February Fixie Challenge
-
Nix’s Sheath Tutorial — Part Two
So, now you've gotten leather and rivets and a knife all pulled together. At this point, you need to come up with a design.
The design should be fairly precise, but don't sweat it too much. Leather is a forgiving material, and we can resort to some 'cheats' if we need to. However, the better our design and layout is, the easier the whole process will be.
My sheath will be symmetrical. This is somewhat conventional, but, really, arbitrary. Since the sheath will be symmetrical, I folded my cardboard in half to establish a center line. Then I laid the knife next to the center-line. I learned to lay the knife's spine on the center line, but this resulted in too tight a sheath, especially for thick-handled knives. Now I set the knife just a bit over the center line. Then the knife is carefully rotated over to it's side. Then the knife's silhouette is traced out.
At this point, I can start planning where I want the top edge of the sheath to come up the knife. The bottom inside edge is defined by the very tip of the knife. The bottom exterior edge gives me space for the welt and a bit of a margin for stitching. In general, it's nice to have 1/4" of leather welt protecting the stitching from the edge and 1/4" from the edge of the sheath to the stitching line.
In this case, I've used a penny in place of a ruler to mark out the margin between inside bottom and outside bottom edges. (I normally use a pencil so I can change my design, but it didn't show up well in a photo, so I'm using a marker instead. grrrr.....)

Pretty simple, right?
Let's talk about the 'welt' for a moment.
A welt is a strip of material (leather in this case) that acts as a spacer, but, more importantly, protects the stitching from the knife's edge. You MUST have a welt. Otherwise the knife will cut open the stitching, fall out of the sheath, and stab you in the leg. While your friends will think this is hysterical, it'll bring your hike or trip to an early end.
The strip of leather below this sheath has been cut to form a welt:

OK. So now that I've got the basic size and shape of the knife mapped out, I can begin to think of extra design features.
What shape do I want the sheath?
I think I'll go with a rectangular shape for this one. No reason, really, but a rectangle is fairly nondescript and non-threatening. Plus it will let me add some extra stitching and a tie-down hole.
What kind of belt loop do I want?
I often sew in a belt loop as a separate unit, 1/4 of the way down the sheath. For this one, however, let's go with a 'fold-over' belt loop. A fold-over doesn't snug up quite as well, but it does sit a little lower, which is convenient with a pack.
Now that I have that in mind, I can use my penny to give me an even spacing for my welt.

In the above photo, I've added the back edge of the sheath, using my penny to space out the edge from the guard (the widest point). Since this is the widest point, the sheath has to be wide enough, all the way to this point for the knife to be able to slip into the sheath. Since I'm going for a rectangular sheath, I just dropped the back edge line straight down from here.
I've used the top of the penny (halfway across my welt distance) to mark out a stitching line. This isn't necessary, but it helps me to visualize how I'm going to stitch the sheath together later.
I now have my basic design layout. I used the cardboard layout with my knife to test out how it will work. I may have made it a bit big, but I think it will work out. Time to cut out my template.....

One of the problems with a fold-over belt loop, is that it makes for an irregularly shaped piece of leather to cut out and I always feel I'm creating more scrap than necessary. But this looks like it'll work. I allow 2" of length for a 1.5" wide belt (just works out better) and then an inch of length for stitching the end of the belt loop down. In this case I added a little extra so I can have the top of the loop end up a bit higher than the top edge of the sheath. This is for a right handed sheath. A lefty could just flip the template over to get a LH carry sheath (I did that by accident once and now have a LH carry knife.)
We'll see how that awl works out.....
-
Excellent tutorial Nix, tool wise i'm good to go i think, i only have a couple of feet of thread though, hopefully that should be enough

Day 9, back to the Buck

-
Gorgeous!

-
Part three of the sheath tutorial will have to wait for tomorrow......

-
@Borg said:
Excellent tutorial Nix, tool wise i'm good to go i think, i only have a couple of feet of thread though, hopefully that should be enough
I will say, Borg, et al, you will need a lot of thread. Sheaths seem to suck up thread like a sponge sucks up water.
For the sheath I'm making now, I'll need a minimum of 2 meters of thread. I'll probably use a 2.5 meter piece. :o
Edit: I bet you could use waxed dental floss for sewing thread. Pretty good stuff.
-

Hey, Anka! I gotta agree with you. I find myself thinking about that 101 now.....

-
Thanks Nix, thanks Anka

I measured and have 1 meter of thread which is all i got with the kit, looks like i will have to make it do, i will make a shorter sheath and i don't plan to have a belt loop on it so hopefully that will save some

-
Ray, and everyone interested, there will be a few more tools making an appearance. I encourage you to wait for the complete tutorial before selecting new tools.

The tools I've shown so far are sufficient, but a few others might prove to be really useful.

-
Ok, will do. Thanks

-
Day 9
So I plan on hiking and camping more this year and I am getting all of my gear ready. I wanted to try out this cook set to see how it would work. The green carrier was purchased at a local surplus store and is just big enough to hold the cook set and some other items as you can see. I was blessed to have two LM Supertool 200s and I keep one on the pack.
My biggest issue was the handle of the pot, it was a pain getting out of the pouch. I wanted to remove it and keep it separate but it was not easily removed so I had to cut one of the ends to allow it to be removed. The file from the ST smoothed the edges. Now the pot comes out easily.
Tonight's menu was some Campbells soup which turned out to be pretty good. In my haste to eat, I forgot to time the length of cooking but it was not longer than a couple of minutes.
Overall, I am happy with the setup and I think it will be great. The MOLLE straps will allow the pouch to attach to the exterior of my main pack.
Now for the picks.









Ken
Sent from my iPad using Tapatalk
-
Day10:
Looking through my leather scraps as I thought I might do one for the Green River along with Nix’s great sheath tutorial. Not enough, and I see it already started while I was sleeping.
-
Nix, I'm greatly enjoying the tutorial so far! Keep it coming!

KBM3, nice cooking setup you got there!

Great photos and uses overall guys!

Sent from my Redmi Note 5
-
Day 10
We often make pork pies for school lunches in the coming week. We use Paul Hollywood’s recipe which is dead easy to follow and gives consistently good results. Everything from scratch (well not quite catching the pig and grinding the flour). Rope my 11 year-old in for the flour mixing and pastry work. The Smith knife worked great for chopping the pork and bacon, but the high-carbon steel does not like onion and immediately tarnished. Fixed later with a little oil and fine steel wool. The pies are now cooling, waiting for their gelatin that goes in the top.




-
...last few pics





-

Those pork pies look great!

(yeah, onion will tarnish carbon steel quickly. But I like that patina.....)
-
Nice pack bag, Ken. I like your mod. Is the handle secure when the pot is full?
(knife is looking great, too.)
-
So I plan on hiking and camping more this year and I am getting all of my gear ready. I wanted to try out this cook set to see how it would work. The green carrier was purchased at a local surplus store and is just big enough to hold the cook set and some other items as you can see. I was blessed to have two LM Supertool 200s and I keep one on the pack.
My biggest issue was the handle of the pot, it was a pain getting out of the pouch. I wanted to remove it and keep it separate but it was not easily removed so I had to cut one of the ends to allow it to be removed. The file from the ST smoothed the edges. Now the pot comes out easily.
Tonight's menu was some Campbells soup which turned out to be pretty good. In my haste to eat, I forgot to time the length of cooking but it was not longer than a couple of minutes.
Overall, I am happy with the setup and I think it will be great. The MOLLE straps will allow the pouch to attach to the exterior of my main pack.
Now for the picks.









Ken
Sent from my iPad using Tapatalk
That is a nice little set up.

Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login

