Seeking Rebar modding advice.
-
@Don Pablo said:
You guys seem rather enthusiastic about Loki’s wrenches. :D
I was until mine stripped out completely. Engineer pliers for me.
Which one stripped out, if it was an early 4 way one and the PST size loki will likely send you a replacement. I have one and I guess the PST size was slightly oversized which would cause it to slip. loki sent me a replacement.
It was the first set.
-
My adapter for Rebar, i recommend that you go for 3d adapter cause it gives more compatibility. Dont mind blade if its not really necessary for you or you carry something else what has blade.


Only Tools Matters
-
I wish Ireland was like the UK at least.... because in the UK, you can legally carry under 3” non-locking knives like SAKs without needing a reason. :D
Of course, it’s still a bad idea to take your SAK to the pub. ;) so there are limits. -
@Antti Lammi said:
My adapter for Rebar, i recommend that you go for 3d adapter cause it gives more compatibility. Dont mind blade if its not really necessary for you or you carry something else what has blade.

Only Tools Matters
Yeah, I agree.
The 3D bit adaptor is the more feasible / reasonable option
And no, I don't need it to have a knife in it. The times I need a Knife, Serrated Blade or a Saw in it, I have a Stanley utility knife that I use, when I need a knife, which does the job perfectly for me.
I work in the wine business, so all I really need a knife for is to open boxes. :)
@Don Pablo said:
I wish Ireland was like the UK at least.... because in the UK, you can legally carry under 3” non-locking knives like SAKs without needing a reason. :D
Of course, it’s still a bad idea to take your SAK to the pub. ;) so there are limits.Agree 100%
But lets be honest; it's pretty much a daily occasion in cities like Dublin and Limerick, that someone gets jumped or attacked, so I would say that there is a good reason for the law being written the way that it is here in Ireland.
-
@Don Pablo said:
I wish Ireland was like the UK at least.... because in the UK, you can legally carry under 3” non-locking knives like SAKs without needing a reason. :D
Of course, it’s still a bad idea to take your SAK to the pub. ;) so there are limits.Agree 100%
But lets be honest; it's pretty much a daily occasion in cities like Dublin and Limerick, that someone gets jumped or attacked, so I would say that there is a good reason for the law being written the way that it is here in Ireland.
I tend to think that London and etc have the same problem.

-
@Don Pablo said:
@Don Pablo said:
I wish Ireland was like the UK at least.... because in the UK, you can legally carry under 3” non-locking knives like SAKs without needing a reason. :D
Of course, it’s still a bad idea to take your SAK to the pub. ;) so there are limits.Agree 100%
But lets be honest; it's pretty much a daily occasion in cities like Dublin and Limerick, that someone gets jumped or attacked, so I would say that there is a good reason for the law being written the way that it is here in Ireland.
I tend to think that London and etc have the same problem.

True
Sent from my iPhone using Tapatalk
-
Update:
After looking at the bit driver adaptor thingy in person, I wasn't feeling it at all, for me it was first of all too expensive for just a tiny bit which I have a gut feeling I will lose too easily, and ever since I started looking at getting my Rebar, I have been wanting to make it more personal to me, i.e also why I removed the knives and saw the way I did, because I was going to remove them anyway, and it was cheaper to buy the regular rebar than the knifmeless model......
....yeah, okay...blah..blah..blah..blah..yadda...yadda..yadda....long story short; I decided to go the "loki route", and ordered the 2D large bit driver and small bit driver parts and a set of Lokis wrenches too.
Plus I already have a homemade 2D to 3D bit adaptor which I have been using with my Charge.
I'll update the thread once I receive the parts and wrenches from Loki....and then it's modding time! ...so have the popcorn ready! ;)
-
While I am waiting for my parts and wrenches to arrive from Loki.
I keep looking at Annti’s review / comparison of the ST300 and Rebar, which got me thinking a bit.
Do you guys think the Phillips driver from the ST300, will fit in a Rebar? ...or is it too long(insert “that’s what she said” joke)?
Sent from my iPhone using Tapatalk
-
It would require a lot of modding around the pivot area. ST300 tools are compatible with Surge.
What's wrong with the Rebar's own phillips? -
@Syncop8r said:
It would require a lot of modding around the pivot area. ST300 tools are compatible with Surge.
What's wrong with the Rebar's own phillips?Ah I see...
...oh nothing wrong with it, it’s actually one of the tools I use most. For the same reason, I wanted to see if it is “upgraderable”, so to speak, with a bit of extra reach.
Sent from my iPhone using Tapatalk
-
Alright laddies!
After a long wait the stuff from Loki finally arrived, and here’s what I mcgyvered together!

So I wanted to keep all the full sized screwdrivers bit still have the small and large bit driver.
And here’s why..

I already have this homemade redneck fabulous 3D bit driver that I made ages ago for my Charge TTI, so I wanted to be able to use both 2D and 3D bits.


And that is especially when Torx and Hex are becoming more and more common, especially on European cars and different electronics

And it all fits nicely into my charges sheath as well!
And most importantly; no knives means it is legal to carry in public!
Sent from my iPhone using Tapatalk
-
Even works with my small sockets...

There’s these long bits too...

And I can even go down this route as well if needs be...

I hope it this forms a better picture of what I had envisioned and what I was hoping to achieve with this “build” / mod
Sent from my iPhone using Tapatalk
-
Looks good MMR

-
Thank you sir!

Sent from my iPhone using Tapatalk
-
Awesome homemade bit adaptor MMR, how did you make it?

-
@Don Pablo said:
Awesome homemade bit adaptor MMR, how did you make it?
Woodies sells these “onsite” brand bit sets for €5, which comes with a regular bit adaptor for like a power drill.
I took that, and measured up the size of the leatherman 2D bits, and grinder it down on both sides to my measurements
I don’t know if that makes sense?
Sent from my iPhone using Tapatalk
-
Oh yes MMR, it makes purrfect sense :D
I'll have to try that out. I may need to go for a somewhat higher powered grinding wheel... >:D -
Just for inspiration; it looks like this up close

One thing to note, if you decide to have a go yourself; the 2D bit driver has this little locking arm; which it uses to secure the bits in place:

So cutouts like I did here are needed for the bit adaptor to lock in place, as seen below:

Here’s a better picture of the cutouts:

Sent from my iPhone using Tapatalk
Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login

