Evolution of Wood Saws on 91mm Victorinox SAKs
-
You are right, they didn't go from 27 to 29 teeth in early 1950s just changed nail nick type from large one usual in last 1940s to small nick. Looks like they produced 39 teeth saw till 1957. Here is my Champion with 39 teeth saw, post 1957 hidden rivets but old (pre1957?) square LNF nick and rounded bail.


What are the blade stamps on your knife with 29 teeth saw with nail nick?

-
@jnoxyd said:
You are right, they didn't go from 27 to 29 teeth in early 1950s just changed nail nick type from large one usual in last 1940s to small nick. Looks like they produced 39 teeth saw till 1957. Here is my Champion with 39 teeth saw, post 1957 hidden rivets but old (pre1957?) square LNF nick and rounded bail.Many thanks for these images, Jnoxyd!
I have never seen before now a saw with 39 teeth on a Victorinox SAK with hidden rivets, so this is very interesting for me. Since I did see saws with 29 teeth on SAKs with visible rivets, like the one in the first attached image below, it looks like the transition from 39 teeth to 29 teeth indeed happened around the same time of the transition to hidden rivets (presumably 1957).What is also very interesting for me is the fact that your saw with 39 teeth is right-weighted (type SW39ARSP). Before now I had no way of telling if the right-weighted saws with 39 teeth came before or after the left-weighted ones. Your SAK suggests very strongly that the first saws with 39 teeth were left-weighted and that they got changed later on (possibly around 1955, say) to right-weighted saws with 39 teeth.
Regarding the changes in the late 1940's/early 1950's: Some of the wood saws on SAKs from the 1946-51 period, like the one in the second attached image below, have standard nail nicks. I thus tend to believe that the change from extra-long nail nicks to standard nail nicks (namely, the change from type SN27ARLP saws to type SN27ARSP saws; the only difference between these two types is in the nail nicks) occurred at some point towards the end of the 1946-51 period (possibly 1950, say). This change is not the big change that occurred a little later in the early 1950's. What happened with the big changes of the early 1950's (along with the change of distances between the rivets, change to aluminum liners, introduction of several new tools, etc.) is first and foremost a significant change to the shape of the saws from what I called above narrow-form saws to wide-form saws. The narrow-form saws of the 1940's have shanks that are about 10mm wide and 1.75mm thick, whereas the shanks of the wide-form saws are about 11.5mm wide and 1.65mm thick (like the ones on current SAKs). It looks like along side this change from narrow-form to wide-form (namely, from type SN27ARSP saws to type SW27ALSP saws) the teeth weighting also changed from right to left, but I believe that the type of the nail nick changed a little before then.
Do you happen to know when they started with the extra-long nail nicks?
What are the blade stamps on your knife with 29 teeth saw with nail nick?
The blade stamps on the model 236fmaU from the image above are identical to the blade stamps on the model 236aU in the first attached image below: VICTORIA-OFFICIER-SUISSE (which can be seen in the image) on the back along with the usual VICTORINOX-SWITZERLAND-STAINLESS-ROSTFREI on the front. However, the same saw variant can also be found on SAKs with the VICTORIA-OFFICIER stamp on the back of the blade, such as the one in this post by GigaHz.


-
My Benrus and other 1940s knives have long nail nick [emoji6]

Earlier knives from my friend Rene (aka Der Eidgenosse YouTube ) have small nail nick. So we need more knife pictures from that period to tracing the changes [emoji6]. Maybe MTO members can show knives they have.

BTW 236 aU you shown above has visible rivets and VOS CB/ VSSR stamp that was introduced c.1957 (IMHO) instead of previous VO CB/VSS (1952-1957) so your knife is c.1957. -
@jnoxyd said:
My Benrus and other 1940s knives have long nail nick [emoji6]
Earlier knives from my friend Rene (aka Der Eidgenosse YouTube ) have small nail nick.Thanks a lot for these images, Jnoxyd!
I'm learning interesting things from them.
I'm particularly intrigued by the middle SAK on the second image. The saw on this SAK is right-weighted and looks very similar to the saw on my above Benrus SAK. This makes me think that it may be from around the same time, but the color of the scale seems a bit wrong for a cellidor SAK. Do you have more images and/or other information about this SAK?So we need more knife pictures from that period to tracing the changes [emoji6]. Maybe MTO members can show knives they have.
Yes. It would indeed be great if more MTO members will post relevant images. Please please please...

