September Storm: 30 days of Waves
-
Honestly, how often do you apply full force on entirely closed pliers?
Yes not often

-
Post above edited to clarify that I just ground off a tiny bit of the inner, facing surfaces at the very tips. Nothing off the length of the tips.
-
Thanks D_T I thought you did

-
-
There should be some weird-ish technical reason why LM choose to build their recent pliers tip in such a way.. Maybe someone write in to ask them about it?

One reason I can think of is to prevent slippage when u are pulling on something?
-
No idea

-
I get the feeling it might be a cost-saving measure. Just skipping the fine-tuning... There is no rational reason why at least the gripping surface's outer contour (i.e. not counting indents) should not be perfectly plane. Too much risk of damaging whatever you're gripping if it weren't... IMHO of course.
-
I'll be the contrary voice here.
I like the new design.
I like the way one can use just the tips for very precise gripping. If I need to grip something larger, I don't use the tips, but rather use the wider area of the jaws behind the tips. I feel that I get a bit more versatility from the current design.
True, the tips, having slightly taller teeth than the rest of the jaws, might be more prone to marking a surface that is gripped tightly. Something to consider. But I like those tall teeth and that very precise grip.
Has any one written to Leatherman asking about the tip design? It seems intentional to me, and not a lack of finishing. I might be wrong about that, but it seems consistent across awl of the Wave+'s we've seen and is precisely that last tooth set at the tips.
-
As I think about this a bit more, it seems that awl pliers are designed with jaws that are angled together in order to meet at the tips.

So, except for one slight degree of opening, the jaws of any pliers are not parallel. Therefore, when gripping an object with parallel sides, e.g. a nut, there will awlways be one set of teeth that will make contact first and exert more pressure on the object being grasped.
Often a good reason to use a wrench instead of pliers.
-
I haven’t had any problems
yet with the new design pliers
It’s just the first time I have seen pliers like this
-
@Nix said:
I'll be the contrary voice here.I like the new design.
I like the way one can use just the tips for very precise gripping. If I need to grip something larger, I don't use the tips, but rather use the wider area of the jaws behind the tips. I feel that I get a bit more versatility from the current design.
True, the tips, having slightly taller teeth than the rest of the jaws, might be more prone to marking a surface that is gripped tightly. Something to consider. But I like those tall teeth and that very precise grip.
Has any one written to Leatherman asking about the tip design? It seems intentional to me, and not a lack of finishing. I might be wrong about that, but it seems consistent across awl of the Wave+'s we've seen and is precisely that last tooth set at the tips.

-
Today I didn’t think I was going to need the Wave+
but when I tried to remove the hose connector
from the tap after the summer use it was stuck
so used the pliers to undo the connectorNo real problem but the pliers only just fitted
which made holding the Wave+ a bit of a challengeNice one Wspeed

"...the pliers only just fitted..."
I noticed that too 4 days ago.
I then had a look the Rebar and Surge and dare to say that they would not have been able to do it. -
@MTMatt said:
Day 22
Today I didn’t think I was going to need the Wave+
but when I tried to remove the hose connector
from the tap after the summer use it was stuck
so used the pliers to undo the connectorNo real problem but the pliers only just fitted
which made holding the Wave+ a bit of a challengeNice one Wspeed

"...the pliers only just fitted..."
I noticed that too 4 days ago.
I then had a look the Rebar and Surge and dare to say that they would not have been able to do it.That’s a surprise I would of thought as they
are bigger that they would of been able to grip the piece
I will have to try the PocketCrunch as that can grip up to 1 inch

-
Day 22
Amazingly I had some use for the mini screwdriver today. It came in handy getting out the drained lithium cell of my bike speed sensor



-
@Nix said:
As I think about this a bit more, it seems that awl pliers are designed with jaws that are angled together in order to meet at the tips.
So, except for one slight degree of opening, the jaws of any pliers are not parallel. Therefore, when gripping an object with parallel sides, e.g. a nut, there will awlways be one set of teeth that will make contact first and exert more pressure on the object being grasped.
Often a good reason to use a wrench instead of pliers.
That is a correct observation, a bit of taper in the space between closed jaws is usual. I just didn't like the hooked tip ends too much. The minimal grinding I did just got rid of those. There is still a bit of taper left.
-
Day 22/30
No really much use for Wave today, used scissors to cut few finger nails and sliced banana ( just first played with banana so my daughter could eat it)

Only Tools Matters

-
Good one Antti

-
Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login
