And so it begins.... (My adventures into Alox!)
-
Pioneer Pruner + Pioneer Farmer + Pioneer Electrician + Pioneer X = Pioneer Magnum. :D
Awlsome!

Is that a main blade backspring you're using for the electrician+pruner blades layer?
Sent from my Redmi Note 5
Ya has to be the blade spring.
-
Pioneer Pruner + Pioneer Farmer + Pioneer Electrician + Pioneer X = Pioneer Magnum. :D
Awlsome!

Is that a main blade backspring you're using for the electrician+pruner blades layer?
Sent from my Redmi Note 5
Ya has to be the blade spring.
Last question:
Did you get good spring tension on both blades without any modification?Sent from my Redmi Note 5
-
@FInixNOver said:
Did you get good spring tension on both blades without any modification?Sent from my Redmi Note 5
Feels same as a normal blade to me.
-
I guess I keep forgetting about the difference between working with precision tools and mods like the ones I've done so far...

I need to point out that I only mod for my personal use, and would very much like to improve myself whenever possible. That being said, I have yet one more question, a request, let's say... Can you share the position for each of the 2 blades against the backspring, as it isn't symmetrical?Sent from my Redmi Note 5
-
I guess I keep forgetting about the difference between working with precision tools and mods like the ones I've done so far...

I need to point out that I only mod for my personal use, and would very much like to improve myself whenever possible. That being said, I have yet one more question, a request, let's say... Can you share the position for each of the 2 blades against the backspring, as it isn't symmetrical?Sent from my Redmi Note 5
[/quote].Do you mean the offset? Each side needs a 0.040" spacer on different sides but that becomes very obvious if you try to out them together as each is bent.
-
What I meant is which blade goes on the side where the main blade was supposed to be.
Sent from my Redmi Note 5
-
I finally found a source for nickel silver thick enough make a mag glass frame out of. I needed an option for people wanting a silver looking holder and Ti really doesnt make for a good option do to the sticky action.
-
Amazing as always! Looks really really good
[It's not failure if you learn something from it]
-
I caved and ordered some Timascus. Beautiful material but very expensive. About 400 USD for this 2x10 piece and this is the lower cost only one side is fancy patterned stuff, but it really is impressive looking material. From this I can get 4 scales and a bunch of crosses for inserts, once I get up my nerve to cut into it of course. :D
-
Soooo looking forward to the result!

Never heard of it before but looks magnificent.
-
@Mechanickal said:
Soooo looking forward to the result!
Never heard of it before but looks magnificent.
Its basically pattern welded Titanium. Only sold through alpha knife supply as they have the patent on the process. Ive seen it used by other knife makers for scales but never seen it in person until now.
-
Now it sounds even more expensive...
I honesty hope you'll build at least one set of scales with this. Even though that's easy for me to say, not having any funds in it...

-
@Mechanickal said:
Now it sounds even more expensive...I honesty hope you'll build at least one set of scales with this. Even though that's easy for me to say, not having any funds in it...

My plan is to make 4 front scales not sure it it will be pioneer size or standard 91. Probably 93 since this material is thick enough for the drawer option and that I do on front scales for pioneers. Im still deciding how to cut it up. I might hand cut a small cross from the corner to start off with and do a cross insert. Then I can see about heat anodizing.
AKS says the electro methods of anodizing on this material dont work as nice as heat anodizing. Not sure if heat is just heat or needs to be flame. If I could put it in an oven to anodize that would be nice, but not sure of what temp. So lots of playing and testing to see what works. :D
-
Even a drawer in these??!

I'm volunteering to do the end user testing phase

-
Forgot to post my single layer mod from last week. Only catch was the phillips lugs hit the scale and prevented it from closing completely. So I machined out some clearance pockets and it was good to go.
-
Nice Timascus...

-
Thin to win

-
What do you get when you take an 11 layer XLT and add 2 custom layers? I dont know, but it looks like this. :D
-
Holy crap that is a real beast!
[It's not failure if you learn something from it]
-
You took the words right out of my mouth!! [emoji50][emoji50]
Sent from my Redmi Note 5
Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login