If you want something done right....
-
From memory, I don't think they will work, but aren't there separate heads available for some Gerber models?
-
-
Good luck Bob

-
-
Have you seen the quality of Bob's work? It's worth the wait! :)
-
Is this going to be a "fixed" cutter head?
I can't see how the dia. cutter head will be able to turn inside out. :o
-
@Swiss Man said:
Is this going to be a "fixed" cutter head?I can't see how the dia. cutter head will be able to turn inside out. :o
The SOG pliers never actually go inside out. They reach maximum opening when the handles are 180 degrees opposite each other, then begin to close down again.
But still, any cutter head used must be able to open as far as the SOG plier jaws do. :-\
-
go for it bob!
I bought the saber tooth tools
the cutter head is really thick. it will fit but there won't be room for the longer impliments like the knife. another problem is that although the head is thick the part with the holes for the screws is thinner than the sog so you will need some large spacers if you want to put it on a sog. I haven't looked at the size of the hole yet to determine if the sog screws will fit adequetly. -
@scrappy said:
go for it bob!
I bought the saber tooth tools
the cutter head is really thick. it will fit but there won't be room for the longer impliments like the knife. another problem is that although the head is thick the part with the holes for the screws is thinner than the sog so you will need some large spacers if you want to put it on a sog. I haven't looked at the size of the hole yet to determine if the sog screws will fit adequetly.But it looks do-able eh? Great, I'll go ahead and order the Sabertooth tool.

-
I hadn't read your thread until now. I am not sure the plier opens wide as a sog. it is just wider than the charge. also the tool is to thick for the gears. I will try. if it doesn't work than a super bear jaws probably will.
-
@scrappy said:
I hadn't read your thread until now. I am not sure the plier opens wide as a sog. it is just wider than the charge. also the tool is to thick for the gears. I will try. if it doesn't work than a super bear jaws probably will.Any chance you could post a picture? Maybe a side-on comparison of the cutter head alongside a SOG PowerLock?
-
I have tried three tools so far.
the ppp gears are smaller so they do not get in the way. you could put the cutter on it but it won't fit in th handles. the only mod it needs is the metal around the hole for the screws is wider than the metal around the holes on the ppp.so some of it will need to be filed off. I might do that. it is okay with me if I can't fold it.
the power plier fits fine with washers if it wasn't for the gears. on the pp the gears are larger and longer than the ppp and by the time you get to the end of the longer gears the cutter is too thick to fit between the gears.
I am on my phone and will post pics tomorrow from a computer. -
@scrappy said:
I have tried three tools so far.
the ppp gears are smaller so they do not get in the way. you could put the cutter on it but it won't fit in th handles. the only mod it needs is the metal around the hole for the screws is wider than the metal around the holes on the ppp.so some of it will need to be filed off. I might do that. it is okay with me if I can't fold it.
the power plier fits fine with washers if it wasn't for the gears. on the pp the gears are larger and longer than the ppp and by the time you get to the end of the longer gears the cutter is too thick to fit between the gears.
I am on my phone and will post pics tomorrow from a computer.Great! Looking forward to seeing them sir

-
pics
-
pics
-
Hoo-boy, those really are fat aren't they? :-\
I'd want the tool to fold up, so that means the entire thickness of the Saber Tooth cutter head would need to be ground down. :( I wonder if the pivot would fall apart then?
-
actually it would fit if you remove the longer impliments. sorry about the spelling. you will need to grind below the pivot or remove the gears. the handle is fine but the gears will get in the way
-
Sounds like piece of cake for bob the great machinist, no? We'll be expecting the finished product in two weeks. :D
Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login

:D :D