Skip to content
Collapse
? [[global:guest]]
Unread Recent
HOME SEARCH PROFILE NOTIFICATIONS 0 MESSAGES 0 BOOKMARKS MEMBERS BADGES
Multitool.Org Forum
MultiTool.org • Community Header Space • Watch This Space

Holy crap what a day....

Scheduled Pinned Locked Moved The Outdoor and Survival Forum
98 Posts 1 Posters 5.2k Views
  1. Home
  2. Outdoor Section
  3. The Outdoor and Survival Forum
  4. Holy crap what a day....
Holy crap what a day....
  • Oldest to Newest
  • Newest to Oldest
  • Most Votes
Reply
  • Reply as topic
Log in to reply
This topic has been deleted. Only users with topic management privileges can see it.
  • Grant Lamontagne Offline
    Grant Lamontagne
    administrators
    Posts: 67,980
    Grant Lamontagne Offline
    Grant Lamontagne
    administrators
    wrote on last edited by
    #82 Quote Reply

      Just to update this thread a little.....

      First off, the painful bit. The coupler DOES fit a 2" ball, it just has to go completely straight down on it, which I can't do because of the spare tire on the Jeep. If I open the back door and hook up the trailer it works fine. That means that the day I brought it home on the highway was extra dangerous because I was using a ball that was too small for the trailer.... with no safety chains.... :ahhh

      The trailer is finally repaired (I hope) although I still may need an extra bit welded on to the tongue to fit in the bracket so it doesn't sway wildly, but I'll deal with that in the spring. In a couple of weeks I am going to drive 650kms with it to store it at my parents' place, and it should be fine enough for that, even if I have to shove a work glove or something in the bracket to keep it from swaying. Currently I have some neoprene pads in there but I really don't expect them to last too long.

      I have bought new safety chains and hooks and the bolts I had to attach them were too big to fit through the chain, so I am now using slightly smaller bolts. I'm not happy about that and may grind the extra few millimeters I need in the chain later on, but it'll do for now.

      I have rewired the whole trailer. The wiring in it was a mess- the trailer uses a 4 pin connector to connect to the Jeep, and halfway down the length of the trailer it stopped at two four pin connectors, which led to a six pin connector which then went to the two tail lights. :facepalm:

      I ripped all of that out and ran dedicated wiring to each tail light to simplify matters. I also ran some PVC conduit under the trailer to protect the wiring, but, as I am terrible with wiring the whole mess didn't work once I was done, and I ended up calling my cousin to check it for me. It was a stroke of luck that he happened to be in the neighborhood and was here in just a few minutes. He is a mobile mechanic and actually goes to wherever you are broken down to repair your vehicle, and I caught him at exactly the right time. Finally, some good news! :D

      Twenty minutes later he diagnosed it as a bad harness, but luckily there were several other harnesses embedded in the old wiring, so we cut one of those out and replaced the one that I had replaced on it a few months ago. I really need to stop loaning my trailer to my landlord, as I have to replace the harness after every tie he uses it.... :facepalm:

      To counteract the sway issues, I have tried filling the gaps around the tongue with some neoprene and silicone pads used for furniture. I don't expect them to last long, but as I got them from the dollar store, I am not too worried about replacing them. They should manage until I find a more permanent solution.

      Anyways, I will be off to test everything shortly! Wish me luck, because I really don't want to have to add to this story again!

      Def


      1 Reply Last reply
      • powernoodle Offline
        powernoodle
        Posts: 7,103
        powernoodle Offline
        powernoodle
        wrote on last edited by
        #83 Quote Reply

          @Grant Lamontagne said:
          So in short, whether successful or not, tomorrow is going to be another busy one...

          This is why I never leave the house.

          :salute:

          1 Reply Last reply
          • Mechanickal Offline
            Mechanickal
            Posts: 14,690
            Mechanickal Offline
            Mechanickal
            wrote on last edited by
            #84 Quote Reply

              Good luck, stay safe!

