February Fixie Challenge
-
I got started early making a marinade for an Indian-inspired pork stew, and then getting the pork marinating.
Used the ulu to split and peel an onion. For the ulu, this requires two cuts. I didn't control the blade very well and you can see how one of the cuts veered off the center line. Not a problem. The onion got grated after this, so it really made no difference. But this wouldn't have happed with a chef's knife:

Next up, I peeled some garlic and ginger. I frequently hear people say the the easiest way to peel ginger is with a spoon. I don't get that. Why go dig up a spoon, when you already have a a knife in your hand? I used the sharp spine of the ulu to scrape the ginger, the blade to trim it up, before it all got grated and added to the marinade.

Once the marinade was made, the pork loin need to get chunked up.

Big piece of meat for a little knife. You can see here that the ulu can't cut cleanly through this loin with a single cut. I ended up using two-three slices to get through the meat and cube it.

Despite it's inherent limitations, the ulu did a great job. My complaints are fairly trivial. (And dinner is smelling good already. :D)
That ulu is like the Little Engine that could...it is doing it.

-
day 12: right tool for the right job?
<a href="https://flic.kr/p/QXvgkK" target="_blank" rel="noopener noreferrer"><img src="https://farm8.staticflickr.com/7861/32133241997_8253a7eead_k.jpg" alt="banner" style="max-width: 100%; height: auto;" /></a>2019-02-12_08-32-50
Maybe if you plan on chopping it to pieces

Sent fra min FRD-L09 via Tapatalk

-
@styx said:
day 12: right tool for the right job?<a href="https://flic.kr/p/QXvgkK" target="_blank" rel="noopener noreferrer"><img src="https://farm8.staticflickr.com/7861/32133241997_8253a7eead_k.jpg" alt="banner" style="max-width: 100%; height: auto;" /></a>2019-02-12_08-32-50
Not my first choice but looks like it worked for you! Nice

-
Hopefully getting home tomorrow. Ice can sure put a crimp in things!

-
day 12: right tool for the right job?
<a href="https://flic.kr/p/QXvgkK" target="_blank" rel="noopener noreferrer"><img src="https://farm8.staticflickr.com/7861/32133241997_8253a7eead_k.jpg" alt="banner" style="max-width: 100%; height: auto;" /></a>2019-02-12_08-32-50
Maybe if you plan on chopping it to pieces

Sent fra min FRD-L09 via Tapatalk
actually it has gone to hell so just might chop it

So no R.I.P. then
-
@FInixNOver said:
Day #12 - mail call! Opened a package containing a new fixie!Disclaimer: you'll most likely recognize it, although it's but a clone... [emoji21]
I have to be honest, I like all things blade, but so far, I've been more of a folding knife (SAK's and others) kinda guy. Mainly due to the fact that most of my weekly time is spent in an office environment, therefore, justifying the need for a proper fixed blade, has never really been a priority.
Participating in this challenge, has made me realize some of the benefits of carrying one and also some of the limitations that come with it. For the reason already mentioned above, I chose a very small blade that I could easily conceal and neck carry. I already knew I couldn't perform many of the tasks that a bigger blade can, but I find myself wanting to use it more only to realize that there's plenty it cannot do.
Once I saw the knife, that arrived today, online at a great price, I decided to order it. This one is still small enough to avoid raising too many eyebrows, but big enough to perform some of the tasks I find myself unable to perform with the fixie I chose for this challenge.
As I said in the beginning, I intend to use the same blade throughout the challenge, so I'll carry this one in my backpack as backup, and will use it when my main one isn't up to the task. Hopefully, I will not have any more "no use days" until the end of the challenge.I must apologize for purchasing, yet another clone, but I really wanted to make sure I can justify a fixed blade in my daily life, before I dive into the good, more expensive stuff!

Sent from my Redmi Note 5
No need to apologize - it is some sound reasoning on your part. I was going to start this Challenge with the Esee Izula but after over 2 years of caring it I was ready for a different fixie and went with the Triathlete. I think you will like it.

-
Day #12 - mail call! Opened a package containing a new fixie!
Disclaimer: you'll most likely recognize it, although it's but a clone... [emoji21]
I have to be honest, I like all things blade, but so far, I've been more of a folding knife (SAK's and others) kinda guy. Mainly due to the fact that most of my weekly time is spent in an office environment, therefore, justifying the need for a proper fixed blade, has never really been a priority.
Participating in this challenge, has made me realize some of the benefits of carrying one and also some of the limitations that come with it. For the reason already mentioned above, I chose a very small blade that I could easily conceal and neck carry. I already knew I couldn't perform many of the tasks that a bigger blade can, but I find myself wanting to use it more only to realize that there's plenty it cannot do.
Once I saw the knife, that arrived today, online at a great price, I decided to order it. This one is still small enough to avoid raising too many eyebrows, but big enough to perform some of the tasks I find myself unable to perform with the fixie I chose for this challenge.
As I said in the beginning, I intend to use the same blade throughout the challenge, so I'll carry this one in my backpack as backup, and will use it when my main one isn't up to the task. Hopefully, I will not have any more "no use days" until the end of the challenge.I must apologize for purchasing, yet another clone, but I really wanted to make sure I can justify a fixed blade in my daily life, before I dive into the good, more expensive stuff!

