September Storm: 30 days of Waves
-
Spoiler:
@Dutch_Tooler said:
Awesome pics uploaded for Day 12/13, guys
I especially like the Damascus blade on Paul's golden Wave
Day 13
I'll just add some more prosaic ones. A few participants have remarked on the differences between the teeth on the pliers of older and newer Waves. As expected my new Wave + (in BO) has the coarser teeth and in fact the opposing teeth seem more widely apart, leaving a noticeable gap between them, except at the very tip. Also, the edges seem to be sharper than I have seen on older model Waves. This may well account for the difficulties in opening metal foil lids encountered by CallsignBadger.
I've added a pic of the Rebar pliers head on my ReWaveR, partly as a reference to my post of yesterday but also to compare with the Wave +. Not only is the Rebar head more voluminous generally (which should help overall stiffness and strength, if the metal used is the same), there also appears to be closure between almost all of the teeth along the entire length of the grip area. One would theoretically expect this to cause less of the troubles found by CallsignBadger, but I haven't tested this yet (I rarely use cream).
So at least for fine work the older G2 Wave and Rebar heads would appear to be more suitable. Anyone have any idea or experiences to share if they have encountered any advantages to the new design (except for the obvious one, for Leatherman that is, that the new ones are likely cheaper to produce >:D)?

Douglas, on your pic do I see correctly that there is a tapering gap between opposing teeth of the OG Wave plier head? I don't own one so can't verify this.
The problem with the foil lid is that there is only contact at the very tip of the plier. The aggressive teeth would’ve been fine for the task if only they toucched eachother. The reason the foil ripped is because of the one contact point being so small, so there was a lot of pressure on one point. The SOG Powerlock that finished the job had more ‘traditional’ needle nose texturing.
I actually really like the new design of the pliers. The tips are amazing at fine work, the teeth don’t really get damaged, and they grip really well.
But if they just touched, they would be perfect.
And just so you know, it seems all 2018 production Waves have these teeth. My non-plus does.
-
I still don’t get why there is a gap and
the pliers only touch at the tip of the pliers
I would like to know what the benefits are
-
If you open them up just a small amount then they are parallel to each other which would make the teeth actually grip better for smaller objects but not objects as thin as the foil
Most LM pliers are like that with the exception of a few every now and then 
-
Today I was going to check the tyre pressure
on my bike so I grabbed the pressure gauge
But it has stopped working :ahhhSo I used the Wave and the small screwdriver
to remove the screws so I can see what batteries it will take
And hopefully get some new batteries todayNo problems using the small driver
But had to use the flathead as the crosshead was too smallAnother example for the mini screwdriver

Would the #1 Phillips from your new bit kit have worked too?
-
@Jaypeebee said:
Day 13Used the pliers to remove a broken screw, although it did the job (eventually) I struggled with the pliers slipping off a few times! If I'd have had my Crunch with me, I'd have got the job done a lot quicker and easier.
To be honest, it would have been just the same with any normal plier based tool....!!!You'll be my main reference for the pliers usage in this challenge I guess. You seem to use it a lot

-
Day 13
Used the serrated blade to open a package.
It went through without any resistance...
-
-
@MTMatt said:
Day 13
Today I was going to check the tyre pressure
on my bike so I grabbed the pressure gauge
But it has stopped working :ahhhSo I used the Wave and the small screwdriver
to remove the screws so I can see what batteries it will take
And hopefully get some new batteries todayNo problems using the small driver
But had to use the flathead as the crosshead was too smallAnother example for the mini screwdriver

Would the #1 Phillips from your new bit kit have worked too?
It probably would fit
but I was only carrying the Wave today
-
September Storm :

Got out for a nice hike in the hills this morning. Wave didn't get used for anything, but I did pause to get a quick glamour shot.
-
Nice pic Nix

-
Thanks, W.
I'm not getting all the great uses in that you guys are, but I'm having fun toting the Wave around. It's a nice tool to have in one's pocket.

-
I'm not getting all the great uses in that you guys are, but I'm having fun toting the Wave around. It's a nice tool to have in one's pocket.

Can’t be easy to use the Wave
everyday when you are busy travelingI like the Wave+ so far
done everything I wanted it to do
Now I want to try the Surge :D -
@MTMatt said:
Day 13
Used the pliers to remove a broken screw, although it did the job (eventually) I struggled with the pliers slipping off a few times! If I'd have had my Crunch with me, I'd have got the job done a lot quicker and easier.
To be honest, it would have been just the same with any normal plier based tool....!!!You'll be my main reference for the pliers usage in this challenge I guess. You seem to use it a lot

Thanks Matt

It's probably the job I do, seem to need pliers quite a bit
-
Nix, Nice glamour shot!
Love that BO !Day 13:
Cut an orange for Some vitamine juice..
Serrated blade prefect for that job.
-
Some great posts here guys. Keep up the good work with the challenge

-
Another awesome day guys
Having a great time with this challenge myself 

-
Day 13 of 30
I was looking to see what kind of coupons I had to use at lunch today and ended up getting a BOGO on 2 combos
I for me and a other for my dad 
<a href="https://flic.kr/p/29WHV95" target="_blank" rel="noopener noreferrer"><img src="https://farm2.staticflickr.com/1854/43938815824_257a10fda1_k.jpg" alt="banner" style="max-width: 100%; height: auto;" /></a>2018-09-13_09-47-49 by Poncho 65, on Flickr
And a beauty shot since it was an OG Wave

<a href="https://flic.kr/p/Mhb5X6" target="_blank" rel="noopener noreferrer"><img src="https://farm2.staticflickr.com/1875/29719086267_740c0c694c_k.jpg" alt="banner" style="max-width: 100%; height: auto;" /></a>20180913_091932 by Poncho 65, on Flickr
-
Great uses, peeps


-
Day 13 - Wave at work, used the SE to cut cardboard to fit as shelf liners in store room, completed 5 of 8 shelves before I ran out of cardboard.
Then at home used to open mail and also took picture of plier head since some have been indicating an issue with the gap behind the nose. I had contributed several pictures of the gap on several of my MTs. I remember my OHT gap is a bit wider than any of the others. My SOG Paratool however ( all 4) the pliers teeth align perfectly fitting as a tongue and grove joint, I could grip a tissue paper and leave indentations when released.
I am missing my Rebar during this challenge, as I like the screw drivers selection as well as the blade length over the Wave's bit length. And the extension is to thick to access screws on several connectors I utilize. Miss the AWL not realizing how much I do deploy for tasks saving my blade for actual cutting and trimming. I will continue with the WAVE, but just saying it is not my #1 go to MT for EDC.


-
Day 13:
We got in an antique scale (doing aesthetic restoration tomorrow). One piece of linkage for the balance-carriage was missing. So, the inner-dimensions have to be exact. I made a piece out of streel rod and heat-darkened it. Used the pliers and file on the Wave. The pliers were to hold it to the heat. The hardened steel was far too strong for MT(I wouldn't have attempted to bend it with my Surge) pliers to bend without damage. Used two 10' utility pliers for the bends and thr vise for the flattening. The Wave file works great for smoothing metal. :)




Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login