February Fixie Challenge
-
Great pic and nice Mora Borg!
-
Busy day for the 119. Unfortunately I'm limited to carrying it while I'm out here in the sticks with the way the ordinance is written, but I typically avoid town anyway! I'm looking forward to putting it to work in the kitchen to see if it does as well as it's folding brother, the mighty 110.


-
So tonight is the night for sewing,

I don't have one of those fork things so i just stole one from the kitchen, i figured it would be a good hole distance marker if nothing else, i then used the awl to poke all way through, the awl was a screwdriver a couple of hours ago but i ground it down to a point as i couldn't find mine

All ready to sew, looks rough as hell but it's not like i'm making it for Versace, it'l do :D
Found a needle, strung two on and get going...thread falls off needle, every time it slides off i have to cut it a bit to reload, this happened a few times.. it's getting shorter and i think it's too short as it is, so i cleverly decided to tie a knot on it, the knot is too big and snags in the hole..tie a smaller knot and now i am two stitches in..needle breaks, i'm going for a coffee..i might go back to it later

-
Thank's Barry, that 119 sure looks capable

Thanks RF

-
day 14: isn't she lovely.....
-
@Borg said:
So tonight is the night for sewing,
I don't have one of those fork things so i just stole one from the kitchen, i figured it would be a good hole distance marker if nothing else, i then used the awl to poke all way through, the awl was a screwdriver a couple of hours ago but i ground it down to a point as i couldn't find mine

All ready to sew, looks rough as hell but it's not like i'm making it for Versace, it'l do :D
Found a needle, strung two on and get going...thread falls off needle, every time it slides off i have to cut it a bit to reload, this happened a few times.. it's getting shorter and i think it's too short as it is, so i cleverly decided to tie a knot on it, the knot is too big and snags in the hole..tie a smaller knot and now i am two stitches in..needle breaks, i'm going for a coffee..i might go back to it later

Just take a break and go back to it later.
It's looking good so far
Sent fra min FRD-L09 via Tapatalk
-
+1 from me Borg. Looking great. Love the colour.

-
Thanks RF, Max

Coffee works wonders, went back to it and all went well...

The more observant among you will have noticed a little issue with it, yup i ran out of thread

A complete botch up job at the bottom with saddle stitch turning into single stitch to save thread and it became apparent single stitch wouldn't even have done it so its just a mess with a glued knot..it's a sheath though right? :D
Off to Amazon i go, i will redo it completely, in hindsight i should have started at the bottom and when i ran out at the top i could have just cut the whole thing off and made it shorter, we live and learn

A wise man once said ..
"I learned that you’ll need 7-8x the length of the stitch line. So, for 3 inches of stitching, you’ll need about 24 inches of thread. I once ran out of thread with a few inches of stitching to go, and now I use about 10x as much thread as the length of the stitch. This turns out to waste a bit of thread, but I’m not in business, and running out of thread isn’t fun.
It’s not really a problem if you do run out of thread, but you’ll end up with some funky looking stitches in the middle of your stitch line" - Nix
I would go along with that

-
@Barry Rowland said:
Busy day for the 119. Unfortunately I'm limited to carrying it while I'm out here in the sticks with the way the ordinance is written, but I typically avoid town anyway! I'm looking forward to putting it to work in the kitchen to see if it does as well as it's folding brother, the mighty 110.Like the Buck 119.
I have one from mid nineties but would like to get an earlier one to match my ‘74-‘80 110. -
Coffee works wonders, went back to it and all went well...

The more observant among you will have noticed a little issue with it, yup i ran out of thread

A complete botch up job at the bottom with saddle stitch turning into single stitch to save thread and it became apparent single stitch wouldn't even have done it so its just a mess with a glued knot..it's a sheath though right? :D
Off to Amazon i go, i will redo it completely, in hindsight i should have started at the bottom and when i ran out at the top i could have just cut the whole thing off and made it shorter, we live and learn

A wise man once said ..
"I learned that you’ll need 7-8x the length of the stitch line. So, for 3 inches of stitching, you’ll need about 24 inches of thread. I once ran out of thread with a few inches of stitching to go, and now I use about 10x as much thread as the length of the stitch. This turns out to waste a bit of thread, but I’m not in business, and running out of thread isn’t fun.
It’s not really a problem if you do run out of thread, but you’ll end up with some funky looking stitches in the middle of your stitch line" - Nix
I would go along with that


Should be a simple job to re-stitch it. You have the basis of a good sheath there.
-
Day 14:
Well….it turns out that I do have another knife that needs a sheath.
This little ‘Personal’ by Bob Dozier came with a lovely kydex sheath, however; I’ve always felt a knife of this quality needed some leather. So, fresh off the knife tutorial, I started a new sheath, but using a slightly different t approach.