              1 Reply Last reply
              • Syncop8r Offline
                Syncop8r
                Posts: 8,801
                Syncop8r Offline
                Syncop8r
                wrote on last edited by
                #85 Quote Reply

                  Good luck! :tu:

                  Spoiler:
                  :popcorn:

                  1 Reply Last reply
                  • Grant Lamontagne Offline
                    Grant Lamontagne
                    administrators
                    Posts: 67,980
                    Grant Lamontagne Offline
                    Grant Lamontagne
                    administrators
                    wrote on last edited by
                    #86 Quote Reply

                      Lights still didn't work so I picked up a new harness today. I don't trust the old harness i had to use.

                      Def


                      1 Reply Last reply
                      • redmond Offline
                        redmond
                        Posts: 325
                        redmond Offline
                        redmond
                        wrote on last edited by
                        #87 Quote Reply

                          @Grant Lamontagne said:
                          Lights still didn't work so I picked up a new harness today. I don't trust the old harness i had to use.

                          Def

                          Shot in the dark - check the fuse(s) too.

                          1 Reply Last reply
                          • Grant Lamontagne Offline
                            Grant Lamontagne
                            administrators
                            Posts: 67,980
                            Grant Lamontagne Offline
                            Grant Lamontagne
                            administrators
                            wrote on last edited by
                            #88 Quote Reply

                              @redmond said:

                              @Grant Lamontagne said:

                              Lights still didn't work so I picked up a new harness today. I don't trust the old harness i had to use.

                              Def

                              Shot in the dark - check the fuse(s) too.

                              Always a good plan.... thanks for the reminder. :tu:

                              Def


                              1 Reply Last reply
                              • Grant Lamontagne Offline
                                Grant Lamontagne
                                administrators
                                Posts: 67,980
                                Grant Lamontagne Offline
                                Grant Lamontagne
                                administrators
                                wrote on last edited by
                                #89 Quote Reply

                                  The Curse of Lac LaPeche strikes again. :facepalm:

                                  Once again Megan and I decided to go and paddle around Lac LaPeche. It was a pleasant paddle in the past, and, despite the above issues, we felt it was worth another shot. Little did we know that the Curse of Lac LaPeche wasn't done with us.

                                  It started out as a nice enough paddle. We did a good chunk of the northern part of the lake. It was overcast, but expected to clear, and it was also pretty hot (either high 20's or low 30's) so no complaints even if it did rain a little. We visited Megan's old camp site, and scouted some other spots on the shore that looked interesting, and generally had a pretty good time.

                                  As usual I was amused at how color coordinated Megan and I are in the Point 65 boat she usually paddles and the new Sun Flight kayak I recently picked up- of course, they paddle entirely different, but they look neat together.

                                  This was where Megan and Sarah camped last year- the beaver lodge may have gotten bigger, or it may just appear that way since the water seemed a lot lower this year. Either way, I didn't get any photos last year because I was too busy dealing with.... well.... everything else! :ahhh

                                  Other than being a bit overcast, the weather was great- not even a slight breeze, so the water barely had a ripple on it. It was so serene that it was almost boring....

                                  We landed on a few nice beaches here and there to see if there were wild blueberries or other tasty edibles, but alas, no such luck. After several hours of paddling and exploring the large lake, we headed back, loaded up the trailer and headed for home, having seemingly escaped The Curse.

                                  Nope.

                                  Shortly before reaching home the trailer started to sway a bit, and at first I attributed it to wind or potholes. We were, after all, still in Quebec, a province famous for not maintaining roads or infrastructure. It got pretty bad at one point, but we were only a few blocks from home, so I kind of babied it until we got to our driveway, and I went to back the trailer into our spot. That's when I noticed the passenger side wheel wobbling. Badly. :facepalm:

                                  I had destroyed a wheel bearing so badly that it kicked off the grease cap and vomited grease all over the wheel.

                                  ![](http://gallery.multitool.org/var/resizes/Defventures/Lac-La-Peche/September-12%2C-2018/Curse of Lapeche (7).jpg?m=1537197718[/img

                                  I was sure that I'd serviced these bearings at the beginning of the season, but it appears from the mess that I forgot, and apparently only did the bearings on the Apache, and not on my utility trailer. I pulled off the hub and there were just fragments of the bearings left in the grease.

