Show off your Sak mod's!
-
Lastly a jet setter plus pen mod to be school/plane friendly on the keychain.

-
How fast can you say MODDING SPREE?
Very nice.

-
Nice mods Andrew Rueger!

Sent from my Redmi Note 5
-
Nice mods Andrew

-
Finally worked up the courage to pull apart my favourite Victorinox. A red Alox Cadet that I have carried on and off for the past 5-6 years, always wishing it had scissors. I think I have also finally got the Wenger in 84mm Alox mod, to get consistent snap and closure of the scissors I had to reshape the spring out of a Recruit as used in the tutorial on the board. I made a ramp out of the leading edge of the tool rear and all is well. I am truly happy to have a RED, as Macgyver would have had it, Alox 84mm Small Tinker X. The hardest part of this mod was working up the courage to make the first cut in the scale for the Phillips, knowing there was no going back.


-
That mod is great!
8) -
Awlsome work,!
[It's not failure if you learn something from it]
-
Couple of questions @Andrew
Does the Cadet have four pins like a 91mm? As normally it has no backtools - right?
What spring did you use for the Phillips? As presumably this was not from a Cadet?Looks great
-
@Huntsman said:
Couple of questions @AndrewDoes the Cadet have four pins like a 91mm? As normally it has no backtools - right?
What spring did you use for the Phillips? As presumably this was not from a Cadet?Looks great
the cadet is built from the factory with 3 pins more similar to the 93mm models. To make this mod work there is a "floating" 4th pin that is counter sunk about 1mm or into the alox scales on either side, I also added the scale liner from the Small Tinker to add thickness to the scale with the phillips, you don't have to do this but the phillips will protrude out past the scale by a fair bit, it still isn't perfectly flush with the scale as built but it isn't annoying. This 4th pin holds in the springs with backside tools from sliding back and forth. I did it this way as I didn't want the 4th pin exposed as it would come out in the middle of the shield.
For the springs used the blade spring from a donor Small Tinker, again for the opener layer spring came from the Small Tinker. The spring for the scissors is a blade or opener layer spring (I cant remember) from an old style Recruit, no funny bumps and notches like the newer versions. The phillips rides the back side of the blade spring, and the awl is on the opener layer as they would be in a Small Tinker.
This all would be better with pictures I am sure, once I get started on projects I tend to get lost in them and never take pictures of what I am doing.
-
I don't know who did the work on this mod, but I like the looks of it. It is inbound to me.

-
@ Andrew - Thanks for the extra info - Much appreciated - As is often the case - Lots of work going on behind the scenes!!
@ Dutchy - Depends what you started with !! ;) Was it a PX? - I can see scissors - I think.
And of course pliers - Cant see what is opposite the mag glass - A Phillips? -
Yup, I see a Philips.

-
Completed the rebuild of these 4 little guys with screws instead of brass/nickel pivots.





Sent from my Redmi Note 5
-
Very nice! You've been busy!

Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login

