Seeking Rebar modding advice.
-
Not a mod; but found this 2D bit kit at a local hunting & fishing store on sale, so I grabbed it.

I will likely try to come up with a “mod” way of storing it though
Sent from my iPhone using Tapatalk
-
Nice one MMR

Like to see what you come
up with for storing the flat bits

-
Okay, I am just testing an idea out here, so bare with me.
Zip tie moment 1:
With the bit kit, I want to keep the two bit holders together, mainly so when I reach for the bit kit it will be pulled out as one unit and not risk pulling out one and then dropping the other.
But also because the holders have a smooth side on the back, so they will go in and out of the sheath smoother and lower the risk of a bit getting caught.
I did this using small zip ties and shrink tube, to prevent the locks on the zip ties from moving in and tightening themselves more. I want to leave them a little loose so that it is easier to flip them over.



Zip tie moment 2:

So the bit kit fits perfectly into the single sheath my rebar came with.
So to test out an idea, I zip tied it to the side of the sheath for the Charge, like so:

Also this way I can still carry my 3D bits as well:

So it would sit on the belt like so:

Again; I am just testing out an idea here, to see if it works, if it makes the sheath too large, and of course if the idea is a good idea in practice (IRL)
Please share thoughts and other ideas with me, both on this and if you have any other (and better) ideas
Sent from my iPhone using Tapatalk
-
I can’t think of anything else on
how to store the bits in a better way
-
@Wspeed said:
I can’t think of anything else on
how to store the bits in a better way
“Nay leather” and “DeadSkins” makes custom sheaths, and they have a model that has a sheath for a bit kit too, but they are expensive....deadskin ones are like 170 day aus dollars.
And I will be frank and say I am not spending that kind of money on a sheath.
Leatherman makes a nylon sheath/ pouch thing for the bit kit too, but I am not a fan of Velcro and nylon sheaths.
My zip tie idea here was also based on costs and what I had laying around, if my Frankenstein sheath idea here turns out to be a good concept, then I might have a go at making one myself or take it to the next step somehow.
However; if it is the case that having one big sheath is a dumb idea, I will start experimenting with having 2 separate sheaths.
In the end; it’s all about finding out what works best for one self. [emoji846]
Sent from my iPhone using Tapatalk
-
One thing that has bothered me about my Rebar since I first got it, was that you can’t close both handles at the same time without them hitting each other without opening the pliers, and/or if one handle is in the closed position and the other in the open, then you have to open the pliers to close both handles.
And sometimes due to the handles hitting each other they would slam shut and pinch my hand or finger in the process.
So I had a go with the grinder to try to round them off, as pictured below.


Results are exactly what I hoped for, so now it’s a lot easier to open and close, and the handles can open and close independently from each other too, which makes it a lot easier to open and close one handedly too

Sent from my iPhone using Tapatalk
-
Nice job MMR

-
It almost makes wonder why LM designers the handles the way they did....they are so much better this way...
....that was one thing I always loved about my Kick, was how easy it is to open and close....and with that; how easy it is to use with one hand, if needed
Sent from my iPhone using Tapatalk
-
Good job MMR

Somehow that particular aspect of the Rebar handles has never bothered me, but you're right, why were they designed this way?

-
Ruler spacing?
-
@Dutch_Tooler said:
Good job MMR
Somehow that particular aspect of the Rebar handles has never bothered me, but you're right, why were they designed this way?

When I first got my Rebar, one day I was working on a lawn mower on troubleshooting what ticked all the symptoms of a bad ground connection somewhere...
...anyway, I don’t remember exactly what I was doing, but it was something where I had to hold a part with one hand and use my LM with the other, and in that process I had to close one handedly and pressing it against my leg (like I have always done with my Kick and charge without any issues), but due to the Rebars handles design I couldn’t do it and I had to leave it open and just stick it in my pocket instead of back in the sheath.
Ever since that day this design of the handles has bothered me.
And on several occasions due to this design, the handles has “snapped shut” when trying to close them in a hurry and in that process they have pinched my hand and fingers several times too..
...so it was just a matter of time before I would do something to address this.
I must say though; after having rounded them off like I did, they feel a lot more smooth and “right” to open and close now, in the same way that my charge and Kick feels...meaning; this is how they should feel.
Which makes me wonder even more why they designed them in a way where they hit each other when you open and close them, because they didn’t feel “right” before
Sent from my iPhone using Tapatalk
Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login
