SAK Evolution: Soldier and Officer Knives
-
Interesting, thanks.
-
Thanks Ulli, nicely done

-
There's a little typo in the title…
Edit: And it's edited.

-
Did you make this Ulli ? ???
It's great - Thanks -
- Like you say, More accurate than some others that are around.
Eg the rivets going inside in 57 not 61I must check against the Wiki and** this dating spreadsheet**
One small point -
Last entry on the Officers side - 73 was when the clip point was replaced by the drop point - Not when it appeared - Right? - ??? -
Smurf!!
That confirms my Officer's to be from before 1902!! :ahhh :ahhh :ahhh
It has the Elsener stamp on the driver :ahhh
-
Thank you sooo much...
-
@Mechanickal said:
Smurf!!That confirms my Officer's to be from before 1902!! :ahhh :ahhh :ahhh
It has the Elsener stamp on the driver :ahhh
Do you have a close foto of the stamp? Is it just "elsener", or "gesetzlich geschützt" or "armee suisse"?
They used "gesetzlich geschützt" from the beginning untill the patent expired, like they did with the "+pat" stamp.
-
Give me a few minutes...
-
ELSENER
SCHWYZ

-
Thank you ulli! I had wondered in this thread I started if there should be a distinction between #5 and #6 of the Officer's knife.

/post/1415482 -
Nice

-
Added to the main SAK identification thread:
/post/1630522
Thanks Ulli
-
This is very interesting Ulli. Many thanks for doing it!

I am puzzled by a few things in the current version.
-
If Victorinox really moved to three visible rivets in 1909, then how do we explain the existence of stainless steel SAKs with four visible rivets? Such a SAK can be seen in the following image:
The image is from this post by JAZZBASS, where he suggests that the change to three visible rivets occurred a bit later. -
I think that early stainless steel Victorinox offiziermessers from around 1923 had the older screw driver without a cap-lifter. In fact, I tend to believe that Victorinox introduced the cap-lifter only in the 1930's (probably mid-1930's). This is because stainless steel SAKs with the older screw driver seem to be relatively common and to make up the vast majority of the SAKs with a slanted JNOXYD tang stamp (j2 stamp in your table). Moreover, this is also suggested in this post by JAZZBASS as well as by some other sources.
-
The change to a 4-loop corkscrew took place around 1973-74.
-
There seems to be a problem with the years assigned to the last two model 1961 alox knives. If I remember correctly, the introduction of the red shield took place in 1977 or 1978, the WK stamp was removed in 1988 or 1989 and the hollow rivet was removed around 1993.
-
-
@MiniChamp said:
This is very interesting Ulli. Many thanks for doing it!

I am puzzled by a few things in the current version.
-
If Victorinox really moved to three visible rivets in 1909, then how do we explain the existence of stainless steel SAKs with four visible rivets? Such a SAK can be seen in the following image:
The image is from this post by JAZZBASS, where he suggests that the change to three visible rivets occurred a bit later. -
I think that early stainless steel Victorinox offiziermessers from around 1923 had the older screw driver without a cap-lifter. In fact, I tend to believe that Victorinox introduced the cap-lifter only in the 1930's (probably mid-1930's). This is because stainless steel SAKs with the older screw driver seem to be relatively common and to make up the vast majority of the SAKs with a slanted JNOXYD tang stamp (j2 stamp in your table). Moreover, this is also suggested in this post by JAZZBASS as well as by some other sources.
) The change to a 4-loop corkscrew took place around 1973-74. -
There seems to be a problem with the years assigned to the last two model 1961 alox knives. If I remember correctly, the introduction of the red shield took place in 1977 or 1978, the WK stamp was removed in 1988 or 1989 and the hollow rivet was removed around 1993.

-
-
Nice idea Ulli! It definitely should be done.
I'm agree with MiniChamp we need more evidences for bottle opener dating, here's probably 1931 knife:

One more with jnoxyd stamp (late 1920s ?):


It looks like they introduced shield on soldiers in 1977:


And of course 4 turns corckscrew started c.1973.
What about soldiers, first mod.1961 Soldier knives by Victorinox has 62 on the blade (Wenger has 63).
Maybe need to add Grilon version by Wenger (1957-1964) too?Sent from my iPad using Tapatalk
-
Whow, I
m happy about that many replies. I will change the system when Im at home and check my references. I will change the title too to "spartan evolution". Its not ab out wenger and not about other models than the spartan. -
Great work, ulli, even if it's open to revision.

Some model names have changed over the years. I believe that when names were introduced, the Spartan was called the Camper. How about Victorinox returning its name to Officer's Knife to reflect its lineage and give it the distinction it deserves?

-
We all like bails. They made knives with bail till 1968

Sent from my iPad using Tapatalk
Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login