If I didn’t say it in the original tutorial, I don’t think there is one right way to make a sheath. For this sheath I’m going to do things a bit differently, just to put a few additional ideas out there for your consideration.
Don’t worry, there won’t be a series of lengthy posts. I’ll try to keep it concise and focused (to the best of my ability).
As you see, I’ve traced the outline of my knife onto a file folder (these are great for laying out sheaths!).

I’ve added more curves this time.
My template includes: sheath, welt, belt loop, and belt loop spacer (more on that later).

I tried to be precise when cutting out my pieces, but I’m not the most skilled ‘artisan’.

Note: I was intentionally imprecise when cutting out the outside edge of the welt. I want that to be a bit ‘generous’, so that I can trim it flush later.
This time I went ahead and dyed my pieces straight after cutting them out. I still have to do more dying leter, but this will give me a chance at having a more even finish. (I should have dyed the edges of my belt loop and spacer here, too, but that will get taken care or.)

I glued the belt loop spacer to the top of the belt loop (and dyed and burnished it) and then sewed the loop to the sheath (right hand carry).
This does two things: 1) it creates some natural space for the belt to slip through, and 2) it relieves pressure on the sheath and stitches. I don’t think I’ve seen this anywhere else. I can’t be the first person to try this. I just hope that it hasn’t been tried before and found to be a bad idea.

Here’s a shot of the belt loop & spacer prior to being sewn in. It got burnished more later.

I have added a spacer to other sheaths and it seems to have worked out really well. I'm hoping this one does, too.
If you look at the lower part of the belt loop, it looks a bit….ehrrrr…mangled. I tried to dampen the leather and ‘wet form’ the lower part to form a natural curve or bend to accommodate the belt.

This worked to a slight degree, but distorted the leather and made sewing it up a bit of a problem. I think there are ways to do this better, albeit taking more time.
I think adding the belt loop spacer is worthwhile, wet forming the lower part of the loop doesn’t seem quite as useful to me at the moment.
OK, so that is as far as I’ve gotten today. Reasonable chance this sheath will be finished tomorrow.
It is sitting out with a temporary spacer in the loop while it all dries, to keep the loop open.

More to follow tomorrow. (And the Ulu did get used to trim some edges. It works very nicely in the role of leather workers curved knife.)

-

Borg, you reminded me of a trick (I don't always use it, that's why I forgot to mention it) to secure your thread on a needle.
- thread the needle as per usual.

- take the point of the needle and stick it through the end of the thread

- pull end of the thread down over the eye, and then tighten the main part of the thread.
This is a great trick, especially the running short on thread!

-
And, Borg, great job, especially having made you own tools!

For the bottom of the sheath, you could use a rivet or a grommet to secure the tip. Just an idea......

-
Another great day of pics
More great pics of sheath making as well
and by 2 members now :o :ahhh
Nice job guys and can't wait to see the next steps in this sheath as well, Nix

-
Day 14
So I believe I have reached a limit with my fixed blade. As I have said in my previous post, it will make a good secondary knife but not as a primary carry.
And now, I will bring in a new fixed blade for the remainder of the challenge.
Ken
Sent from my iPhone using Tapatalk
-
Looks a good solid blade Ken. Sheath?

-

Sent fra min FRD-L09 via Tapatalk
-
So I believe I have reached a limit with my fixed blade. As I have said in my previous post, it will make a good secondary knife but not as a primary carry.
And now, I will bring in a new fixed blade for the remainder of the challenge.
Ken
Sent from my iPhone using Tapatalk
I like the look of that

Day 15:
Food duty at work.
-
@FInixNOver said:
Day #14 - mail call. Lanyard breakaway barrels.

Sent from my Redmi Note 5
That’s cool...

Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login


