February Fixie Challenge
-
(Oooops, I lost track of my numbers. I entered Day 05 two days in a row and fell behind in my sequence. Back on track with Day 10, today. :-)
Making Welsh Rarebit (always called Welsh Rabbit here) for lunch. Recipe calls for 1/2 cup of dark beer.

Dutch_Tooler can feel well assured that the cap lifter on the Ulu works very well!

Now.....what to do with that leftover beer......

Send it here, I'll take care of it!

Sent from my Redmi Note 5
-
(Oooops, I lost track of my numbers. I entered Day 05 two days in a row and fell behind in my sequence. Back on track with Day 10, today. :-)
Making Welsh Rarebit (always called Welsh Rabbit here) for lunch. Recipe calls for 1/2 cup of dark beer.

Dutch_Tooler can feel well assured that the cap lifter on the Ulu works very well!

Now.....what to do with that leftover beer......


I’m sure it will come to you!
-
Day #10 - little guy help during the groceries run unpacking, but completely forgot to take the action picture...

Here's a picture nonetheless!

Sent from my Redmi Note 5
-
That'll work! -
@FInixNOver said:
Day #10 - little guy help during the groceries run unpacking, but completely forgot to take the action picture...
Here's a picture nonetheless!

Sent from my Redmi Note 5
Nice

-
Nix's Sheath Tutorial -- Part Three
Piecing out the leather.
In the last part of the tutorial, we came up with a design. So far it has cost us a little ink and a scrap of cardboard. Not a big deal. But next we are going to cut into that nice piece of leather, so it’s a good idea to check things over. Is the belt loop on the correct side? Is it big enough? Did we allow enough room for the welt?
Once the design and template seem to be right, it’s time to translate the template into pieces of leather.
The first step for me is to trace out the template onto the leather. Then the sheath profile get cut out from the leather. We’re committed now!

It’s good to be precise with these cuts. I’ve left a bit of margin, which is not helpful, but won’t be a problem.
Next, I cut my welt template out of the master template:

Now you can see why I drew the welt line onto the master template. Using the welt template, I laid out the primary welt on a piece of scrap leather (4mm thick).
Then I cut out the secondary welt template or spacer template from the primary welt template.
I’m only going to use one (1) secondary welt with this sheath. If the handle were thicker, I might consider using an extra welt to give the handle more space in the sheath. Keep in mind, the more layers of leather you have, the tougher it becomes to sew them all together.

After laying out the secondary welt, I realized that I has a scrap piece of leather that would be perfect for my secondary welt. So, I’ll use the scrap instead of cutting out a fresh piece. The scrap is a bit oversize, but that won’t pose a problem. The excess will get trimmed off after glue-up.
The next few steps will be: 1) cutting in some grooves on the inside of the sheath to help make folding easier, 2) gluing in the welts, and 3) sewing down the belt loop.
However, the end of the belt loop should not be left square. Sharp corners on a sheath are not strong and easily snag, leading to torn stitches and a failed belt loop. So we really should shape the end of the belt loop. It is easiest to do this now, while the leather is dry and flat.
Here was my technique:
I made a straight line across the strap. I then used the rim of a jar to trace a curve from one side of the line to the end of the loop. Then the same on the other side. My two curves meet in the center line (basic geometry) and give me a clean shape to stitch down later.

The excess got trimmed off:

So, I now have my leather pieced and ready to start assembling. I used the template to mark a center line on the inside of the sheath. I also marked out the position for the welt to be glued in. Those lines will be helpful for the next steps.

That as far as I got today. Hopefully, I’ll get more done tomorrow.
-
Gorgeous knives and way to go Nix!!
-
Thanks, Barry.
I hope I'm not being too boring with a fairly mundane subject. There were a few people interested, so I also hope this is helpful.
Some more tricks and tips to follow......
-
I hope I'm not being too boring with a fairly mundane subject. There were a few people interested, so I also hope this is helpful.
Some more tricks and tips to follow......
I’m one of the interested ones and it is not boring at all. You are doing an excellent job! Looking forward to the rest.

-
Thanks, Barry.
I hope I'm not being too boring with a fairly mundane subject. There were a few people interested, so I also hope this is helpful.
Some more tricks and tips to follow......
I’m one of the interested ones and it is not boring at all. You are doing an excellent job! Looking forward to the rest.


-
Day 7-10 Catch up. Carried my Coast again at work Friday, though it wasn't needed this time. Went ice fishing up north this weekend, caught a whole lotta nothing. But my Mora rode on my hip all weekend and saw use trimming lines, cutting food, helping get the fire going, opening a few cans of everyone's favorite beverage(it was about 15 degrees F with 30 mph winds, the gloves were not coming off)




-
Ice fishing is funny that way. Some days you hit 'em, some days you don't.
Still, always fun to get out!

-
@Higgins617 said:
Day 7-10 Catch up. Carried my Coast again at work Friday, though it wasn't needed this time. Went ice fishing up north this weekend, caught a whole lotta nothing. But my Mora rode on my hip all weekend and saw use trimming lines, cutting food, helping get the fire going, opening a few cans of everyone's favorite beverage(it was about 15 degrees F with 30 mph winds, the gloves were not coming off)



Great photos! And great usages.

-
Day 10
Currently sitting at the airport, waiting for the wife to arrive. Not much cutting done today, mostly cleaning up the messes I made while she was away!![emoji3]

Ken
Sent from my iPhone using Tapatalk
Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login



