Wave blade closing problem
-
Some of you might remember that I had a problem with a bent metal file on my New Wave a while back. Well, I decided to send my Wave in to have it repaired on warranty. I also asked them to fix a small problem with the liner lock not engaging properly on the PE blade.
I just received my Wave back. They fixed both those problems, but the PE blade now bangs against the inside portion of the handle when closing it. It makes contact about 1/2" from the tip and then scrapes closed.
I can still open and close the blade with OH, but the cutting edge is making contact and will get damaged in time.
Does anyone know a quick fix for this, or do I have to go through another waiting period with warranty?
-
I noticed this on two Charge TTi's I've had.. You could file down the knife tip a little bit; then it won't come in contact anymore. At least that's what I did.
-
@Leatherman123 said:
I noticed this on two Charge TTi's I've had.. You could file down the knife tip a little bit; then it won't come in contact anymore. At least that's what I did.Thanks but unfortunately, it starts scraping too far back from the tip to do that. I'd have to file off about 1/2". :)
-
I'd contact the warranty folks about it. Don't mention this forum though as they don't seem to like me very much...
Def
-
why dont they like you?
-
Loooong story. It has to do with the Canadian repair contractors, not LM themselves.
Def
-
-
you may not have been here for it, but if you do a search for XE6, you'll probably find a thread with a good portion of the story...
Def
-
Yeah, I am not too thrilled with the Canadian repair contractors myself at the moment either... :P
Spending another $10 postage so that they can fix their own mistake doesn't seem right.
I wanted to pick up some 5-point security bits anyway, so I'd rather put the money towards that. Can anyone point me to a cheap set online?
-
@max6166 said:
Yeah, I am not too thrilled with the Canadian repair contractors myself at the moment either... :PSpending another $10 postage so that they can fix their own mistake doesn't seem right.
I wanted to pick up some 5-point security bits anyway, so I'd rather put the money towards that. Can anyone point me to a cheap set online?
Multitool.org member eleatherman has them available here: http://www.eleatherman.com/index.php?main_page=product_info&products_id=84
(remember, you need two)
-
@max6166 said:
Some of you might remember that I had a problem with a bent metal file on my New Wave a while back. Well, I decided to send my Wave in to have it repaired on warranty. I also asked them to fix a small problem with the liner lock not engaging properly on the PE blade.I just received my Wave back. They fixed both those problems, but the PE blade now bangs against the inside portion of the handle when closing it. It makes contact about 1/2" from the tip and then scrapes closed.
I can still open and close the blade with OH, but the cutting edge is making contact and will get damaged in time.
Does anyone know a quick fix for this, or do I have to go through another waiting period with warranty?
Sounds to me as maintenance being lazy.
I think they've just loosened the pivot screw a bit so the linerlock works, but then you get another problem and that is a scraping blade.
To check if i'm right; open the blade, prevent the linerlock from locking it with your thumb as if you were going to close the blade, and now wiggle the blade carefully from side to side with your fingers.
There should be no bladeplay, but there probably is.What they should have done is exchange the blade for another one with a good fit, as there are minute differences in the bladeramps where the liner engages the blade.
But hey, what do i know ? :D
-
@kwakster said:
Sounds to me as maintenance being lazy.I think they've just loosened the pivot screw a bit so the linerlock works, but then you get another problem and that is a scraping blade.
To check if i'm right; open the blade, prevent the linerlock from locking it with your thumb as if you were going to close the blade, and now wiggle the blade carefully from side to side with your fingers.
There should be no bladeplay, but there probably is.What they should have done is exchange the blade for another one with a good fit, as there are minute differences in the bladeramps where the liner engages the blade.
But hey, what do i know ? :D
Thank you fo your expert opinion, Kwakster. As usual, you are absolutely correct.

It is definitely the same blade and there is side-to-side play. Actually, there is even more side-to-side play with the serrated blade and I discovered that my wood saw now hits the outer edge of the handle when closing as well.
I've got to admit that I am not very impressed with the Canadian warranty people at this point. How could they not notice that the PE blade they were asked to fix could not be closed properly?
You mentioned a trick a while ago back where you could fix the liner lock by filing the back of the blade a bit. I guess I'll just try that myself and get some 5-point bits to tighten things up again.
Thanks again.

-
Max, whatever you do, don't go filing on the back of the blade ( or the bladeramp as it is officially called)
To achieve a good fit with your current blade file a truly minute amount from the top of the liner itself.
A few strokes with a Spyderco Sharpmaker medium stick, or a thin piece of wood with some 400 grit SiC paper will probably do the trick.In the ideal situation the liner will seat itself completely on the bladeramp - but not further - thus allowing for room for wear.
This is what i aim for when doing blade changes and/or mods, but it doesn't always work out that way as sometimes they happen to travel a bit further. -
@kwakster said:
Max, whatever you do, don't go filing on the back of the blade ( or the bladeramp as it is officially called)
To achieve a good fit with your current blade file a truly minute amount from the top of the liner itself.
A few strokes with a Spyderco Sharpmaker medium stick, or a thin piece of wood with some 400 grit SiC paper will probably do the trick.In the ideal situation the liner will seat itself completely on the bladeramp - but not further - thus allowing for room for wear.
This is what i aim for when doing blade changes and/or mods, but it doesn't always work out that way as sometimes they happen to travel a bit further.Yikes! Thanks for clearing that up. :o :D :D
-
I'm glad you said that Kwakster, because that's what I was thinking. I think I would send it back with a really smurfty letter along the lines of "I know what you did, it's disgraceful, now do it properly please".
When you bought that tool Max - you paid for the warranty and service. I would demand it.
-
That happened to me with LM's warranty. I sent a SURGE in with a broken lock release, and they sent it back not fixed. They wanted me to send it back, and I MADE them send me a prepaid envelope! LOL
-
I think that's fair enough to be honest if they did a shoddy job. Leatherman strike me as the kind of company that would make it up to you if they screwed up anyway, although I guess the Canadian service centre don't share that ethos.
Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login
I've got time for a long story ::) ;) :D