Sak bushings.
-
I started off doing it by pre-forming but after a tip from tattoosteve I tried it the other way. It's a bit more fiddly but seems a lot more robust.
-
I've done a few mods now. All on 91s removing or adding layers. I've posted a couple. Nothing too spectacular, just customizing for my preference.
The damaged bushing is from my second mod before i started using a drill press. I used cobalt bits, I used a metal scribe and punched a started point for the bit....but when drilling.
I drilled out the rivit and i didn't notice the bit was off centre. So I damaged the bushing. It actually ended up on the bit as I was drilling. When I peaned everything back in place this bushing hole was larger....so i kept peening until the rod basically filled the bushing. It was tight, but not great.
When I put the scales on it needed glue to keep it in place. It's the only time I've had to use any adhesive.
I do things different now.
- Remove scales.
- Mark drill bit centre point
- Mount in drill press vice.
- Drill out just enough to punch rod down.
- Remove bushing and pull everything apart.
It was a learning experience. I picked up the tools to make it easier. Saves me time and makes things easier.
-
@hiraethus said:
Did you preform one rivet head before rebuilding the SAK? If you do this it can loosen over time, causing side-to-side play. Much better to cut and file the pin to length (about 1 ~ 1.5mm past the bushing or outer liner in the case of the back tool pivot) and peen tightly into the bushes on both sides as you build the knife.Sorry to bring back an old thread, but has anyone done any guides or got any pics of this technique? Seems like an extremely useful method to learn?
Thanks -
Not done so before, but the method I use is roughly as follows:
- Get your SAK assembled, with liners and bushes in place. You might want to tape the knife together to stop it coming apart while you work on it.
- Trim the rods to length and file/sand the ends flat - approx. 1mm proud of the bushes on each side is about right, and about the same proud of the liner on the back tool pivot
- Carefully peen one end of each pin over, just a little, to retain the bushing
- Flip the knife and do the same on the other side.
- Work all the rivets in turn - peen until just tight enough that the action is still good but there's barely any side-to-side play in the tools.
-
Thanks, that's kind of what I was thinking!
And is there a recommended drill bit diameter for drilling out each of the brass rods on each respective size of SAK? -
@craggus2000 said:
Thanks, that's kind of what I was thinking!
And is there a recommended drill bit diameter for drilling out each of the brass rods on each respective size of SAK?For 91mm SAK's the three pins with bushings are 2.5mm diameter - the fourth pin is 2.2mm but you're best off filing the head off and punching it through.
93mm SAK's have 3mm pins either end and 2.5mm in the middle.
84mm are all 2.2mm I think........
-

Except on a 91mm SAK, the two end pins are 2.5 mm and the two inner pins (one with bushings, one without) are 2.2 mm.
-
Presumably just use a 0.5-1.0mm smaller diameter drill bit than the rod?
-
I'd use 2.5 mm and 2 mm. They're easy enough to get hold of and, as long as you're careful with your centring (use a sharp punch, take your time) you'll be able to reuse the bushes no problem.
If you drill too deep you risk damaging the liners. Too shallow and you'll struggle to punch the rivet through the bushing.
Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login
