Old Timer Frustration
-
@ Frankki 1095 is great steel. The blades I have in 1095 have all been a joy to sharpen and get not only hair popping sharp but a few will easily cut toilet paper with ease. Some folks just love traditionals and 1095 is a standard for certain traditional knives.
Now that being said, I wont pay a premium for it

-
@Aloha said:
@ Frankki 1095 is great steel. The blades I have in 1095 have all been a joy to sharpen and get not only hair popping sharp but a few will easily cut toilet paper with ease. Some folks just love traditionals and 1095 is a standard for certain traditional knives.Now that being said, I wont pay a premium for it

Aye, loads of people swear by 1095 and report great results, I just can't replicate those achievements. Freehand or guided, natural stones or ceramics, for me it always gets only "just so" sharp. Entirely possible that I have been spoiled by the modern stainless alloys, but what can I say, my own results have been only adequate. I'll go with stainless, even the lowly 440A, in traditionals these days. More premium alloys always welcome but not widely available unless you go custom.
-
Bummer its not behaved well for you. I would like to see more steels used in traditionals tho I'm sure if I looked hard enough and paid up for a custom I could locate one.
not so sure at that point my pockets could handle the sticker shock :D. -
Is it a made in USA OT or one of the newer Taylor brand ones. ? All my old Schrade's have great steel on them and are no trouble to get shaving sharp.
-
@SteveC said:
Is it a made in USA OT or one of the newer Taylor brand ones. ? All my old Schrade's have great steel on them and are no trouble to get shaving sharp.It's a USA one. I might pass it off to a guy at work who is known to work well with his lanky. I figure that would be a good test to see if it is knife or simply me.
Sent from my SM-G920V using Tapatalk
-
@Aloha said:
Bummer its not behaved well for you. **I would like to see more steels used in traditionals tho I'm sure if I looked hard enough and paid up for a custom I could locate one. **
not so sure at that point my pockets could handle the sticker shock :D.Have you looked at the Collectorknives and Lionsteel colaberations.
CK also sells a colab with Maserin called the plow.
-
@Anka said:
I have a Shrade Old Timer 3 blade stockman that was purchased second hand. The knife was dull and I have recently tried to bring it back into shape for carrying. I was able to get the sheepsfoot to push cut newspaper but the spay and main clip point are making me pull my hair out. It's as if the edge keeps rolling or braking off.Spent the better part of 6 hours on this knife over the last two days. Touched up some of my other knifes also and each got near shaving sharp fairly quick. Anyone else ever run into a knife that just would not play nice?
Sent from my SM-G920V using Tapatalk
You could try a convex edge with wet/dry sandpaper. I used this method with my Old Timer and was able to get it razor sharp. Like scary sharp. And I'm far far from a sharpening expert.

-
I have an Old Timer Stockman that is exactly like that. I've tried everything I can over the years and still can't get it to hold an edge. I bought it new many years ago and it's been like that since I got it. It's sad because it would be perfect to carry in a watch pocket.
-
I wonder if someone got a bit happy with a torch at some point and burned off the edge and ruined the heat treat in the blade? Or used a grinder/electric sharpener and overheated the edge?
If not, then the blade is part of a batch that wasn't made and/or treated properly. I have always gotten ole' carbon blade traditionals super sharp with ease. I just don't care for them(for EDC), because the edge corrodes off in my pocket if I don't take care of it.
The only Schrade traditionals I carry are the + versions(stainless). Harder to sharpen, but my no-good lazy knife-ways work better with them. -
@clown said:
You could try a convex edge with wet/dry sandpaper. I used this method with my Old Timer and was able to get it razor sharp. Like scary sharp. And I'm far far from a sharpening expert.
I started with the sandpaper and mousepad method. Never even got close to a workable edge with it although I have used it on many diffe rent knives before. Moved to free hand on a stone after.
Sent from my SM-G920V using Tapatalk
-
@Barry Rowland said:
I have an Old Timer Stockman that is exactly like that. I've tried everything I can over the years and still can't get it to hold an edge. I bought it new many years ago and it's been like that since I got it. It's sad because it would be perfect to carry in a watch pocket.It really is a shame, the knife is in great shape with a wonderfull natural patina otherwise. I would love to carry it.
Sent from my SM-G920V using Tapatalk
-
Try a diamond stone. I had a 106OT give me a lot of grief, and my extra fine DMT pocket sharpener finally got a good edge on it. Seems with me, knives that didn't see much use and have an old factory edge that was never resharpened are a pain to get a good edge on. I've got a Buck 303 that will not get an edge. I think it was actually made by Schrade (before Buck started making the 3XX line in-house); it could very well be a heat treat problem.
-
"Entirely possible that I have been spoiled by the modern stainless alloys, but what can I say, my own results have been only adequate. I'll go with stainless, even the lowly 440A, in traditionals these days"
I would have thought it would be the other way around.
Have you tried different grits/angles? I've read that using coarser grits than you would normally associate with a fine edge then going straight to a strop works for some.(toothy) Personally all the Schrade's and any other 1095 that I've had have resulted in a good edge.
You could try to pick up another cheap 2nd hand schrade 1095 and see if you can get it sharp. If so then the heat treat as mentioned may be the problem.