BTW 236 aU you shown above has visible rivets and VOS CB/ VSSR stamp that was introduced c.1957 (IMHO) instead of previous VO CB/VSS (1952-1957) so your knife is c.1957.
I believe that you are correct.
-
Sorry, MiniChamp, I forgot to show another side of this knife. It has fiber scales and older style can opener. I'll ask Rene show us blade stamps when he come back from his Switzerland trip.

-
@jnoxyd said:
Sorry, MiniChamp, I forgot to show another side of this knife. It has fiber scales and older style can opener. I'll ask Rene show us blade stamps when he come back from his Switzerland trip.Very interesting. If it has fiber scales, I guess it's probably from the late 1930's. I have never seen a right-weighted saw on a Victorinox SAK from around this time before. It would indeed be great to see the blade stamps on this SAK. Thanks!
-
Blade stamps of knives shown above from Rene ES aka Der Eidgenosse


-
Sir, you are one diligent person! Hats off

-
@jnoxyd said:
Blade stamps of knives shown above from Rene ES aka Der EidgenosseThanks, Jnoxyd!
These images are very interesting. The SAK with the fiber scales (the second from the top) now looks to me even more intriguing. I have seen its blade stamps (VICTORIA-SWITZERLAND-STAINLESS on the front, nothing on the back) on several SAKs from the early 1950's, such as the 1950's model 246aU that you show in this post, but never before on a SAK with the pre-1946 can opener and/or with fiber scales. -
Hi, MiniChamp, here's one more saw to your pics collection, Woodsman mid.1950s

-
Great information and photos
thanks for sharing -
Hey Minichamp. If I may ask for your help a minute sir? I recently obtained what I believe is the mid 50s Woodsman or 236u with the 19+20 tooth saw blade. Over all pretty good condition and trying to determine value to sell or trade.
I'm not a collector and if I keep it it'll get careied and used. I'm sure someone who collects them would appreciate it more.
Since you are the only person who seems to even know this model exists. Or at least that I can find(lol) I hoped maybe you could help or point me in the right direction.
Also, awesome post. Very interesting material.
Thanks in advance.
Shrub. -
@Shrubberryman said:
I recently obtained what I believe is the mid 50s Woodsman or 236u with the 19+20 tooth saw blade. Over all pretty good condition and trying to determine value to sell or trade.Welcome to the forum! I think that SAKs of the type that you describe (in good condition) usually sell on eBay for prices in the $50-$200 range. It can depend on how good the condition really is and on the dynamics of the bidding.
-
Great thread...great photos and excellent information. I enjoyed it a lot.

-
An interesting Victorinox SAK was sold on eBay about a month ago and can be seen in the attached image. It's a model 237 with fiber scales that I believe to be from the early 1930's (or mid-1930's). What makes this SAK extremely interesting in the context of this thread is that it has a wood saw with 29 teeth. (While it's hard to be sure without access to the actual SAK, I believe that this saw fits the above introduced system of type designations as being of type SN29ALSP.) Before seeing this SAK, I have only seen wood saws with 27 teeth on pre-1950's 90mm Victorinox SAKs, so this is very unusual (and also unexpected) from my perspective. Has anyone seen such saws with 29 teeth on other pre-1950's Victorinox SAKs?
It should be pointed out that there is also another thing that makes this SAK interesting: it has a cap-lifter along with the slanted JNOXYD tang stamp (j2 stamp in Ulli's table). In my limited experience, this is relatively uncommon (since most SAKs with the slanted JNOXYD tang stamp have the older screw driver without a cap-lifter) and suggests that this SAK may be among the earliest Victorinox SAKs with a cap-lifter. For this reason, images of this SAK were already posted in another thread by Jnoxyd.

-
@MiniChamp said:
I recently managed to obtain SAKs with two types of wood saws that were previously missing
(the April 2018 version of the table had place holders for these types, but no images). I am thus posting an updated table.Excellent thread! Been following it since I was lurking.
I've found a variant of the 29 tooth that fits between these two:

From a Late '50s/pre-'61 Woodsman 236U:

Teeth are machined like the SW29ARSP, but no nail nick like the SW29ARNP and has a polished finish. Tang stamps are VSSR/VOS. Bird head spacer is aluminum. Shackle is the 'flat' style.
While I'm in here...I also think the change for the two symmetrical teeth types happens c. '78/'79, based on my CAMPING and Hoffritz inlay study, where the bulk of samples have wood saws. All the knives I can positively put in the c. '80 range already have the new saw and have a fairly even sample from the '78/'79 range so I'm fairly sure the transition happens there and likely in the middle, late '78 to early-mid '79. Confirmed by samples of late 'V1' Hoffritz inlays, where the old style may have been in a 'disposal' phase and already off from main line use. Also confirmed after plastic tweezer head transition c. '78.
-
@kamakiri said:
Excellent thread! Been following it since I was lurking.Thanks!