                                  [img]http://gallery.multitool.org/var/resizes/Defventures/Lac-La-Peche/September-12%2C-2018/Curse of Lapeche (5).jpg?m=1537197717)

                                  I cut my fingers pretty good on jagged metal as I tried to haul out what was left of them to clean the hub and install new bearings, and I even had to cut the old bearing housing off the spindle as it had gotten so hot it pretty much fused on. Thank the Maker for my Dremel tool! We then headed off to Canadian Tire for replacement bearings and some fresh grease.

                                  After we got back, the next problem was trying to remove the race from the hub, and Megan and I took turns pounding on it for a couple of hours before we admitted defeat. The heat that was generated that fused the housing to the spindle also apparently fused the race to the hub, which meant new hubs were needed, so we went to Princess Auto for those. It's a bit further away, but they are more likely than Canadian Tire to have the hubs I need.

                                  Naturally they didn't have a direct replacement for my big, heavy cast iron ones, so I had to try and locate a suitable replacement set. Since I know nothing at all about how to size these things, I grabbed an employee and asked him. Soon we had three employees around us, all arguing over what we needed, and, as it turned out, all of them were barking up the wrong tree. :facepalm:

                                  As the store was closing for the night (it was now almost 9 pm) we left without buying anything, and, as I drove home, Megan started searching the Internets for the answer.

                                  By the next morning, she believed she knew what we needed, and she insisted that we go to the other Princess Auto in town so as not to be confused by the people that should have known. We got there, spoke to another employee, who confirmed what Megan believed was the correct set of parts and we left.

                                  It's important to point out that I can build just about anything, as long as I have the right parts, so I would have been lost without Megan's insights into the correct parts. As it turned out, the bearings that came with the kit had the correct size external ring, but were sized for a larger spindle, and so had an incorrect internal ring size- luckily I had purchased the correct bearings at Canadian Tire the day before, so the good news was that I finally had all the right parts. The bad news is that the bearing kits from Canadian Tire cost a pretty penny, and the hubs weren't exactly cheap either, so I had been hoping to be able to return the original bearing kits and get some of my money back. That wasn't in the cards though, and this whole repair cost me well over $200. :facepalm:

                                  But, with all of the correct parts, it didn't take long to grease up the bearings, races, seals and collars and install them. The new hubs are sharp looking and also weigh a fraction of what the old ones did, so no complaints from me. I did one side while Megan took care of the undamaged side (I wasn't going to just replace one side!) and we soon had it back up and running- or so we'd hoped, because we actually were supposed to spend a couple of days at a friend's cottage, almost two hours away, and we needed the trailer for that!

                                  We stopped every twenty minutes or so to check to see if the bearings were heating up, leaking grease or had any other telltale signs, but it performed like a champ, just as I have come to expect from my trusty utility trailer!

                                  The Curse of LaPeche got us again and cost me some money and time, but at least I got to deal with it in the comfort of my own driveway this time, and at least we got to enjoy a nice paddle first!

                                  Def


                                  1 Reply Last reply
                                  • SteveC Offline
                                    SteveC
                                    Global Moderators
                                    Posts: 73,535
                                    SteveC Offline
                                    SteveC
                                    Global Moderators
                                    wrote on last edited by
                                    #90 Quote Reply

                                      Nice pics and a good ending :like: :tu:

                                      1 Reply Last reply
                                      • Mechanickal Offline
                                        Mechanickal
                                        Posts: 14,690
                                        Mechanickal Offline
                                        Mechanickal
                                        wrote on last edited by
                                        #91 Quote Reply

                                          You did all this with just a Spartan and some gun powder, right?

                                          1 Reply Last reply
                                          • ducttapetech Offline
                                            ducttapetech
                                            Posts: 18,707
                                            ducttapetech Offline
                                            ducttapetech
                                            wrote on last edited by
                                            #92 Quote Reply

                                              Glad it worked out Boss. Nice pics btw.