Sent from my Redmi Note 5
Nice! A new blade is always fun

Sent fra min FRD-L09 via Tapatalk
And that too!

-
RF i cant wait to see the new blade and bog Oak handle
I used to come across bog wood a lot but it was always too soft to do anything with, needs a bigger tree buried deeper i think, one day 
That ulu is like the Little Engine that could...it is doing it.


The new knifeblade was not quite as good as I had hoped so I might get a different blade for the bog oak

Sent fra min FRD-L09 via Tapatalk
-
Yes, but I just unburied the car and have one more shift before my long weekend! I have a Buck 119 that I inherited from my uncle waiting at home that I want to try here. I'm looking forward to seeing what it's got!
-
Take good care of yourself, Barry!
-
Thanks buddy! 👍
-
My evening snack

-
Thanks guys

RF i cant wait to see the new blade and bog Oak handle
I used to come across bog wood a lot but it was always too soft to do anything with, needs a bigger tree buried deeper i think, one day 
That ulu is like the Little Engine that could...it is doing it.


The new knifeblade was not quite as good as I had hoped so I might get a different blade for the bog oak

Sent fra min FRD-L09 via Tapatalk
guys! -
Nix's Sheath Tutorial -- Part Five
Assembly.
As noted, I’m going to sew this sheath. Sewing is incredibly strong and durable. Maybe more so than other techniques.
However, you could use rivets or staples to assemble your sheath. Some sheath makers like to use rivets to attach the belt loop, the reasoning there is that the knife could accidentally cut the stitching and detach the belt loop. Not likely an issue with rivets. However, rivets can wear the leather and weaken over time. So I don’t buy this approach.
In my opinion, sewing is the way to go.
If you are concerned about the stitches getting cut, you can protect them a bit by cutting a stitching groove into the interior of the sheath. But I find that when the stitches are well tensioned, they sort of sink into the soft interior anyway, so I don’t bother.
Maybe I will change my approach if I lose a knife due to a detached belt loop.
Before I get started, I want to discuss the preferred stitch for leather work: the Saddle Stitch.
This stitch is very strong and requires no knots to finish off. Saddle makers have been using this stitch since saddles were invented and there’s no reason to do it differently as far as I can tell. Moreover, it is self locking in leather.

To use the saddle stitch, two needles are place on one piece of thread, one at each end. One needle is passed through the leather from front to back, the other from back to front.
But how long a piece of thread?
I learned that you’ll need 7-8x the length of the stitch line. So, for 3 inches of stitching, you’ll need about 24 inches of thread. I once ran out of thread with a few inches of stitching to go, and now I use about 10x as much thread as the length of the stitch. This turns out to waste a bit of thread, but I’m not in business, and running out of thread isn’t fun.
It’s not really a problem if you do run out of thread, but you’ll end up with some funky looking stitches in the middle of your stitch line.
The other challenge is trying to get nice even stitching. Even stitching is really beautiful. My stitching tends to be ok. There are two factors that help your stitching be even: 1) clear marking, and 2) even, consistent tension on the thread, on both sides.
Another factor is not manipulating the leather too much. Since we have ‘cased’ the leather and it is a bit damp, if we tug on the leather we can actually bend and distort it. So being careful in the way the leather is handled also makes a difference (I know because I consistently mess this up and my sheaths and stitching end up looking a bit messy. )
To get the stitching marked out evenly, I use a couple of different tools. Don't worry, you can just use a ruler or gauge and mark your holes directly on the leather.
Here are three options I use:

- plain piece of leather with even intervals marked. This can be handy because it works around curves to a degree (more so if you use a thin thong as a gauge.
- “Pricking irons”. These are a set of small awls that have teeth spaced about 7 per inch. I really like these as they mark consistent, clear holes.
- a rotating stitching marker. I ran this toothed wheel over the scrap leather. You can see it makes a nice even pattern to follow. However, with a bit of pulling and tugging on the leather, the marks can fade out. The wheel is great for running around curves. I like to use a fine pen to mark the stitch points after I run the wheel over my stitching lines.
Enough talking, let’s get that belt loop sewn in so I can show you some more details.
With my first couple sheaths, I glued my belt loops in place before stitching. But….I found that if the glue got a bit messy it was hard to clean it up. And that mess could affect the way the stain came out during finishing. So I stopped gluing my belt loop in place, and just stitch it now.
First a quick check to be sure a belt will fit:

Now, I simply punch in a starter row of holes, using those to ‘tack’ the tab of the belt loop in place, and then I finish marking my stitching holes.

First few stitches in place:

At this point, I like to ‘back-stitch’ my starter holes. This is nothing more than stitching backwards through the same holes. This locks the thread in place (through friction). I don’t think this step is necessary, but it increases my confidence in the strength of the stitch. I always back-stitch at least four (4) stitches.
Here I’m using the round awl to re-open one of the holes so I can start back-stitching.

