September Storm: 30 days of Waves
-
Nice one Obi

-
Nice obi!
Antti, Nice wave knife !
Day 4,
as i went to Germany today, the wave had to stay home, acompanied by a few brothers and sisters. (What lm is male, what is female?)
But back way before minight, and the wave could assist in opening the mail !
(Received leds for a botle)

-
-
Excellent uses and pics everyone

-
Antti, Nice wave knife !
Day 4,
as i went to Germany today, the wave had to stay home, acompanied by a few brothers and sisters. (What lm is male, what is female?)
But back way before minight, and the wave could assist in opening the mail !
(Received leds for a botle)

Nice lamp LanWolf

Yes, Waves are not legal carry in Germany, although I think exceptions are usually made for hiking and climbing. You can buy them legally at any rate.
-
DAY 4

I thought you liked
:DThat hooked SE blade, was that once BO?
I got 3 Serrated gut hook from TTC junks hahahaha got alot parts from them . 
-
That's a great catch you made there Obi

Meanwhile, continuing **Day 4 **exploits.
A non-standard awl on ReWaveR at work fashioning one of two holes between two tiles for a toilet roll holder, followed by further pre-drilling using the screw and the ReWaveR's fixed Phillips, later used to finish the screwing on of the brackets for the holder halves. The latter task could have been carried out using a Wave bit holder and Phillips bit, of course. But I'm happy I included the awl :D
The awl is based on the Rebar small fixed screwdriver. Quite a bit of material had to be ground off and the hole was difficult to make.


-
Day 4 of 30
Looks like I was holding the edge of the blade with my finger now that I look at the pic :ahhh. But I wasn't and didn't get cut
Opened a water bill with the SE :'( and the Wave cut through the paper like hot butter

2018-09-04_05-05-54 by Poncho 65, on Flickr -
:o

-
Lots of
for all todays posts, good stuff.
DAY 4
Used the scissors to trim lables, the bit holder and extension on contactor lugs and OH NO
The Wave could not get to the lug on the terminal block, had to break out the Spirit.



-
An OG Wave could have handled that task :D
-
The down side to dropping seperate drivers in favor of a bit holder on the G2 version. Some times progress almost seems backwards. 
-
** Day 4 **
Just got home, and opened some bread with the Wave

I’ll let you guys know if anything else happens :P
The weekends will most definitely have more Wave usage, so another reason to be excited about Friday!
And great uses, peeps

Might have to build my own ReWaveR for the dedicated drivers, who knows ;)
-
Day 4 - At my part time job, we shut down the indoors pool for annual maintenance, New parts arriving and a lot card board to cut down for recycling. The SE blade works great for this task.
Also, earlier discussion concerning sheaths, and question concerning nylon was asked. Via another member I was pointed toward the Ozark brand formed nylon sheath included with a $3.97 MT sold at WalMart.
I bought 3 of these units just for the sheath. I am still on my first sheath, I use for both my WAVE and REBAR when worked full time in specialty construction, and now retired it has been returned to service in my PT job doing maintenance at a large YMCA near my home.
I did not want to damage my leather sheaths while working on the concrete pavement, or other rough services so turned to nylon. Mole sheaths fell apart. So this is my daily use sheath, and leather goes out on weekends when less hazardous conditions present themselves.
I also included a picture of my EDC sheath with a new one to compare the strap wear.



-
Day Four
Slow Wave Day Today.
Today I am guilty of being lazy after a long weekend wiring an entire house with electrical.
I decided to oil up the Waves a bit with Uncle Def's Premium Tool Oil.
The Wave + is still tight after a couple weeks of use. Still no quality issues found with Leatherman's lastest Wave production model. 
The original Wave seems a bit small compared to the Wave +. Knife is thinner on the original Wave.
-
DAY 4
Due to having a full tool bag at work, didn’t need the wave today.

Sent from my iPhone using Tapatalk
-
Find a couple of LM bits for the MUT. They're even longer than the regular driver shanks.

https://www.leatherman.com/mut-bit-kit-140.html -
Day 5
Back at work. Attempt to repair my old battery drill.. Long shank came in handy for those recessed screw. Repair didn't work out though.. Ended up throwing it away.....


Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login

