Show me your drills
-
My drill arsenal is 95% Milwaukee , both 12 and 18 Volt , with a preference going to brushless . I have 12/18 chargers (2) , and a 3x12/3x18 gang charger . It’s hard to beat the breadth of the Milwukee line , everything from drain snakes , and pecs expanders , to saws and hammerdrills on two readily available platforms . I learned the hard way not to standardise on any system where I cant readilly replace batteries / chargers from a good industrial supply, or a big box store . Reptiles steal both batteries and chargers !
At one time I was in charger hell , Hilti , Metabo x2 , Makita , Bosch , and Milwaukee . Never again ! Now I just use Bosch 12V, and Milwaukee in the field . I do have some Festool , in my home workshop , but they are recreational , not professional .
I only have 1 corhed drill , 1 corded saw , and a corded belt sander , all else is cordless ! My jobsite lighting is all cordless , my answer to inverters , or generators , is a drywall bucket , with a re enforced bottom full of charged batteries . The infamous “Bucket O’ Batteries .
If all I did was straight up stuff , I would be tempted to go Hilti , however I do a lot of multitrade maintenance , as a side job .
Best Regards , and YMMV
Chris
-
@Grant Lamontagne said:
So far my biggest problem after 3-5 years has been finding the right batteries. The manufacturers are getting better for sure, but when I went to replace my old Craftsman drill battery it was something like 12V and no one made anything below 18V then. Then it was 21V and so on and so on.Def
Have you looked at non-OEM compatible batteries ? Or even having your existing battery packs rebuilt with new batteries. I have done both as there are numerous suppliers here in Oz and they are WAY cheaper than buying OEM.
-
Just dragged this monstrosity out of the shed. I'm putting together a "hobby desk", and figured it might be useful.
A neighbour gave it to me before he moved away, and it had been stood idle for a few years before that, so it does need a little bit of cleaning up. The foot, table, and column are quite rusty, but a little wire wool and a spot of oil should tidy it up a bit. The drive and bearings seem fine, though I don't know how much life the v belt has in it. I'll probably need to take the chuck off and inspect that too, as it's sticking a bit. Probably nothing a wire brush and dab of grease can't fix.

-
Nice !

-
@50ft-trad said:
Just dragged this monstrosity out of the shed. I'm putting together a "hobby desk", and figured it might be useful.A neighbour gave it to me before he moved away, and it had been stood idle for a few years before that, so it does need a little bit of cleaning up. The foot, table, and column are quite rusty, but a little wire wool and a spot of oil should tidy it up a bit. The drive and bearings seem fine, though I don't know how much life the v belt has in it. I'll probably need to take the chuck off and inspect that too, as it's sticking a bit. Probably nothing a wire brush and dab of grease can't fix.
Ohhh, how nice! Don’t forget pics of this little hobby desk, wonder where you got that idea

JR -
@50ft-trad said:
Just dragged this monstrosity out of the shed. I'm putting together a "hobby desk", and figured it might be useful.
A neighbour gave it to me before he moved away, and it had been stood idle for a few years before that, so it does need a little bit of cleaning up. The foot, table, and column are quite rusty, but a little wire wool and a spot of oil should tidy it up a bit. The drive and bearings seem fine, though I don't know how much life the v belt has in it. I'll probably need to take the chuck off and inspect that too, as it's sticking a bit. Probably nothing a wire brush and dab of grease can't fix.
Ohhh, how nice! Don’t forget pics of this little hobby desk, wonder where you got that idea

JRIt'll be a while before pics, as there's still a lot more sorting needed, and I can only do a bit each day. I will get them up when it's done though

-
@50ft-trad said:
@50ft-trad said:
Just dragged this monstrosity out of the shed. I'm putting together a "hobby desk", and figured it might be useful.
A neighbour gave it to me before he moved away, and it had been stood idle for a few years before that, so it does need a little bit of cleaning up. The foot, table, and column are quite rusty, but a little wire wool and a spot of oil should tidy it up a bit. The drive and bearings seem fine, though I don't know how much life the v belt has in it. I'll probably need to take the chuck off and inspect that too, as it's sticking a bit. Probably nothing a wire brush and dab of grease can't fix.
Ohhh, how nice! Don’t forget pics of this little hobby desk, wonder where you got that idea

JRIt'll be a while before pics, as there's still a lot more sorting needed, and I can only do a bit each day. I will get them up when it's done though

Oh I’m sure, but we better get a report on that 6 in 1, I’ve always thought about getting one of those but they look so cheesy, yet to have both a metal and wood lathe, along with a drillpress, a disk sander and jig all in little room would be great.
JR -
@MadPlumbarian said:
Oh I’m sure, but we better get a report on that 6 in 1, I’ve always thought about getting one of those but they look so cheesy, yet to have both a metal and wood lathe, along with a drillpress, a disk sander and jig all in little room would be great.
JR
Will do! -
I know Milwakee makes the strongest drills atm, but my experience with their batteries and customer service haven't exactly been the greatest....Makita also makes good stuff, but they are hard and expensive to find anyone who stocks around here....and when one does they are usually stupidly expensive.
My dad is a huge fan of Borsch, and he has had pretty good experiences with them. I personally don't have any bad experiences with them either.
But personally I am a DeWalt person, I am sure that there are better drills and various powertools out there, but pretty much every DIY store here in Ireland has DeWalt stuff and batteries and chargers etc. are widely available everywhere too, plus their accessories, like bit drivers, drill bits etc are pretty good too and not too expensive either.
Anyway, here's a picture of my DeWalt stuff.