                                              1 Reply Last reply
                                              • AimlessWanderer Offline
                                                AimlessWanderer
                                                Posts: 17,518
                                                AimlessWanderer Offline
                                                AimlessWanderer
                                                wrote on last edited by
                                                #93 Quote Reply

                                                  For you, that sounds like a very successful day mate :D

                                                  Is there anything left of the old trailer, or have you replaced it all now :P

                                                  All joking aside, glad you got it sorted a lot quicker than in some of your previous escapades :cheers:

                                                  1 Reply Last reply
                                                  • Alan K. Offline
                                                    Alan K.
                                                    Posts: 8,225
                                                    Alan K. Offline
                                                    Alan K.
                                                    wrote on last edited by
                                                    #94 Quote Reply

                                                      You know, a can or two of spray paint wouldn't cost very much. We use the black, high temperature, BBQ grill paint for touching up scratched Jeep bumpers after trail rides, and it would also work a treat on your trailer. :pok:

                                                      1 Reply Last reply
                                                      • Grant Lamontagne Offline
                                                        Grant Lamontagne
                                                        administrators
                                                        Posts: 67,980
                                                        Grant Lamontagne Offline
                                                        Grant Lamontagne
                                                        administrators
                                                        wrote on last edited by
                                                        #95 Quote Reply

                                                          @Mechanickal said:
                                                          You did all this with just a Spartan and some gun powder, right?

                                                          I'd have traded a Spartan for some useful help at the store, does that count? :-P

                                                          Def


                                                          1 Reply Last reply
                                                          • Grant Lamontagne Offline
                                                            Grant Lamontagne
                                                            administrators
                                                            Posts: 67,980
                                                            Grant Lamontagne Offline
                                                            Grant Lamontagne
                                                            administrators
                                                            wrote on last edited by
                                                            #96 Quote Reply

                                                              @50ft-trad said:
                                                              For you, that sounds like a very successful day mate :D

                                                              Is there anything left of the old trailer, or have you replaced it all now :P

                                                              All joking aside, glad you got it sorted a lot quicker than in some of your previous escapades :cheers:

                                                              Well....

                                                              The deck and body are still original, although I need to replace the deck at some point as the wood is pretty rotten. Also the axle, hangers and springs are original, although I will admit to having given serious consideration to replacing all of that. A 1500lb axle (that included hubs) was on sale at Princess Auto for $125 and it seemed like a no brainer to get that instead of the two individual hubs at $65 each. The problem with that was that I currently have a 2000lb axle with 5 bolt hubs and 5 bolt wheels while the axle on sale was only 4 bolt, which meant that I would have had to either buy hubs on top of the axle, or buy three new wheels and tires too.

                                                              This is the most expensive $500 trailer I own.... although the Apache is a close second!

                                                              Def


                                                              1 Reply Last reply
                                                              • Grant Lamontagne Offline
                                                                Grant Lamontagne
                                                                administrators
                                                                Posts: 67,980
                                                                Grant Lamontagne Offline
                                                                Grant Lamontagne
                                                                administrators
                                                                wrote on last edited by
                                                                #97 Quote Reply

                                                                  @Alan K. said:
                                                                  You know, a can or two of spray paint wouldn't cost very much. We use the black, high temperature, BBQ grill paint for touching up scratched Jeep bumpers after trail rides, and it would also work a treat on your trailer. :pok:

                                                                  When I replace the deck (probably next year) I'm going to strip all the old paint off it and give it a good coat of bedliner.

                                                                  And then probably another good coat of bedliner, just because.....

                                                                  Def


                                                                  1 Reply Last reply

                                                                  Hello! It looks like you're interested in this conversation, but you don't have an account yet.

                                                                  Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.

                                                                  With your input, this post could be even better 💗

                                                                  Register Login

                                                                  • 1
                                                                  • 2
                                                                  • 3
                                                                  • 4
                                                                  • 5
                                                                  1. Home
                                                                  2. Outdoor Section
                                                                  3. The Outdoor and Survival Forum
                                                                  4. Holy crap what a day....
                                                                  Reply
                                                                  • Reply as topic
                                                                  Log in to reply
                                                                  COMMUNITY LINKS
                                                                  EDC-TV SAKWiki GearFeed SAKSelector
                                                                  Operational Funds

                                                                  Help us keep the Unworkable working!

                                                                  Make A Donation
                                                                  November Goal: $300.00
                                                                  Due Date: Nov 30
                                                                  Total Receipts: $0.00
                                                                  Below Goal: $300.00
                                                                  0% funded
                                                                  • Login

                                                                  • Don't have an account? Register

                                                                  • Login or register to search.
                                                                  • First post
                                                                    Last post
                                                                  0