September Storm: 30 days of Waves
-
Day 13 - Wave at work, used the SE to cut cardboard to fit as shelf liners in store room, completed 5 of 8 shelves before I ran out of cardboard.
Then at home used to open mail and also took picture of plier head since some have been indicating an issue with the gap behind the nose. I had contributed several pictures of the gap on several of my MTs. I remember my OHT gap is a bit wider than any of the others. My SOG Paratool however ( all 4) the pliers teeth align perfectly fitting as a tongue and grove joint, I could grip a tissue paper and leave indentations when released.
I am missing my Rebar during this challenge, as I like the screw drivers selection as well as the blade length over the Wave's bit length. And the extension is to thick to access screws on several connectors I utilize. Miss the AWL not realizing how much I do deploy for tasks saving my blade for actual cutting and trimming. I will continue with the WAVE, but just saying it is not my #1 go to MT for EDC.


-
Day 13:
We got in an antique scale (doing aesthetic restoration tomorrow). One piece of linkage for the balance-carriage was missing. So, the inner-dimensions have to be exact. I made a piece out of streel rod and heat-darkened it. Used the pliers and file on the Wave. The pliers were to hold it to the heat. The hardened steel was far too strong for MT(I wouldn't have attempted to bend it with my Surge) pliers to bend without damage. Used two 10' utility pliers for the bends and thr vise for the flattening. The Wave file works great for smoothing metal. :)




-
** Day 13 **
Got home late, so no action.
But a nice pic for you all


-
G-Man the Blacksmith.


-
Day 13
FAMILY TREE

-
Thank you, Douglas!

Maybe more of a "Greysmith". I know enough to be dangerous.

BTW, I also just posted your family tree photo to the Sept. calendar thread.

@CallsignBadger said:
** Day 13 **
Got home late, so no action.
But a nice pic for you all

Nice pic, CsB!

If it were landscape, I would have posted it to the calendar thread.
Also,
Great uses and photos, everyone! This is definitely one of the better challenges I have partaken in.
-
Day 13
Busy day on the desk no work for wave today so photo shoot time

-
DAY 13 .. Taro tonight


-
Heck yes, good choice Obi.

-
Day 13
Used the Wave + to open the post.
<a href="https://flic.kr/p/29EGPkF" target="_blank" rel="noopener noreferrer"><img src="https://farm2.staticflickr.com/1842/43757537265_2a60b992f9_k.jpg" alt="banner" style="max-width: 100%; height: auto;" /></a>20180913_203949
Blades been getting a lot of use, still holding up great !
<a href="https://flic.kr/p/29XyhaN" target="_blank" rel="noopener noreferrer"><img src="https://farm2.staticflickr.com/1888/43948251944_b32b052a5f_k.jpg" alt="banner" style="max-width: 100%; height: auto;" /></a>20180913_204035
-
I was working on one of my CO2 airguns tonight and realized I probably took better care of it than my Bersa Thunder 380. The 380 wasn't THAT dirty, but it needed some TLC.

Wave to the rescue. Well. Kind of. I didn't feel it needed a full break down yet, so just a superficial cleaning and supplemental oiling.




-
DAY 13
With 25 min to spare. no action today.

Sent from my iPhone using Tapatalk
-
Day 13
A speed wrench is one of my favourite tool in my work belt. Prefers this way over adjustable wrench.

-

**Day 14 **
I've never been very happy with the sheath Leatherman shipped with the Gen 2.1 Waves, as this would fit just the Wave in the main compartment, with some additional room in just one stretch nylon side pocket. This might be OK with an unmodded Wave but I find the ReWaveR is not quite complete without a small bit set and removable bit driver to go over the fixed Phillips.
So yesterday I set about devising a new carry method. I had a spare LM "large premium leather" sheath I had used for my Surge, before it became the Surge-R and found more space in its own Skinth. It turned out that the flap of the LM sheath could be shortened to snugly let a Wave with bit kit fit inside the main compartment, while it also had space for a new snap button if the flap was cut off just short of the opening of the old snap button.
Of course I cut the flap off with my ReWaveR's sharp 154cm blade - went through the leather like the proverbial butter. The edges are still a bit rough and not blackened yet, but the result is in the pics below.



-
Day 14
Scavenged some handles.

-
Hello there
Beginning to think my life is boring as there was also little LM action for day 14.
Tomorrow will be better as it is Land Rover day and with a '64 shorty there is always a job to do.Pics of both tomorrow then !!
-
Excellent pics and uses everyone

-
Day 14
Working on an intensifier for a water jet cutting system today.
The fine precise tips of the pliers are perfect for retrieving small delicate items.
The can opener comes in handy too for removing seals!


-
Nice uses there, JPB!

Good work, G-man!
-
Paul, I figure some days I need a multitool, some days I don't. But I always carry one (SAK or pliers-based) because you just never know what kind of a day it will be!

Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login