-
@MMR said:
I know Milwakee makes the strongest drills atm, but my experience with their batteries and customer service haven't exactly been the greatest....Makita also makes good stuff, but they are hard and expensive to find anyone who stocks around here....and when one does they are usually stupidly expensive.My dad is a huge fan of Borsch, and he has had pretty good experiences with them. I personally don't have any bad experiences with them either.
But personally I am a DeWalt person, I am sure that there are better drills and various powertools out there, but pretty much every DIY store here in Ireland has DeWalt stuff and batteries and chargers etc. are widely available everywhere too, plus their accessories, like bit drivers, drill bits etc are pretty good too and not too expensive either.
Anyway, here's a picture of my DeWalt stuff.
I'd actually like to try DeWalt corded tools as they are seemingly unbreakable but here they are hard to find. So it is interesting to see that in Ireland they are everywhere
-
I know Milwakee makes the strongest drills atm, but my experience with their batteries and customer service haven't exactly been the greatest....Makita also makes good stuff, but they are hard and expensive to find anyone who stocks around here....and when one does they are usually stupidly expensive.
My dad is a huge fan of Borsch, and he has had pretty good experiences with them. I personally don't have any bad experiences with them either.
But personally I am a DeWalt person, I am sure that there are better drills and various powertools out there, but pretty much every DIY store here in Ireland has DeWalt stuff and batteries and chargers etc. are widely available everywhere too, plus their accessories, like bit drivers, drill bits etc are pretty good too and not too expensive either.
Anyway, here's a picture of my DeWalt stuff.
I'd actually like to try DeWalt corded tools as they are seemingly unbreakable but here they are hard to find. So it is interesting to see that in Ireland they are everywhere
I don't know if they are "unbreakable", but I haven't had any issues with anything I have had from DeWalt, all the builders and tradesman I know here in Ireland all use DeWalt stuff too, so that's usually a good sign too. Seriously, go to any building / construction site here in Ireland and you will almost with 100% certainty see all of the builders holding a tool from DeWalt.
I just want to say though that I personally don't have any experience with their corded tools, I have only had cordless tools from DeWalt.
-
Most corded tools I see builders use are either from Hilti or Einhell.
I don't have any experiences with either of those brands, the times I have seen Hilti in the stores they have usually been super expensive. Einhell seems to be more reasonable priced, usually around the same as DeWalt or Borsch
-
I've had all the major brands of cordless drills over the years and the batteries were always the weakest link. Makita, Milwaukee, Dewalt and Rigid. The batteries hold up much better these days. My latest for the last couple of years is a Bosch and I really like it. Built in LED light is really handy and it has held up well so far. I use it for work so it's seen quite a bit of use.
-
@MMR said:
Most corded tools I see builders use are either from Hilti or Einhell.I don't have any experiences with either of those brands, the times I have seen Hilti in the stores they have usually been super expensive. Einhell seems to be more reasonable priced, usually around the same as DeWalt or Borsch
I've tried Hilti tools. very fun to use
-
These are mine. Three 10.8V cordless drills (the current models are marketed as 12V but are basically identical). One of them is an impact driver. I really like these small machines, they are very light but still plenty powerful for most of the jobs. But to be honest I've been thinking about adding a couple of 18V machines.

And the corded one. My house has concrete walls and ceilings so this one is pretty useful.

-
Besides the new cordless set, I forgot I do have a simple corded, a drywall, and a very big hammer drill like Reinier’s but a dewalt out in the garage,
JR -
@Reinier said:
These are mine. Three 10.8V cordless drills (the current models are marketed as 12V but are basically identical). One of them is an impact driver. I really like these small machines, they are very light but still plenty powerful for most of the jobs. But to be honest I've been thinking about adding a couple of 18V machines.
I've had that drill and impact driver for years and almost always reaches for them over the 18v ones. They are surprisingly powerful, even drive 3 inch screws easily (although battery runs down quickly). I only go for the 18v when I need to drive more than a few, or bigger holes than a standard twist drill bit, or change my tires.
Most people would be well served by a set of 12v brushless drill/impact driver.
-
The impact driver is not powerful enough for these things though: https://www.toolstation.nl/shop/Screws+%26+Fixings/d90/Plugs/sd2040/Fischer+SXR+T+kozijnpluggen/p59898?lnjs=nl&p=59898&sd=2040&d=2040
I always need to use the corded hammer drill for those instead. Which is not really recommended. -
@Reinier said:
The impact driver is not powerful enough for these things though: https://www.toolstation.nl/shop/Screws+%26+Fixings/d90/Plugs/sd2040/Fischer+SXR+T+kozijnpluggen/p59898?lnjs=nl&p=59898&sd=2040&d=2040
I always need to use the corded hammer drill for those instead. Which is not really recommended.That's surprising to hear, the 12v impact driver should have more torque than most drills.
But the 18v brushless impact driver will be able to handle any screw you have.
-
I have and use many,many drills but this might be my favorite of all time in the end?
Milwaukee D-Handle with 30 degree extension.
It is corded but the cord is detached here and I have 25' and 50' cordsets for it.
This can drive a 4" Auger or 6' or almost any bit through wood with almost no effort at all as the torque is eaten by the extension pretty much.this hardly feels nails and rarely stops for them either.
Also I do not need a ladder to drill Joists many times or to hit my knees for plates or horizontal runs.Overall just an amazing drill.
The Stud Buster!

Sent from my iPhone using Tapatalk
Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login