Camillus Cutlery Memories
-
I've seen this before and would agree that it is indeed a very sad story. I have many Camillus knives as well as their many offshoots(which number about a hundred)made around the world. Used to go by the town(but sadly never stopped)on my way east to Massachusetts from Michigan.My relatives lived in Jamestown and virtually all the major knife manufacturers were located right off route 17(which I believe is now Interstate 86).
One of my favorite knives is a 3 line Camillus easy open jack with ebony handles that I bought in an antique shop in Ashtabula Ohio. It pre-dates WWI and was never sharpened. I opted to leave it as found and wondered what stories it might tell if it had the ability to talk.
-
-
. I wish they could talk! -
Nice old knife Ray !
-
@Barry Rowland said:
. I wish they could talk!Well... depending on how discreet they can be.
-
@SteveC said:
This is good read on the history of the companyhttp://www.collectors-of-camillus.us/History/Camillus History.pdf
and cool website
Thanks again.
-
Here is the website that I meant to post
-
The more I read the more its a bummer they didn't make it to today. Shame the building burned too. I did like how the one guy continues on making knives. Kinda funny how knives are still being sent to the old factory for warranty work.
-
@Aloha007 said:
The more I read the more its a bummer they didn't make it to today. Shame the building burned too. I did like how the one guy continues on making knives. **Kinda funny how knives are still being sent to the old factory for warranty work. **My guess is outside of hard core knife people very few folks who are still carrying a Camillus knife know the Company finally went under in 07.
-
I actually have the orange paratrooper switch blade knife. I thought I had moved it on. Neat knife btw.
-
**My 'first knife' was an 'official' Cub Scout [late-50's issue] with blue scales, and a Wolf Den emblem on it. It was either a four-blade: Camillus, or Imperial make. Looked similar to the 1970's one below. I remember the 'press lock' tabs on it. You had to earn your "Totin' Chip" card in order to carry-it. **


-
@Aloha007 said:
The more I read the more its a bummer they didn't make it to today. Shame the building burned too. I did like how the one guy continues on making knives. **Kinda funny how knives are still being sent to the old factory for warranty work. **
My guess is outside of hard core knife people very few folks who are still carrying a Camillus knife know the Company finally went under in 07.
I didn't start looking online for knives until 2009 or there about. I found out Camillus was out of business by asking the local CoOp why they didn't have Camillus any more. Kind of the same with Schrade/Old Timer. Before that I knew Camillus was getting hard to find but didn't realize they were close to closing their doors.
-
-
It's hard, if not impossible to look back at a company 20 plus years after their doors closed and judge their products. Their stock has been sold out, the New Old Stock you see on ebay may well be a retailer's left overs, snatched up during a going out of business sale. You never know what's happened to a used knife even if it looks virtually unused. I read all the time about someone complaining about or sending a knife back because the spring was .003 high or low at half stop. Or it was a tiny bit off center. Those are standards that never existed before. Really what difference does it make if a spring is a tiny bit high at half stop, you don't use a blade at half stop. Knife knuts are becoming a very picky lot.
You have to look back to 1980 to understand why companies went under. Labor costs were on the rise and the modern knife was born, Spyderco, Benchmade etc. were coming out with modern knives with new steels at a low price. Cheap Japanese imports and clones were flooding the market.
The old companies didn't have engineers they had craftsmen that were unable to adapt to the newer designs. There were attempts at modern designs but they failed to understand the new market. Labor costs were rising yet the unions fought to stop new modern manufacturing techniques that would have lowered cost and improved quality. Because it would have meant a temporary loss of employees (aka union dues). Those old family owned companies were also suffering from bad management, that was unwilling or unable to make the needed changes.
Buck streamlined and branched out to modern knives. Case streamlined production and survived, by turning 80% of their production to candy colored novelty knives and collectibles. Now the flood of cheap RR's is forcing has Case to experiment with a line of Chinese made moderns.
In short times changed and the old companies didn't.
-
-
-
It's sad to see the factories close. To see what they once we're and now what's left. Car factories in Detroit. The steel and railroads of my own home state left to rot and fall apart. I'd love to be able to re open the old plants and start making old timers and camillus in the states again
-
Dean51

@Spartan. It would be great to have bought up all the Camillus stuff and relaunch them. Its unfortunate how fickle the knife community is. Its darned if you do and darned if you don't. GEC might have it right? Case is slugging it out it seems and good for them.
-
@Spartan. It would be great to have bought up all the Camillus stuff and relaunch them. Its unfortunate how fickle the knife community is. Its darned if you do and darned if you don't. GEC might have it right? Case is slugging it out it seems and good for them.
I hear that aloha! I didn't know that case was bringing in Chinese knives for their lineup. Does anyone know which ones they are?
-
I think pretty much every cutlery manufacturer still extant in the US has imported lines and or parts. Gerber and SOG, I think are largely imported. Utica, at least what I find in stores here, has a lot of imported lines. Bear and Sons has the Bear Edge line, which is imported. Case has Tec-X. Even Camillus and Schrade, as the original companies, had multiple imported lines.
But, personally, I am not really impressed by what Taylor Brands (now owned by Smith and Wesson, I think) and Acme are doing with the Camillus and Schrade names. The quality seems to scream "bargain bin special" and they all use mediocre steel. Yet, my Rough Riders are half the cost of a Chinese Schrade or Camillus, but 100X better. And it doesn't help that Taylor are taking over the mom and pop hardware store cutlery displays. Our Farm Bureau replaced Case (they were a silver level dealer) with Taylor Schrade. At the very least, they could allow Bear and Sons, Utica, or even GEC to produce some knives in the USA. There were some GEC Schrades, I might add, in 2005-6 based on the Oregon Trapper; done as a special edition. Now, an Oregon Trapper, in Old Timer trim with sawcut bone would look awesome!
In terms of modern designs, I love my Schrade Tough Tool, Cliphangers, and am trading at present for a Lake and Walker. Camillus had great stainless steel, and a ton of modern designs. The LEV-R-LOK was especially cool, and I find the Sierra to be a great workhorse.
Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login