece of Cat 5e into my bag...
-
Did a quick comparison between wire cutters vs. Cat 5e network cable.
First cut with an old Charge, should be similar to non-plus Wave. Pretty good result - clean cut but the length of the cutting surface is just too short to manage without one repositioning and a second small cut.
Second cut with Rebar: cut was even cleaner and required less force, cutter a tiny bit shorter than the Wave's so repositioning and recut necessary. 1 strand missed.
Third cut with Spirit. Very short cutter, had to reposition twice for three cuts in all, but reasonably clean cut.
Fourth cut with SOG PAD. Cutters should be long enough (longer than Wave's) and almost no force needed (compound leverage rocks) but the gap between them makes for an unclean cut that leaves multiple strands of the outer insulation uncut.
If and when a Wave Plus joins my stable, I'll test it too.




-
@styx said:
has anyone tried cutting network cables with the Wave+ and compared it to Wave, Spirit and Rebar (since those are the usual competitors)?Hmm. I think this comparison will be very subjective and have no which cuts better kind of answers. The most one can compare will probably be how long individual cutters are. There no 2 tools alike. Even the same model.. Different level of wear gives different results. If my wave cuts them cleanly, it doesn't mean other people's wave will...
Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login