Modding a SAK 111
-
Victorinox are obviously putting a lot more thought into the design of the liners than I thought. But the fact that the first thing that I had to do on disassembly is hammer one of them flat shows that they are not always right.
Then it struck me. I had a look at a 91mm knife; specifically the pivot area. In most places the liners overhang the tool pivots by about 1.5mm. The biggest was 2mm; a few of them were actually flush. On my 111mm a 6mm overhang is normal. I guess it gives extra support when the tools are open but on the other hand it's not surprising that I'm managing to bend the thinner liners.
To be honest it's not really a big problem; the knife has lived in my pocket daily for ten years with minimal damage. But, on the whole I'd have gone for the thicker liners throughout and accepted the tiny weight penalty.
(By the way, if you look really hard at the bottom of the black 111mm, you can still see a small gap between the liner and the scale where I did not quite get it flat. I'll tweak it slightly with pliers when I put new scales on it.)
-
Eeeeeew, that 91mm needs a clean when you look at it close, doesn't it?

-
So say you had an Outrider, could you add the plier's AND move the other end tools around or whatever to also add in the mag lens?
-
Well I'm far from being an expert, but I'll have a go at answering.
If you have access to the parts of the layer containing the pliers then I don't see why you couldn't add them to the Outrider. If you don't then you'd need to buy a parts donor. The cheapest would be a Hercules, so why not just carry that?
The magnifying glass is interesting as I'd thought about it as it's the one tool that I really miss from my 91mm. This is the grey plastic magnifier. I really didn't want to strip it from my 91mm, but if I did I'd be struggling to find a spot to put it in on the 111mm. The layer that the magnifier is on is a thick one at 2.7mm so I don't think that it would be happy on the bottle/can opener layer. The closest in thickness is the scissor layer; I'd need to lose the scissors and maybe the philips too as I don't know if the glass would sit with the screwdriver. It definitely wouldn't nestle with the scissors.
I don't know how happy you'd be to lose the scissors; I wouldn't as it's probably the tool that I use the most.
-
Actually it's just occurred to me that the Wenger magnifier is steel and may be slimmer. I'd like to have a go at mounting that, but not enough to buy one of the models that have them to strip it out for parts. They aren't the cheap models ::)
-
I'm in a moral dilemma now.
I remembered that my father in law had a swiss army knife; I had a look and blow me if it wasn't a Wenger with the steel magnifier.
It looks like it's 2.5mm thick so would swap in to a saw or file layer quite nicely, assuming the pivots are compatible.
Now, it's not strictly my knife; I guess that it's strictly my wife's.
My wife's away for the weekend; I could take the layer out when she's away and she'd never know. But women are funny and sentimental about these things. Life's hard when you have no moral compass. >:D
-
NO!
:DBetter to try making the Vic magnifier thinner (not sure if possible) or getting another Wenger.
-
Definitely don’t chop the Wenger, just get one off of the bay and save yourself the lonely nights on the sofa. As far as more ideas on your build, if you use a liner lock model than there are no underside tools on the blade layer and the corkscrew is on the saw layer. You can remove the blade layer and include the other tools from the other build. If you keep the newer bottle opener you may be able to lose your pribar too. The downside is they used different pivot sizes, so the old tools may have to be drilled out. But you would have scales that don’t rattle.
-
@Simyo said:
Definitely don’t chop the Wenger, just get one off of the bay and save yourself the lonely nights on the sofa. As far as more ideas on your build, if you use a liner lock model than there are no underside tools on the blade layer and the corkscrew is on the saw layer. You can remove the blade layer and include the other tools from the other build. If you keep the newer bottle opener you may be able to lose your pribar too. The downside is they used different pivot sizes, so the old tools may have to be drilled out. But you would have scales that don’t rattle.Just noticed this reply. The problem is, being in the UK, ebay refuse to sell knives because of bad publicity from a consumer affairs TV program. So getting cheap raw materials means visiting car boot sales or junk shops. But you are probably right; I'll keep my eye open for a cheap Wenger.
Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login

