Sog Powerlock 30 day challenge
-
@gerleatherberman said:
Indeed. Thank you!I apologize for getting so off-topic, RF!
Any mischief planned for the PowerLock today?
No problem, that's the Mto way [emoji16]
Not much mischief today.Sent fra min FRD-L09 via Tapatalk
-
Day 11:
Used the scissors to cut a finger of a rubber glove to keep my finger away from to much dirt and oil as I slipped with a knife while camping and cut of a piece.
It's not to bad but the fingers bleed like a smurf.


Sent fra min FRD-L09 via Tapatalk
-
Glad it wasn't any worse of a cut! I accidentally cut myself all the time at work, so I'm familiar with the glove piece and tape. :ahhh
Those scissors can cut a glove like that, then they are pretty good. IMO.
I find latex/vinyl/nitrile gloves tend to bind up in small scissors, even some SAK scissors. -
I think they work very well, can't figure out what the fuzz was about them beeing crap in other threads, maybe I was just lucky [emoji106]
Sent fra min FRD-L09 via Tapatalk
-
Good stuff, RF!
Very glad to hear your scissors are performing for you.

Sorry about the finger slice. :-\
-
Thanks Nix [emoji16]
Sent fra min FRD-L09 via Tapatalk
-
Day 11 bonus pic:
Had to sharpen it quick as a small part of the edge had rolled again, no idea why this time [emoji848]

Sent fra min FRD-L09 via Tapatalk
-
Must be soft metal maybe not hardened properly

-
The blade on my newer PL rolls easily as well. I think SOG tapered the blade a bit too much to the edge. Makes it a fair slicer, but their steel isn't heat treated like LM and Gerber. SOG and Vic blades tend to dent or roll more easily from my experience. But, on the plus side, they touch up fairly easily. :)
The blades on my older(U.S made) PL seem a bit harder and take a lot more to roll the edges. Probably a better heat treat, combined with a thicker blade.

-
A great challenge day, RF52


-
It's not much of a problem as it is quick and easy to sharpen up again, just a little annoying when it happens.
Thanks CallSignBadger [emoji16]
Sent fra min FRD-L09 via Tapatalk
-
Especially if you want to cut something
and have to sharpen the blade first
Not what you need in a rush situation ??? -
That can be really frustrating [emoji20] The serrated part of the blade is still going strong though [emoji106] I wonder if the plane edge comes in contact with the inside of the handles because it's possible to move it up and down when closed [emoji848]
Sent fra min FRD-L09 via Tapatalk
-
Interesting I wonder

-
^ +1
That seems to happen to a lot of blades...
-
RF52,
Maybe check the blade tang and see if it has enough "rise" to prevent the blade edge from hitting the inside of the handle? I haven't noted this on a PL, but I only have two newer ones, so not a big enough selection to know if this is a problem or not.

I have a BuckTool that has a tang without enough "rise" and the lock button hits the blade edge. :ahhh
So, just throwing ideas around. Hopefully that isn't the case, because the fixes are frustrating (re-edge the PE portion passed the point of contact, replace blade, send in for repair). -
@gerleatherberman said:
RF52,Maybe check the blade tang and see if it has enough "rise" to prevent the blade edge from hitting the inside of the handle? I haven't noted this on a PL, but I only have two newer ones, so not a big enough selection to know if this is a problem or not.

I have a BuckTool that has a tang without enough "rise" and the lock button hits the blade edge. :ahhh
So, just throwing ideas around. Hopefully that isn't the case, because the fixes are frustrating (re-edge the PE portion passed the point of contact, replace blade, send in for repair).It does hit the inside of the handle, I can see a small mark that is shinier than the rest of the handle and I believe it's the lock notch in the closed position that is the problem since I can move it up and down quite a bit when it's closed.
It doesn't really bother me that much as I'm concidering a mod after the challenge, just have to decide on what components I want [emoji106] It's good to have a look at it once and a while to keep it sharp though.Sent fra min FRD-L09 via Tapatalk
-
That’s a shame that it hits the lock notch
Just thinking if you could grind
the notch down a bit so that it won’t hit

Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login

