Micra Disappointment
-
@gerleatherberman said:
The CrossCuts are hit and miss. The US versions aren't good at all, and half of the 2.0s are not aligned properly. But, after some back and forth with SOG replacements, I ended up with two fantastic examples(one for the collection and one that is always clipped to my belt loop with a backup light[mag solitaire led]).
Imagine cutting through jumbo zip-ties like they were butter. :)What!!
sog! My specimen is probably the missed batch then! -
I had one CrossCut that was so bad, that the jaws didn't even make edge-contact until the very tips.

-
Had my Micra for many years. Used the h_ll out of the sissors. Never had an issue until maybe the last six months. The sissors aren't so tight anymore. Thought about buying a new one but now I wonder if the build quality has gone down over the years?
And is there a way to fix the gap in the sissors? A bit of sentimental value on this one. -
@MickeS said:
Had my Micra for many years. Used the h_ll out of the sissors. Never had an issue until maybe the last six months. The sissors aren't so tight anymore. Thought about buying a new one but now I wonder if the build quality has gone down over the years?
And is there a way to fix the gap in the sissors? A bit of sentimental value on this one.Peening it might help.
Sent from my iPhone using Tapatalk
-
If its any consolation, my brand new 30th anniversary edition Micra, which is supposedly a celebration of many years of producing high quality tools, is absolutely dreadful. The pivot is loose and the tool actually rattles if held by one arm. Peening will likely fix it, but I haven't bothered yet, it just got thrown in a drawer in disgust.
-
@SirVicaLot said:
I received my Micra today and went to test it right away. Unfortunately i was quickly really disappointed. Not sure if mine was just flawed, but the scissors were really bad.While they were somewhat decent cutting paper and thin cardboard, they were not able to cut the plastic shipping sleeve or some cheap Chinese paracord. Instead of cutting the paracord it just got stuck in between the two scissor halves.
I inspected the scissors closely, but could not see any damage. So i decided to sharpen them, but the result was the same. I attached two photos, maybe someone sees something wrong with i do not.Has anyone had a similar experience? I was really disappointed since the scissors are the main tool on the micra. :-\
I had two Micras so far and both are fine.
They're both an older generation though.The pivot on yours looks weird to me

Mine does not show that funny bump.
Is it loose maybe?Update:
Just made a quick gif.
To reproduce your problem I did use the very end as you did, although that's not ideal in general.The scissors pushed the paracord a bit forward so missed the very end. But snapped through it fully...

-
Now I'm wondering about mine...
-
The best scissors is the one on the Surge.
-
Reported recently that my Micra would not cut thread and certainly not paracord. It did cut paper great but
I was not happy. I tweaked them ever so slightly, bent the cutting edge closer together along the whole cutting edge. They were sharp but the space in the center of the cutting surface was gapped.They work great now and will cut thread along the whole cutting edge.
We are spoiled with Vic scissors. On a side note, my Style CS is flawless as are my Squirt scissors.
-
Both my Micras cut about the same but one cuts better towards the front and the other better towards the back. I find my Surge scissors the same, they cut better towards the front for fine things.
The best scissors Leatherman ever made IMO are the ones on later PST II's and the OG Wave.
-
... runs off (with scissors) to find things to cut...
-
@gerleatherberman said:
Sounds like the jaws aren't close enough together. Wonder if that is why the seller let such an old Micra go? Perhaps a little peening is in order?
-
@gadgetman7 said:
Peening it might help.Sent from my iPhone using Tapatalk
I'm Swedish and google doesn't translate Peening. Is that squeeze it in a vise or slam it with a sledgehammer?

-
Tighten the rivet by striking with a ball and peen hammer.
-
@Happy Gilmore said:
dude, literally just saw a video of that tool. Holy moly, those things are sheers not scissors! They are so thick on each side, definitely getting one as a scissor benchmark tool.
That's a gem of a scissor MT with a tiny price tag. U will love it. But note that the rest of the tools that comes with it are just meh...

-
@Sam Lim said:
That's a gem of a scissor MT with a tiny price tag. U will love it. But note that the rest of the tools that comes with it are just meh...
I was going to do a Sewing Multi-tool mod using a micra, but I think the craftsman would be actually much much better both because of its size and construction. I was going to put bobins and such on the tool to make it a leather stitching tool and sewing kit in one. This is literally the perfect size.
Cheers,
HG
Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login