I've found a variant of the 29 tooth that fits between these two:

From a Late '50s/pre-'61 Woodsman 236U:

Teeth are machined like the SW29ARSP, but no nail nick like the SW29ARNP and has a polished finish. Tang stamps are VSSR/VOS. Bird head spacer is aluminum. Shackle is the 'flat' style.
Thanks for sharing this information. If I understand correctly, the saw that you show has all the features that makes it what I call a saw of type SW29ARNP. Hence, this is what I call it. There are always some production variations in the sizes of teeth and some other length parameters. Older SAKs tend to have bigger variations. As an example, the first attached image shows two saws of type SN27ALSP with some easy to see differences between them. They are both on SAKs that may be from the 1920's or early 1930's (stainless with fiber scales and screw drivers without cap-lifters). I consider them to be different production variations of the same basic type (SN27ALSP).
By the late 1950's the variations are smaller, but seem to still be noticeable. The second attached image, for example, shows a saw of type SW29ARNP with teeth that are smaller than the teeth on the type SW29ARNP saw in my above table. (It's on a SAK that has the older style big awl along with a NS spacer and a bail of the latest style). The saw that you show seems to me like a variation in the other direction (bigger teeth). I consider all three of them to be production variations of the basic type SW29ARNP.
Note that as far as I can tell, it's not impossible that the first generation of type SW29ARNP saws had bigger teeth in a way that may be used to characterize a legitimate sub-type. In order for me personally to adopt such a view, however, I would need to see convincing evidence that the various saws of type SW29ARNP can be unambiguously divided into two types (this would likely require looking at many samples and verifying that the variations within each sub-type are small in comparison to the differences between the sub-types) and that the type with the bigger teeth really came before the other one. Since I'm not aware of such evidence at this time, I consider all of the saws with features that make them qualify as type SW29ARNP to be of the same type and I interpret differences between them as production variations.
While I'm in here...I also think the change for the two symmetrical teeth types happens c. '78/'79, based on my CAMPING and Hoffritz inlay study, where the bulk of samples have wood saws. All the knives I can positively put in the c. '80 range already have the new saw and have a fairly even sample from the '78/'79 range so I'm fairly sure the transition happens there and likely in the middle, late '78 to early-mid '79. Confirmed by samples of late 'V1' Hoffritz inlays, where the old style may have been in a 'disposal' phase and already off from main line use. Also confirmed after plastic tweezer head transition c. '78.
Thanks for sharing your findings. In essence, they seem to be consistent with my own observations. While it's probably not really meaningful to date such a transition with great precision (these things take time and may involve somewhat different times for different models), it's certainly convenient to be able to assign to it a concrete year. The practical question then becomes: which year is most suitable? I tend to agree that 1979 is likely to be the most suitable.


-
I recently managed to obtain a (pre-1923) carbon steel model 236. Hence, I now have a SAK with a narrow-form left-weighted saw that is made of carbon steel and has 27 asymmetric teeth and a standard nail nick. I was thus able to remove the last place holder from the previous version of the table and complete it.
Due to corrosion, I cannot tell what was the original finish of this carbon steel saw (it may have been polished, once upon a time, but I cannot really know this now). Hence, I'm calling this saw type CN27ALS?, where the question mark indicates not knowing what was the original finish. The resulting completed table is in the first attached image. Unfortunately, I couldn't really attach the table that I prepared with the same resolution as before, because it seems that the maximal allowed size of attachments here was recently reduced by 50% to 512KB. (Why? It really sucks.) Hence, I'm attaching a shrunken version.This completion of the previous table is far from being the end of story, however. As already noted above, there seem to exist 90mm Victorinox SAKs from the early 1930's with saws that have 29 teeth. In fact, I recently witnessed another such SAK getting sold on eBay. It is shown in the second attached image. On top of this, as already noted in the opening post of this thread, the upper SAK in the third image of this post (WARNING: it's a picture-heavy link) on Couteaux du monde looks like a very early (carbon steel) Victorinox SAK with a right-weighted saw. Hence, I expect that there should be at least one more type of a carbon steel saw (a right-weighted one; mine is left-weighted like the ones on most pre-1940 Victorinox SAKs). In other words, I expect that there are at least two more types of saws that should be in my table, but are not there yet. C'est la vie.


Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login