kamakiri's Former Lurker / New Member Intro (long read)
-

woodsman sounds great! -
January Challenge is over...back to work:





Liners were too dirty and oxidized to leave alone. Re-brushed them all before polishing all the visible surfaces and edges.
Gonna go through all the tools too, so assembly might not happen until next week. Only tool done was the Metal Saw and that's not going to get extra polish.
-
Great mod the reverse kamakiri style yeoman thingy

I was wondering, does the combo tool get in contact with the scissors?
And do you think the mag/philips layer could be better put into the middle position?Excellent thread btw

Looking forward to the next one

-
Looking good

-
@MTMatt said:
Great mod the reverse kamakiri style yeoman thingy
I was wondering, does the combo tool get in contact with the scissors?
And do you think the mag/philips layer could be better put into the middle position?Excellent thread btw

Looking forward to the next one

Thanks, MTMatt!There's zero contact for the combo and scissor. The combo tool does sit into the liner space, but have to push pretty hard to make them touch. I thought about the mag layer in the middle like the Swiss Bianco? (not sure on that), but I think the older/longer Phillips would make contact with the combo where the newer short style wouldn't (I suppose). If I recall correctly, the original Yeoman had the same liner contact issue. I figured I could live with it.
Not sure if I mentioned it earlier, the main reason for the reverse is to have the short side spring and higher compression to resist movement better when using it as a pry tool. I'd say the force to close is nearly double from the normal position. I know most would not like the small blade, but I wanted this to be proof of concept to put a Pruner blade instead.
This one is 'nothing special' technically speaking. I've got some other more interesting stuff lined up for 'proofing'.

Thank you Sir W!
I hope this one isn't too boring!
I also gotta get back to some of the content I intended for the original post. :ahhh But new mods are more fun.

-More of the story for my '84.5 Champion
-The bee story
- Marlboro stuff and mods
-Champions
-Early naming conventions (Particularly Craftsman and 136xxx relatives)
-More Hoffritz and Timeline data
-Ranger Production Timeline
-Camping Inlay Timeline
-Vintage Catalog version dating.
And I'm probably forgetting something at the moment. ::)

-
Beautiful work with the Yeoman!

I'd just call it Yeokiri and be done with it! ::) :D
-
@AlephZero said:
Beautiful work with the Yeoman!
I'd just call it Yeokiri and be done with it! ::) :D
Thanks, AlephZero! I'm just not that clever! 
-
This is definitely not boring kamakiri keep up the good work

-
Most welcome!

-
Very entertaining

-
<u>Project: 'Troublemaker'</u>
Had some time to finish my Troubleshooter Lite + Pen. Waffled a bit about adding a Wood Saw and using the Corkscrew instead for this temporary/test build and making it a Handyman Lite Plus, but it would add time to get the Saw from the fodder box. And adding another Layer would make it close to Champ size. This way it would still be about a half layer thinner than a Champ and about a full layer thinner than a CT Lite but have at least 1 saw. Intent is to have a Magnifier in place of the In-line Phillips for the 'final' build.
Misc polishing:

Don't need this:

'free' pins during assembly:

Layer 1 Openers/Awl:

Layer2 Lite (would add magnifier here on permanent build instead of phillips):


Layer 3 Pliers (FYI - If I put the scissor here it could save a 1mm spacer):

Layer 4 Scissor/Hook:

Layer 5 Saw/Chisel:

Layer 6 Blades and back Phillips:

Top view:

Measure and trim pins:

Hammer Time:





Pressed on original/modified for pen scales:




@CallsignBadger said:
Very entertaining

Thanks, CsB...I hope this one was, even if a little. Was glad for the knife time today and to finish this one. 
-

Nice one

-
Thanks again CsB!
Troublemaker living up to its name...showing off new hardware to it's sibling and Hoffritz cousin:

-
Nice peening, excellent work Kamakiri 
-
Excellent work kamakiri

-
Nice limited edition

-
@MTMatt said:
Nice peening, excellent work Kamakiri 
Thanks, MTMatt! Better looking than when I clip-n-hammer for temporary builds using the damaged bushings!Thanks, Wspeed! I always put more effort with builds that may be permanent. And get even pickier with restorations. I left one of the pins about 0.12 mm longer than I wanted and would have taken it off for a restoration, but okay for a user like this.
Thanks, CsB! I hope there's still entertainment value in there!

I thought you might notice that, Ray!
;)
Gotta quickly figure out what I'm going to do with knife time this afternoon...might just be cleaning some of the recent arrivals.

-
@MTMatt said:
Nice peening, excellent work Kamakiri 
Thanks, MTMatt! Better looking than when I clip-n-hammer for temporary builds using the damaged bushings!Thanks, Wspeed! I always put more effort with builds that may be permanent. And get even pickier with restorations. I left one of the pins about 0.12 mm longer than I wanted and would have taken it off for a restoration, but okay for a user like this.
Thanks, CsB! I hope there's still entertainment value in there!

I thought you might notice that, Ray!
;)
Gotta quickly figure out what I'm going to do with knife time this afternoon...might just be cleaning some of the recent arrivals.

Oh yeah, I saw!

Glad you got it!

-
I said I buy crap...sometimes it's not intentional.
Small blade in the listing only mentioned 'light scratches' and said nothing about the very pronounced BENT TIP ::)
Mother Hamster Smurf it ALL:

a bit better:

Still too visible from the blade side:

Good enough to leave for now. At least it sits nowhere near the main blade now.

Rest of the knife and the edge on this blade was great so I didn't want to bother with a return or refund or pulling it apart to replace the blade. I have enough of those to do that I knew about when purchasing. ::)
Just glad I didn't have any errant blows and ruin the factory edge. Still cuts nicely and separates news print just fine.
Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login