So after back-stitching, my thread is locked in and the belt loop is ‘tacked down’. I finish laying out the rest of my stitching holes.
My layout isn’t perfectly symmetric, but don’t sweat it, you’ll do better.

Now the stitching can be finished up:

At this point, I’ve stitched all the way around the edge of the belt loop tab. To lock the stitching in, I need to back-stitch at least 3 stitches (I go a minimum of 4 stitches). Four stitches leaves one end of the thread on the inside of the sheath, and one on the outside. I take the outside thread and back-stitch it once more to get it on the inside.

This way, the stitching is locked in, smoothly transitioned, and the tag ends are hidden on the inside.
You could clip these with a nail clipper, but I left them long so you could see what was going on. The tag ends won’t be a problem.
With the belt loop sewn in, we can close the sheath up and stitch it the rest of the way.
I use more glue to get the folded sheath to hold in place. This isn’t necessary, but it makes things easier for me. You could just clamp the sheath closed and sew it up. But, for me, gluing it together just makes sense.

Once the glue is dried, I dampen the spine of the sheath, again to make it easier to flex and fold. Folding dry leather isn’t good for the leather and is much more difficult.
Glued!

Technically it’s a sheath now….but not one that will last long. We still have to sew this sheath up.
You could just use an awl and needles and stitch it up now. I prefer to to a bit of layout. I use either a stitch groover or a pair of dividers to trace a parallel line along the edge of the sheath.

The grooving tool actually cuts a thin bit of top grain out of the leather. Technically this weakens the sheath a bit (most of the strength in leather is in the top grain.), but it also provides a small space for the stitching to sit down in, which may protect the stitching from abrasion a bit.
I don’t know how much of this is theoretical and how much is practical.
The dividers work best if the leather is dampened. They leave a slight indentation. That is nice, except when the leather is getting worked; sometimes that indentation gets erased as the leather gets manipulated.
The divider idea could be duplicated easily by just using two nails driven through a thin piece of wood at the appropriate width for your project. I used this technique for my first sheath and it worked just fine.
For this sheath, however, I used the grooving tool.

The little groove at the top is purely decorative. Just an accent line.
To layout my stitching points, I used the pricking irons. These make nice clean holes. I started out in the corners. The number of stitching holes may not line up perfectly with these irons. I don’t want a short stitch landing just in front of a corner (that would look odd). So I always start my layout in the corners and then cheat somewhere in the middle. Even with the pricking irons, I'll still need to use a sharp awl to complete the holes.

In this case, the stitching holes came out pretty close to perfect. Just luck.

I start at the top corner and work my way down and around to the bottom tip. Again, though, I start four stitches below the corner and stitch up to the top:

Then I back-stitch down. This locks my threads in at the start.

I then just stitch my way all the way to the end. This shot was just to remind me to say that as you stitch, be sure to apply even pressure to each end of the thread as you go. After each stitch, I give each end of the thread a little tug.

Not great, but not bad.
Here I have reached the end of the stitching line. I’ve also added a diagonal row of stitching marks to secure the wide portion of the welt in the corner. This will also allow me to add a tie-down hole later.
I’m just going to back-stitch my way to the diagonal and then stitch up the diagonal.

After stitching up the diagonal, I back-stitched (perhaps ‘over-stitched’ is a better term) back down the edge.
We now have an actual sheath!

I tested the fit….

It’s snug!
The knife has ended up a bit deeper than planned. There is still a bit of trimming to be done, so we’ll see how it ends up.
You can see I also took a punch and cut a tie down hole in the bottom. This isn’t a drain hole. The stitching and cement will have made the edge nearly water-tight. I won’t really use it as a tie-down, but I thought it was fun to throw in. Might have been centered a bit better, but I was in a rush to get dinner made.
At this point, I’d be a bit surprised if you weren’t thinking something like, “uhh, Nix, that sheath looks like a hot mess……” Yeah, me too.
But we still have more to do and these things seem to improve with a bit of attention and finishing. That will have to wait though……….
-
Great pics today gents

Another fabulous chapter in sheath making, Nix
I love the sewing aspect of this and never knew how some of this was accomplished
I have leather and was thinking of making some type of sheath but I have always used rivets
I may try to sew one
and yes if I do I will take pics :D Unless it ends up a hot mess
:ahhh :D -
Poncho, the pros make this stuff look so easy....or is that 'sew easy'? It isn't. I wish I had better skills, but I suppose practice helps. Regardless, it's fun.

I will say, that just in doing this tutorial I've learned a couple new things and have a few new ideas to try out next time.

.....which means I'm gonna need another knife........

-
@Nix said:
Poncho, the pros make this stuff look so easy....or is that 'sew easy'? It isn't. I wish I had better skills, but I suppose practice helps. Regardless, it's fun.
I will say, that just in doing this tutorial I've learned a couple new things and have a few new ideas to try out next time.

**.....which means I'm gonna need another knife........ **

Best excuse I have heard in a while :D
Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login