-
After reading some of the comments and thinking about my 1095 blades, I think the heat treat could very well be the issue. Not necessarily from the factory but who knows? The previous owner could have some how done something since the main blade is part of the issue
.I do like the idea of convexing the blade. My Cased Sod Buster Jr came to me with a convexed blade and was very sharp. I later reprofiled it to 15dps. Its wicked and stays sharp.
I do hope you sort this out. I also want to add that I am a big fan of stropping and checkin the edge with a loop. It could be that the edge isn't apexed prior to moving to the other side? Could be some rounding if you are stropping? Could be the wire is just pushed to one side after the initial sharpening?
Just thinking out loud.

-
+1 on the loupe. I use one often to get a close look at what’s going on with the edge. (and my close vision is rubbish these days).


-
@sak60 said:
"Entirely possible that I have been spoiled by the modern stainless alloys, but what can I say, my own results have been only adequate. I'll go with stainless, even the lowly 440A, in traditionals these days"I would have thought it would be the other way around.
Have you tried different grits/angles? I've read that using coarser grits than you would normally associate with a fine edge then going straight to a strop works for some.(toothy) Personally all the Schrade's and any other 1095 that I've had have resulted in a good edge.
You could try to pick up another cheap 2nd hand schrade 1095 and see if you can get it sharp. If so then the heat treat as mentioned may be the problem.

Actually, come to think of it, I may have proven myself wrong already. I remembered that I actually do have one knife in 1095, the sharpness of which I'm pleased with: an Ulster 10OT from the 1960s, also belonging to the Schrade cutlery family. Previously I had tried other Schrades, a Queen-made Bulldog and a couple of Camillus knives - never a good enough edge. The little Ulster barlow somehow managed to surprise me!

-
@Frankki said:
Actually, come to think of it, I may have proven myself wrong already. I remembered that I actually do have one knife in 1095, the sharpness of which I'm pleased with: an Ulster 10OT from the 1960s, also belonging to the Schrade cutlery family. Previously I had tried other Schrades, a Queen-made Bulldog and a couple of Camillus knives - never a good enough edge. The little Ulster barlow somehow managed to surprise me!

I have an Ulster Boy Scout knife and it gets really sharp. -
No worries bro, you're not alone. I've had nothing but trouble with these myerchins they've issued to us. I have guys come up to me all the time asking to sharpen their blade for them. No matter what you do it'll be hair shaving sharp when you're done, and dull as a butterknife right after you use it next. Plus the bearings on all of then get loose rather quickly :ahhh :ahhh

-
@Aloha said:
After reading some of the comments and thinking about my 1095 blades, I think the heat treat could very well be the issue. Not necessarily from the factory but who knows? The previous owner could have some how done something since the main blade is part of the issue
.I do like the idea of convexing the blade. My Cased Sod Buster Jr came to me with a convexed blade and was very sharp. I later reprofiled it to 15dps. Its wicked and stays sharp.
I do hope you sort this out. I also want to add that I am a big fan of stropping and checkin the edge with a loop. It could be that the edge isn't apexed prior to moving to the other side? Could be some rounding if you are stropping? Could be the wire is just pushed to one side after the initial sharpening?
Just thinking out loud.

Sak60, this is for you also. What magnification loupe do you recommend? I have been thinking about picking one up.
I have done well with most of my knives with just a mouse pad and 1200grit paper. I really need to go pick up a 600 grit though. But honestly I haven't yet achieved shaving sharp with the mouse pad/ sand paper. Have gotten much closer free hand with a small stone. I also don't have a real strip yet but I am planning to get a small piece of 2×4 at work and affix some denim to it to make my own. Already have some green compound
Sent from my SM-G920V using Tapatalk
-
Hi Anka, I can only say that the loupe that I use is 10X and is designed for geology use originally I think and find it quite powerful enough to see different grind angles, if the apex has any spots that are missed, and even see the individual scouring marks left by the stone. A strop will really benefit you. I made mine with some scrap wood and leftover leather from sheath making.
I have never used a mouse pad so can’t comment on that. If I use the strop method for a convex blade I just lay the wet and dry paper over my strop and use that. My thinking is the angle of sharpening and stropping is easily maintained.
I have wet and dry grits from 400 up to 2000 with 600 to 1200 the most used.
Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login
