Gerber Mp600 owners club ;)
-
. My first new gerber purchase, I’m not so sure about it but I’ll carry it this week to try it out, and if I don’t like I’m sure it will look great in my collectionSent from my iPhone using Tapatalk
-
The thing to keep in mind is that the 600 is a very old design and not refined at all. But, that said, they will take a beating better than almost any other MT ever made. They just don't look pretty doing it. :ahhh
-
Another one striked off the wish list! Mp600 Fisherman. :D


-
@gregozedobe said:
Matching pair: MP400 & MP600
now, waiting for a Filk Fisherman to appear.. -
Sweet finds, Sam!

-
@gerleatherberman said:
Sweet finds, Sam!

-
im on day 3 of carrying the mp600, still not impressed so far, but im trying to remain open minded and give the tool at least a full week of service before jumping to conclusions

-
The 600 is an acquired taste. The taste is usually only acquired under the hardest MT uses. Particularly the pliers on the 600. Gerber pliers tool steel is the most resistant to damage I have ever used.
My first MT, and only one for over a decade, was an OG Multi-Plier. So I have a soft spot for the sliding pliers Gerbers. :)
-
New addition:
Early Prototype MP600 with Maroon finish. This is a genuine example, with Simonds marked file and pliers head with sprue marks.
Thanks again to gregozedobe for messaging me about it.






And a couple of shots with the early yellow/black/SS MP600 and red-cerakote Snap-On SMT97R(MP600 chasis/pliers and special toolset).


-
@gerleatherberman said:
New addition:Early Prototype MP600 with Maroon finish. This is a genuine example, with Simonds marked file and pliers head with sprue marks.
And a couple of shots with the early yellow/black/SS MP600 and red-cerakote Snap-On SMT97R(MP600 chasis/pliers and special toolset).
Nice MP600s

Is the finish on the Maroon prototype some kind of hard finish (not soft, easily chipped paint) ?
I only just noticed the locking tabs on the Snap-On are different to the regular MP600s (and I have 3 of the Snap-On ones, got the first one back in 2016 ! )
-
@gregozedobe said:
Nice MP600s

Is the finish on the Maroon prototype some kind of hard finish (not soft, easily chipped paint) ?
I only just noticed the locking tabs on the Snap-On are different to the regular MP600s (and I have 3 of the Snap-On ones, got the first one back in 2016 ! )
Thank you, Greg!

It appears to be more like a cerakote than an anodized(I am certain it is not anodized) or painted finish. It is quite tough and doesn't show the easy chipping of the yellow MP600(I checked with a very light knife scratch inside the handles). There is wear inside the handles where the pliers slide in and out(minimal though and only where the pressure is strongest), but I expect that with any non-oxide finish. My Snap-On has that already, just from opening it to take photos. The outside of the tool looks really good and has held up better in storage than the yellow/black/SS 600 has. :)
-
Wow! I really
the colour here! The maroon looked terrible in the ebay listing! Congrats again for the new addition!
on myself!! -
@Sam Lim said:
Wow! I really
the colour here! The maroon looked terrible in the ebay listing! Congrats again for the new addition!
on myself!!Thanks, buddy!

I kind of figured the listing photos were bad, because the SS tools has an "orangish" tint to them in the listing photos. It is a looker for sure, in person and in color-correct photos. :)
Well, I would say too bad/sorry, but you have some tools I cannot get my hands on as well. Cough.....fishermans....cough.
:D -
@gregozedobe said:
I only just noticed the locking tabs on the Snap-On are different to the regular MP600s (and I have 3 of the Snap-On ones, got the first one back in 2016 ! )I also meant to mention that the first tool I know of that had the updated tabs was the MP600 Sight Tool(maybe 2014? That is when my U.S marked - updated Multi-Plier stamp - Sight Tool is dated). It seemed to coincide with the introduction of the fantastic huge combo-edge blade on the Sight Tool and Snap-On.
-
Alright. After a lot of restoration work, I'd say the cutter head is at 98% of being unused.
Here is a photo of the 600 Cable broken down. Note the heavily dinged up cutter.

After fine-filing(diamong coated needle files) the cutters back to the right profile, I replicated the Gerber finish on the jaws as closely as I can, but I haven't figured out a way to make it perfect yet. Close enough for this 600Cable Cutter to go into the collection. :)
The rest of the tools were wire-wheeled(varying brass or fine steel wheel) and oiled before reassembly.

Cutter Head close-up after reprofiling and finishing.

And a couple of shots with the MP650, which I also received a cable cutter head for.


-
@gerleatherberman said:
Alright. After a lot of restoration work, I'd say the cutter head is at 98% of being unused.Here is a photo of the 600 Cable broken down. Note the heavily dinged up cutter.

After fine-filing(diamong coated needle files) the cutters back to the right profile, I replicated the Gerber finish on the jaws as closely as I can, but I haven't figured out a way to make it perfect yet. Close enough for this 600Cable Cutter to go into the collection. :)
The rest of the tools were wire-wheeled(varying brass or fine steel wheel) and oiled before reassembly.

Cutter Head close-up after reprofiling and finishing.

And a couple of shots with the MP650, which I also received a cable cutter head for.


:ahhh :ahhh I want one so bad!!
-
Thank you, Nick!

@Sam Lim said:
:ahhh :ahhh I want one so bad!!Thank you much, Sam!

I feel the same about the Fisherman tools you bought. Just super cool!
When I saw the listing for the Cable Cutter, I bought it without hesitation. Thankfully the tool turned out collection worthy. No parts needed changing out and the cutter head looks good. :)
-
@gerleatherberman said:
Thank you, Nick!
Thank you much, Sam!

I feel the same about the Fisherman tools you bought. Just super cool!
When I saw the listing for the Cable Cutter, I bought it without hesitation. Thankfully the tool turned out collection worthy. No parts needed changing out and the cutter head looks good. :)
Exact same thought when I saw the fisherman. But so far when I see the cable cutter on the bay, it's always price at a premium.. Even when usually my thinking "is buy once and get it over with" , its still too high.. :-\
Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login

