What Traditional Knife are you toting today?
-
@50ft-trad said:
David, Sparky, Steve, RR,
Always good carries in this thread.Queen #63 today. Pretty sure this is a parts knife.

Parts knife?
It was built towards the end of Queens Production. It's is 1095 with Delrin handles like Queen city but not stamped Queen City.
It wasn't unusual for Queen to make special runs with extra parts. It's a blade etch I haven't seen before. I haven't found a picture of it in their catalogs, Maybe it was a SFO.Thanks Dean, I wasn’t even aware they had ceased production. When you said parts knife, my first thought was that you meant you were going to break it for parts. Assembled from leftovers was my second guess, but figured I'd better check

But... I don't speak acronym. What's SFO? :D
-
@50ft-trad said:
@50ft-trad said:
David, Sparky, Steve, RR,
Always good carries in this thread.Queen #63 today. Pretty sure this is a parts knife.

Parts knife?
It was built towards the end of Queens Production. It's is 1095 with Delrin handles like Queen city but not stamped Queen City.
It wasn't unusual for Queen to make special runs with extra parts. It's a blade etch I haven't seen before. I haven't found a picture of it in their catalogs, Maybe it was a SFO.Thanks Dean, I wasn’t even aware they had ceased production. When you said parts knife, my first thought was that you meant you were going to break it for parts. Assembled from leftovers was my second guess, but figured I'd better check

But... I don't speak acronym. What's SFO? :D
Special Factory Order
-
@50ft-trad said:
@50ft-trad said:
[quote author=Dean51 link=topic=68477.msg1783086#msg1783086 date=1538350348]
David, Sparky, Steve, RR,
Always good carries in this thread.Queen #63 today. Pretty sure this is a parts knife.

Parts knife?
It was built towards the end of Queens Production. It's is 1095 with Delrin handles like Queen city but not stamped Queen City.
It wasn't unusual for Queen to make special runs with extra parts. It's a blade etch I haven't seen before. I haven't found a picture of it in their catalogs, Maybe it was a SFO.Thanks Dean, I wasn’t even aware they had ceased production. When you said parts knife, my first thought was that you meant you were going to break it for parts. Assembled from leftovers was my second guess, but figured I'd better check

But... I don't speak acronym. What's SFO? :D
Special Factory Order
[/quote]Thank you

-
72 & 48
-
This was my second Queen, a #63 railsplitter. I thought I would carry it one last time.
:D
Something evil is going to happen to it.

-
-
This was my second Queen, a #63 railsplitter. I thought I would carry it one last time.
:D
Something evil is going to happen to it.

Is it going to lose a layer ?
Could be.
The knife weighs in at 3.6 oz I don't notice the weight but I notice the thickness, so the result is it hasn't been carried much. The other two are a full layer thinner and have been carried quite a bit.
If it comes out nice I'll post up some process pics.
If it gets totaled I'll deny I ever did it.
-
This was my second Queen, a #63 railsplitter. I thought I would carry it one last time.
:D
Something evil is going to happen to it.

Is it going to lose a layer ?
Could be.
The knife weighs in at 3.6 oz I don't notice the weight but I notice the thickness, so the result is it hasn't been carried much. The other two are a full layer thinner and have been carried quite a bit.
If it comes out nice I'll post up some process pics.
If it gets totaled I'll deny I ever did it.
That sounds interesting

So are you going to build up the other layer as a separate knife?
-
This was my second Queen, a #63 railsplitter. I thought I would carry it one last time.
:D
Something evil is going to happen to it.

Is it going to lose a layer ?
Could be.
The knife weighs in at 3.6 oz I don't notice the weight but I notice the thickness, so the result is it hasn't been carried much. The other two are a full layer thinner and have been carried quite a bit.
If it comes out nice I'll post up some process pics.
If it gets totaled I'll deny I ever did it.
That sounds interesting

So are you going to build up the other layer as a separate knife?
I'll remove the pen and sheep blade along their spring. That will leave me a single blade jack knife with a clip blade.
I'm going to try and reuse the original scales. -
[quote author=Dean51 link=topic=68477.msg1783737#msg1783737 date=1538425593]
This was my second Queen, a #63 railsplitter. I thought I would carry it one last time.:D
Something evil is going to happen to it.

Is it going to lose a layer ?
Could be.
The knife weighs in at 3.6 oz I don't notice the weight but I notice the thickness, so the result is it hasn't been carried much. The other two are a full layer thinner and have been carried quite a bit.
If it comes out nice I'll post up some process pics.
If it gets totaled I'll deny I ever did it.
That sounds interesting

So are you going to build up the other layer as a separate knife?
I'll remove the pen and sheep blade along their spring. That will leave me a single blade jack knife with a clip blade.
I'm going to try and reuse the original scales.
[/quote]

-
Great Barlow!

@gdoolittle said:
72 & 48

The 48 is a magnificent knife.
Looks likenthe 48 is getting some good use!

@Dean51 said:
This was my second Queen, a #63 railsplitter. I thought I would carry it one last time.:D
Something evil is going to happen to it.

Thats some good looking bone on that Railsplitter!

-
@Dean51 said:
I'll remove the pen and sheep blade along their spring. That will leave me a single blade jack knife with a clip blade.
I'm going to try and reuse the original scales.I thought that was what you were going to do, buddy
you should certainly have enough pin length remaining to do that after drilling one side. I just wondered what you were planning to do with the offcast layer -
I'll remove the pen and sheep blade along their spring. That will leave me a single blade jack knife with a clip blade.
I'm going to try and reuse the original scales.I thought that was what you were going to do, buddy
you should certainly have enough pin length remaining to do that after drilling one side. I just wondered what you were planning to do with the offcast layerThe offcast parts will wind up in a parts bin and forgotten about.
-
Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login





