Let's see some Kershaw's!
-
:o

-
Very nice, Spartan!

I didn't know Kershaw made the Leek in that finish. :) -
-

I see your Leek,
and raise my Oh-So Sweet!

@gerleatherberman said:
Very nice, Spartan!
I didn't know Kershaw made the Leek in that finish. :)Thanks guys! I saw that cammo finish, and couldn't resist
-
Onion Sweet tortilla, Oso Sweet knife :D

-
I'm a bit disgusted with my Skyline......

Firstly, 14C28N.......great steel, more than good enough compared to 8cr13
My main problem is deployment, it's just not a good flipper, especially not after few months pocket time, and what gets me it's not even obviously dirty....
Currently it's easier to use the horribly sharp blade stops like thumbstuds, but that's less than ideal.
Yesterday I tried to cut a dead branch off an office plant, wood was a bit harder than expected so I couldn't get through......went to close the knife and found the liner lock at past 100%

Thought about it and that alone is not a deal breaker......with the single liner a bit of flex is to be expected.
-
@Gerhard Gerber said:
I'm a bit disgusted with my Skyline......
Firstly, 14C28N.......great steel, more than good enough compared to 8cr13
My main problem is deployment, it's just not a good flipper, especially not after few months pocket time, and what gets me it's not even obviously dirty....
Currently it's easier to use the horribly sharp blade stops like thumbstuds, but that's less than ideal.
Yesterday I tried to cut a dead branch off an office plant, wood was a bit harder than expected so I couldn't get through......went to close the knife and found the liner lock at past 100%

Thought about it and that alone is not a deal breaker......with the single liner a bit of flex is to be expected.
Maybe try one of the models with bearings if you cant carry an assited, heard good things about the atmos
-
@Blackbeard said:
Maybe try one of the models with bearings if you cant carry an assited, heard good things about the atmosI don't think that's the answer, I've seen what pocket lint does bearing pivots

The blade is great, thin and slicey....all good.
Put that blade in a Spyderco Salt 1 chassis and you've got a hassle-free pocket knife.
If my Salt 1 was PE and the hole was smaller thus lowering the profile of the knife, it would be no contest.....
-
TX tool - Any good?
-
Kershaw Emerson cqc-5

Sent fra min FRD-L09 via Tapatalk
-
Kershaw Skyline Plan of action
- grind off flipper
- give blade stops few passes under the polisher
- slightly hollow out G10 to give easier access to use the blade stops as thumb studs.
-
-
My mind has changed a bit.......
Skyline, and
14C28NI cringed watching how the knife was used yesterday, and I was waiting for the blade to chip out......heard it scratch against the old bushings so many times......
Rinsed it off last night, and 1 drop of Daiwa reel oil on the pivot and it was deploying perfectly again........
What I'm reconsidering is removing the flipper tab, not for deployment reasons but for the guard it forms......that was quite useful yesterday....
Now the steel.....
The edge had a few flat spots, I suspect from in-pocket meetings with me keys. By last night it was just dull.
I touched up the edge with a diamond sharpener 3-beer free-hand steady, stropped it and it slices receipt paper

-
Did the full Nick on my Skyline, and while I had it apart put a 17 degree edge on it with the Lansky

I think the term is "sticky sharp"
Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login




.jpg)


